20 January 2023 in Advanced Energy Materials
LiNi0.5Mn1.5O4 (LNMO) cathode active materials for lithium‐ion batteries have been investigated for over 20 years. Despite all this effort, it has not been possible to transfer their favorable properties into applicable, stable battery cells. To make further progress, the research perspective on these spinel type materials needs to be updated and a number of persisting misconceptions on LNMO have to be overcome. Therefore, the current knowledge on LNMO is summarized and controversial points are addressed by detailed considerations on the composition and crystallography of LNMO. The findings are supported by an in‐situ high temperature X‐ray diffraction study and the investigation of four different types of LNMO materials, including Mn(III) rich ordered LNMO, and disordered LNMO with low Mn(III) content. It is shown that the importance of cation order is limited to a small composition range. Furthermore, new evidence contradicting the idea of oxygen defects in LNMO is presented and an enhanced classification of LNMO based on the Ni content of the spinel phase is proposed. Moreover, a balanced chemical equation for the formation of LNMO is presented, allowing for comprehensive calculations of key properties of LNMO materials. Finally, suitable target compositions and calcination programs are suggested to obtain better LNMO materials.
22 May 2019 in Chemistry of Materials
Li-rich disordered rock-salt oxides such as Li1.2Ni1/3Ti1/3Mo2/15O2 are receiving increasing attention as high-capacity cathodes due to their potential as high-energy materials with variable elemental composition. However, the first-cycle oxygen release lowers the cycling performance due to cation densification and structural reconstruction on the surface region. This work explores the influence of lithium excess on the charge compensation mechanism and the effect of surface modification with LiNbO3 on the cycling performance. Moving from a stoichiometric LiNi0.5Ti0.5O2 composition toward Li-rich Li1.2Ni1/3Ti1/3Mo2/15O2, oxygen redox is accompanied by oxygen release. Thereby, cationic charge compensation is governed by the Ni2+/3+ and Mo3+/6+ redox reaction. Contrary to the bulk oxidation state of Mo6+ in the charged state, a mixed Mo valence on the surface is found by XPS. Furthermore, it is observed that smaller particle sizes result in higher specific capacities. Tailoring the surface properties of Li1.2Ni1/3Ti1/3Mo2/15O2 with a solid electrolyte layer of LiNbO3 altered the voltage profile, resulting in a higher average discharge voltage as compared to the unmodified material. The results hint at the interdiffusion of cations from the metal oxide surface coating into the electrode material, leading to bulk composition changes (doping) and a segregated Nb-rich surface. The main finding of this work is the enhanced cycling stability and lower impedance of the surface-modified compound. We argue that surface densification is mitigated by the Nb doping/surface modification.
1 June 2015 in Physical Chemistry Chemical Physics
LiNi0.5Mn1.5O4 spinel cathode was studied during the first discharge cycle using combined full field TXM and XANES techniques to follow the chemical phase transformation as well as the microstructural evolution of cathode materials upon operation within an electrochemical cell.
13 July 2015 in CrystEngComm
For possible future application as cathode material in lithium ion batteries, the lithium insertion mechanism of trirutile-type LiNiFeF6 was investigated.
16 May 2022 in Journal of Applied Crystallography
Laboratory X-ray diffractometers are among the most widespread instruments in research laboratories around the world and are commercially available in different configurations and setups from various manufacturers. Advances in detector technology and X-ray sources push the data quality of in-house diffractometers and enable the collection of time-resolved scattering data during operando experiments. Here, the design and installation of a custom-built multipurpose laboratory diffractometer for the crystallographic characterization of battery materials are reported. The instrument is based on a Huber six-circle diffractometer equipped with a molybdenum microfocus rotating anode with 2D collimated parallel-beam X-ray optics and an optional two-bounce crystal monochromator. Scattered X-rays are detected with a hybrid single-photon-counting area detector (PILATUS 300K-W). An overview of the different diffraction setups together with the main features of the beam characteristics is given. Example case studies illustrate the flexibility of the research instrument for time-resolved operando powder X-ray diffraction experiments as well as the possibility to collect higher-resolution data suitable for diffraction line-profile analysis.
17 January 2013 in Journal of Materials Science