Murali Krishnan R.

Murali Krishnan R.

Auto-generated profile, based on publicly available information

Murali Krishnan R.

Affiliation Department of Mechanical Engineering, Karpagam Institute of Technology, Coimbatore, Tamil Nadu, India

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 January 2025 in Engineering Research Express
Verified
Journal Article
Closed access
MRMurali Krishnan R
Murali Krishnan R
RRRajesh Ranganathan
Rajesh Ranganathan
SASaiyathibrahim A
Saiyathibrahim A
RVRajkumar Velu
Rajkumar Velu
VJVijaykumar S Jatti
Vijaykumar S Jatti
PVPraveenkumar V
Praveenkumar V
The current research aims to optimize the multi-response during Wire Electrical Discharge Machining (Wire-EDM) of SLMed AlSi10Mg by using Taguchi integrated Grey Relational Analysis (GRA). Selective Laser Melting (SLM) is one of the most well-known and practical Additive Manufacturing (AM) methods, with the potential to replace many traditional production processes. The complex metallic support structures created during SLM require special attention as they are difficult to remove by hand. Therefore, this study performs post-processing using the Wire-EDM precision machining technique to evaluate the machinability of the SLMed AlSi10Mg as-built part. The multi-response optimization in this study aims to achieve the maximum material removal rate and the lowest surface roughness while considering four important influencing factors (pulse On time, pulse Off time, servo voltage, and wire feed rate) at four distinct levels. The Taguchi integrated Grey Relational Analysis (GRA) revealed that a pulse On time of 118 μs (Level 3), a pulse Off time of 44 μs (Level 1), a servo voltage of 60 V (Level 4), and a wire feed rate of 7 m s−1 (Level 4) are recommended to achieve optimal machining of SLMed AlSi10Mg. Furthermore, the derived optimization results were carefully verified through a confirmatory experiment, which showed a 38.57% improvement in multi-response characteristics compared to the initial Wire-EDM parameter settings. The methodology proposed in this work offers a standardized approach that has the potential to be implemented for the rapid and precise prediction and optimization of surface roughness, while achieving better material removal during Wire-EDM of SLMed AlSi10Mg.

2 June 2025 in PLOS ONE
Verified
Journal Article
Open access
PDF file
VJVijaykumar S Jatti
Vijaykumar S Jatti
ASA. Saiyathibrahim
A. Saiyathibrahim
AYArvind Yadav
Arvind Yadav
MRMurali Krishnan R.
Murali Krishnan R.
BJB. Jayaprakash
B. Jayaprakash
EBEbenezer Bonyah
Ebenezer Bonyah
In this study, the ability of machine learning algorithms to predict tensile properties of both heat-treated and non-heat treated LPBFed AlSi10Mg alloy is investigated. The data was analyzed using various Machine Learning Regression (MLR) models such as Linear Regression (LR), Gaussian Process Regression (GPR), Random Forest Regression (RFR), and Decision Tree (DT). The AlSi10Mg alloys, heat-treated and non heat-treated, had different tensile characteristics. The tensile characteristics were forecasted using trained and evaluated MLR models. Because the performance of various MLR models has been verified by several performance indicators, such as Root Mean Square Error (RMSE), R2 (coefficient of determination), Mean Square Error (MSE), and Mean Absolute Error (MAE). Moreover, scatter plots were made for checking the accuracy of the forecast. The GPR model demonstrated better prediction performance than the other three models, i.e., higher R2 values and lower error values for the heat-treated samples. For predicting the UTS value of non-heat treated samples, the LR model performs very well with R2 of 1.000. In that case, GPR has the better predictive performance for the other tensile features in non-heat treated samples. Summing up, it is obvious that GPR is well capable of predicting tensile properties of AlSi10Mg alloy with high precision. This indicates how important GPR is to additive manufacturing to achieve great quality.

1 April 2025 in AIP Advances
Verified
Journal Article
Open access
PVPraveenkumar V
Praveenkumar V
SASaiyathibrahim A
Saiyathibrahim A
PDPraveen Kumar D
Praveen Kumar D
MRMurali Krishnan R
Murali Krishnan R
VJVijaykumar S Jatti
Vijaykumar S Jatti
JSJohnson Santhosh
Johnson Santhosh
This study investigates the influence of Laser Powder Bed Fusion (LPBF) processing parameters of high-performance Ti6Al4V components on mechanical properties and microstructural uniformity. Experimental results indicate that lower laser power (200–203 W) and moderate scan speeds (600–604 mm/s) optimize the hardness and the Hatch distance (0.10–0.11 mm) and layer thickness (0.04–0.05 mm) significantly impact hardness, with specific parameter combinations yielding superior results. A comparative assessment of six metaheuristic algorithms, such as the JAYA algorithm, Cohort Intelligence (CI), Particle Swarm Optimization (PSO), Teaching-Learning-Based Optimization (TLBO), Genetic Algorithm (GA), and Simulated Annealing (SA), was performed for LPBF parameter optimization. JAYA and CI exhibited the fastest convergence, achieving peak fitness values within the first five iterations and demonstrating high stability with minimal oscillations. The results show a significant improvement in hardness, consistently ranging between 560 and 570 HV. JAYA and CI reached comparable maximal hardness measurements at 570 HV, which agreed with the laboratory-reported 428.6 HV value. The HYV values obtained by PSO and TLBO algorithms were competitive at about 569.5 HV yet displayed reduced accuracy in their results. GA and SA showed moderate to slow convergence speed, which led to unreliable precision in their application. JAYA and CI demonstrate better performance through their effective balancing capability of exploitation and exploration processes that enable rapid and stable convergence. Given its simplicity alongside its accuracy and robust performance, the JAYA algorithm proves the most appropriate method for LPBF parameter optimization. Real-time applications benefit from CI as a promising solution.

14 May 2025 in Next Research
Verified
Journal Article
Closed access
RPR Premkumar
R Premkumar
RBR Ramesh Babu
R Ramesh Babu
SASaiyathibrahim A
Saiyathibrahim A
VJVijaykumar S Jatti
Vijaykumar S Jatti
VNVijayan S N
Vijayan S N
BKBALAJI KARUPPIAH
BALAJI KARUPPIAH

3 December 2025 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
RKR. Murali Krishnan
R. Murali Krishnan
RRRajesh Ranganathan
Rajesh Ranganathan
ASA. Saiyathibrahim
A. Saiyathibrahim

16 June 2025 in Metal Working and Material Science
Verified
Journal Article
Closed access
VJVijaykumar S Jatti
Vijaykumar S Jatti
VSVijayan Singarajan
Vijayan Singarajan
ASA. Saiyathibrahim
A. Saiyathibrahim
VJVijaykumar S Jatti
Vijaykumar S Jatti
MKMurali Krishnan
Murali Krishnan
SJSavita Jatti
Savita Jatti
Introduction: Machining hard materials and shape memory alloys (SMAs), such as NiTi, NiCu, and BeCu, using conventional techniques is challenging due to excessive tool wear and poor surface finish. Non-conventional machining methods, particularly electrical discharge machining (EDM), offer improved precision and surface quality. However, the effectiveness of EDM is contingent upon the optimization of process parameters. The purpose of this study is to optimize EDM parameters to enhance the machining performance of SMAs by considering factors such as pulse-on time, pulse-off time, discharge current, gap voltage, and workpiece electrical conductivity. Methods. In this study, the Taguchi experimental design approach was employed to analyze the influence of key process parameters on the material removal rate (MRR), surface roughness (SR), and tool wear rate (TWR). Analysis of variance (ANOVA) was then applied to identify the most statistically significant factors affecting machining performance. A multi-objective optimization method, based on utility theory, was utilized to determine the optimal EDM settings that balance MRR, SR, and TWR. The results were validated through experimental trials. Results and Discussion. The experimental results indicated that Trial 15 achieved the highest MRR of 9.076 mm³/min, while Trial 1 produced the lowest SR of 2.238 µm. The minimum TWR of 0.041 mm³/min was observed in Trial 10, which contributes to increased tool lifespan. ANOVA revealed that gap voltage was the most influential factor, accounting for 85.98% of the variation in machining performance, followed by discharge current (4.76%) and pulse-off time (2.59%). The multi-objective optimization process successfully identified parameter configurations that optimize MRR while minimizing SR and TWR. The prediction model developed in this study demonstrated high accuracy, with an R² value of 93.3% and an adjusted R² of 89.7%. Validation experiments confirmed the effectiveness of the optimized parameters, resulting in an average MRR of 8.852 mm³/min, SR of 2.818 µm, and TWR of 0.148 mm³/min. The findings presented herein confirm that careful optimization of EDM parameters significantly enhances the machining performance of SMAs, considerably improving machining efficiency and tool longevity.