Mateusz Ochnio

Mateusz Ochnio

Auto-generated profile, based on publicly available information

Mateusz Ochnio

Institute of Fluid Flow Machinery, Polish Academy of Sciences, Fiszera 14, 80-231 Gdansk, Poland

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2019 in Waste Management
Verified
Journal Article
Closed access
Jacek KluskaJacek Kluska
Jacek Kluska
MOMateusz Ochnio
Mateusz Ochnio
Dariusz KardaśDariusz Kardaś
Dariusz Kardaś
ŁHŁukasz Heda
Łukasz Heda

1 April 2020 in Renewable Energy
Verified
Journal Article
Closed access
Jacek KluskaJacek Kluska
Jacek Kluska
TTTomasz Turzyński
Tomasz Turzyński
MOMateusz Ochnio
Mateusz Ochnio
Dariusz KardaśDariusz Kardaś
Dariusz Kardaś


15 June 2021 in International Journal of Energy Research
Verified
Journal Article
Closed access
PDF file
MDMarek Dudyński
Marek Dudyński
KDKarol Dudyński
Karol Dudyński
Jacek KluskaJacek Kluska
Jacek Kluska
MOMateusz Ochnio
Mateusz Ochnio
Paweł KazimierskiPaweł Kazimierski
Paweł Kazimierski
Dariusz KardaśDariusz Kardaś
Dariusz Kardaś

11 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
TTTomasz Turzyński
Tomasz Turzyński
JKJacek Kluska
Jacek Kluska
MOMateusz Ochnio
Mateusz Ochnio
Dariusz KardaśDariusz Kardaś
Dariusz Kardaś
This paper describes characteristics of the combustion of sunflower husk (SH), sunflower husk pellets (SHP), and, for comparison, hardwood pellets (HP). The experiments were carried out using a laboratory-scale combustion reactor. A proximate analysis showed that the material may constitute an alternative fuel, with a relatively high heating value (HHV) of 18 MJ/kg. For SHP, both the maximum combustion temperatures (TMAX = 1110 °C) and the kinetic parameters (temperature front velocity vt = 7.9 mm/min, combustion front velocity vc = 8 mm/min, mass loss rate vm = 14.7 g/min) of the process were very similar to those obtained for good-quality hardwood pellets (TMAX = 1090 °C, vt = 5.4 mm/min, vc = 5.2 mm/min, vm = 13.2 g/min) and generally very different form SH (TMAX = 840 °C, vt = 20.7 mm/min, vc = 19 mm/min, vm = 13.1 g/min). The analysis of ash from SH and SHP combustion showed that it has good physicochemical properties (ash melting point temperatures >1500 °C) and is safe for the environment. Furthermore, the research showed that the pelletization of SH transformed a difficult fuel into a high-quality substitute for hardwood pellets, giving a similar fuel consumption density (Fout = 0.083 kg/s·m2 for SHP and 0.077 kg/s·m2 for HP) and power output density (Pρ = MW/m2 for SHP and 1.5 MW/m2 for HP).

30 May 2020 in Chemical Papers
Verified
Journal Article
Open access
PDF file
MOMateusz Ochnio
Mateusz Ochnio
JKJacek Kluska
Jacek Kluska
Dariusz KardaśDariusz Kardaś
Dariusz Kardaś
The present paper concerns the partial updraft gasification of wheat–rye straw pellets, using air as a gasification agent. The aim of this paper is to examine the impact of biochar and ash outflow during the updraft gasification process on the parameters of the latter. For this purpose, a series of five experiments with different parameters of biochar and ash outflow and a reference experiment were carried out with a constant amount of supplied air. The results of the research show that higher volumetric outflows of biochar and ash increase the calorific value (from 6.7 to 7.4 MJ/Nm3) and production (from 34.8 to 40.3 Nm3/h) of the producer gas, as well as the rate of fuel feed rate (from 30 to 43 kg/h). Reductions in the yield of gas (from 1.16 to 0.94 Nm3/kgfuel), equivalence ratio (from 0.125 to 0.087), and cold gas efficiency (from 44.7 to 40.2%) were observed. The content of gravimetric tar in producer gas was typical of updraft gasification and fluctuated within a range of 65‒125 g/Nm3.