28 September 2018 in ACS Nano
Exfoliation of large-area monolayers is important for fundamental research and technological implementation of transition metal dichalcogenides. Various techniques have been explored to increase the exfoliation yield, but little is known about the underlying mechanism at the atomic level. Here, we demonstrate gold-assisted mechanical exfoliation of monolayer molybdenum disulfide, up to a centimeter scale. Detailed spectroscopic, microscopic, and first-principles density functional theory analyses reveal that strong van der Waals (vdW) interaction between Au and the topmost MoS2 layer facilitates the exfoliation of monolayers. However, the large-area exfoliation promoted by such strong vdW interaction is only achievable on freshly-prepared clean and smooth Au surfaces, while rough surfaces and surfaces exposed to air for more than 15 min result in negligible exfoliation yields. This technique is successfully extended to MoSe2, WS2, WSe2, MoTe2, WTe2 and GaSe. In addition, electrochemical characterization reveals intriguing interactions between monolayer MoS2 and Au. A sub-nanometer MoS2 monolayer strongly passivates the chemical properties of the underlying Au and the Au significantly modulates the electronic band structure of the MoS2, turning it from semiconducting to metallic. This could find applications in many areas, including electrochemistry, photovoltaics and photocatalysis.
24 August 2018 in Science
A preference for acids: When titanium dioxide surfaces are exposed to water under ambient conditions, an ordered overlayer forms. Balajka et al. studied this process with scanning tunneling microscopy and x-ray photoelectron spectroscopy for water adsorption under vacuum conditions and in air (see the Perspective by Park). The ordered overlayer was only formed in air, the result of the adsorption of organic acids (formic and acetic acids). Although other species such as alcohols were present in much higher concentrations in air, the bidentate adsorption and entropic effects favored acid adsorption. Science , this issue p. 786 ; see also p. 753
1 October 2003 in Annual Review of Physical Chemistry
▪ Abstract Anisotropic etchants selectively reveal a specific crystallographic plane. Although prized industrially, these etchants are poorly understood because they target specific defect sites on a surface. New methods, which rely on a combination of scanning tunneling microscopy, kinetic Monte Carlo simulations, and infrared spectroscopy, have been developed to quantify these reactions. By correlating the measured reaction rates with the structure of the defects, information about reaction mechanisms can be obtained. These techniques have also been extended to allow for the quantification of impurity reactions such as the reaction of dissolved O2, and of nonetching additives, such as alcohols. A complementary macroscopic technique, which utilizes microfabricated arrays of miscut surfaces to measure orientation-dependent kinetics, is also described.
1 November 1994 in The Journal of Chemical Physics
We have measured the unenhanced, nonresonant surface Raman spectra of one monolayer of hydrogen bound to flat and stepped Si(111) surfaces prepared using a novel, aqueous fluorine etch. The orientation and normal mode composition of adsorbate vibrations are obtained from polarized, angle-resolved Raman spectra using a 3-layer dielectric model. This approach requires the experimental determination of both the anisotropy in the dynamic polarizability of the adsorbate bond and the effective dielectric constant in the vicinity of the adsorbate. The measured Si–H bond anisotropy is 0.263±0.028 in good agreement with gas phase measurements. The adsorbate dielectric constant is measured to be 3.78±0.20; this response is clearly nonlocal and predominantly due to polarization of the underlying silicon lattice. Using this technique, we find that the step dihydride on a Si[6(111)-(1̄1̄2)] surface is rotated 37°±4° from the surface normal in good agreement with the 31° predicted by ab initio cluster techniques, but significantly larger than the 12.5° predicted by pseudopotential slab calculations. In contrast to both theoretical predictions, the normal modes of this step dihydride display little concerted motion indicating that subsurface relaxation near the step edge reduces steric interactions much further than predicted. The observed anisotropic etch rates, evidenced by the production of atomically straight steps, are explained in terms of the measured distortion at the step edge.
18 March 2022 in Physical Review Letters
The properties of photoemission electron sources determine the ultimate performance of a wide class of electron accelerators and photon detectors. To date, all high-efficiency visible-light photocathode materials are either polycrystalline or exhibit intrinsic surface disorder, both of which limit emitted electron beam brightness. In this Letter, we demonstrate the synthesis of epitaxial thin films of on 3C-SiC (001) using molecular-beam epitaxy. Films as thin as 4 nm have quantum efficiencies exceeding 2% at 532 nm. We also find that epitaxial films have an order of magnitude larger quantum efficiency at 650 nm than comparable polycrystalline films on Si. Additionally, these films permit angle-resolved photoemission spectroscopy measurements of the electronic structure, which are found to be in good agreement with theory. Epitaxial films open the door to dramatic brightness enhancements via increased efficiency near threshold, reduced surface disorder, and the possibility of engineering new photoemission functionality at the level of single atomic layers.
14 June 2021 in Applied Physics Letters
Alkali antimonide photocathodes are capable of generating high brightness electron beams given their high quantum efficiency and low mean transverse energy (MTE). Increasing the brightness of the photoemitted electron beams beyond the current state of the art requires surface control of the photocathode at the atomic scale, since the beam brightness at the cathode is degraded by a rough, inhomogeneous surface. In this work, we grow cesium antimonide photocathodes on single crystal substrates (Al2O3, TiO2, 3C–SiC, and a control sample on Si) and study the resulting surface morphology with scanning tunneling microscopy (STM). We observe dramatic changes in surface morphology across substrates. In particular, we demonstrate 10 times larger island size and significantly reduced roughness on two samples grown on 3C–SiC(100) substrates as compared to samples on other substrates. By computing the local electric fields which these surfaces would generate in an electron accelerator source, we estimate the roughness-induced contribution to MTE. Across samples, the calculated contribution to MTE varies by a factor of 17, and the smallest value computed is 12 meV at an extraction field of 50 MV/m, which is smaller than typical values for alkali antimonides. Additionally, we show that oxidation, commonly encountered in vacuum transfer and in accelerator operation, does not affect the measured surface morphology. Our findings suggest that even in high field environments, the brightness of the photocathodes grown on 3C–SiC will be primarily determined by the material's electronic properties rather than by spurious fields generated by photocathode roughness.