16 October 2024 in IEEE Transactions on Instrumentation and Measurement
Total Least Squares (TLS) has been comprehensively explored over the last few decades due to its excellent statistical properties. However, the unsatisfactory efficiency of TLS from the intricate process of inverting large matrices limits its practical applications, especially when processing big data. To address this issue, we propose two Recursive Total Least Squares (RTLS) solutions based on the grouping strategy, where all the observations are partitioned into given independent subsets. Within approximated RTLS, observations in the new subset are recursively integrated with results from preceding subsets. The sequential solution is further extended to be exact RTLS. Both approximated RTLS and exact RTLS can significantly reduce the matrix dimensions in the calculation. The proposed methods are compared with several existing algorithms with the experiments of 2D line fitting, image registration, and reference network transformation. In the three experiments, our solutions improve the efficiency of TLS by more than one order of magnitude.
23 August 2024 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
13 May 2025 in Journal of Synchrotron Radiation
The continuous-wave free-electron laser (CW-FEL), based on superconducting radiofrequency (SRF) technology with an electron bunch repetition rate of up to MHz levels, is one of the most advanced light sources, providing exceptionally high average and peak-brightness FEL pulses. Among the new CW-FEL facilities worldwide, the recently proposed Dalian Advanced Light Source (DALS) occupies a unique position as an extreme ultraviolet (EUV) facility primarily designed for chemical physics research. Since the beam emittance requirement for DALS is not as stringent as that for X-ray CW-FEL facilities, a direct current (DC) gun is considered as the primary electron source, with a very high frequency (VHF) gun also planned. To demonstrate key technologies and characterize the electron beam performance, a superconducting CW injector testbed, named the Electron Source Test Facility (ESTF), has been designed and is currently under construction. The testbed is uniquely designed to accommodate both guns with minimal switching effort, where the rest of the beamline layout remains unchanged except for the swapped guns. The two-gun switching scheme for the testbed is shown to be a feasible and cost-effective approach. Furthermore, the injector performance with both guns has been evaluated through a start-to-end simulation based on the DALS configuration, including the production of electron beam in the ESTF injector, the following beam acceleration and compression in a superconducting linear accelerator, and finally the beam lasing performance in the undulator section. The evaluation confirms that the DC gun is a promising electron source for CW-FEL facilities, especially for EUV applications, even though all currently constructed CW facilities have employed the VHF gun. This paper provides a comprehensive description of the injector design and the corresponding performance evaluation.
1 October 2024 in Review of Scientific Instruments
The accuracy of laser trackers in large-scale dimensional metrology is subject to various influencing factors, with instrument positioning being a primary source of error. To address this, a multi-objective optimization algorithm, grounded in the Pareto improvement principle, is proposed. This algorithm is designed to optimize instrument placement, thereby minimizing measurement errors and enhancing the algorithm’s efficacy in error reduction. Thereby, this article proved that positioning the laser tracker consistently on one side of the measurement area and aligning its height with the measuring points can effectively reduce the uncertainty of control point errors by up to 50%.
1 January 2026 in IEEE Transactions on Instrumentation and Measurement
27 February 2026 in Measurement Science and Technology
Accurate three-dimensional (3D) line fitting to point data is a fundamental task in alignment engineering, particularly in applications such as quadrupole smoothing and undulator shimming. However, conventional fitting methods often neglect errors in certain coordinate components and exhibit limited robustness in the presence of outliers. To overcome these limitations, we formulate the 3D line fitting problem as an errors-in-variables (EIVs) model, explicitly accounting for the statistical characteristics of all observed variables. The EIV model is solved iteratively using a total least squares approach. To further improve robustness, we introduce an equivalent weighting scheme based on standardized residuals, which effectively suppresses the influence of outliers while preserving the correlation structure among observations. The proposed method is validated through three case studies: a simulated line fitting experiment, an elliptical undulator girder measurement, and a quadrupole smoothing task. Comparative results with the existing algorithms and the spatial analyzer software demonstrate the superior robustness and accuracy of the proposed approach.