14 September 2023 in Nuclear Fusion
The limited tritium resources available for the first fusion power plants (FPPs) make fuel self-sufficiency and tritium inventory minimization leading issues in FPP design. This work builds on the model proposed by Abdou et al (2020 Nucl. Fusion 61 013001), which analyzed the fuel cycle (FC) of a DEMOnstration nuclear FPP-class FPP with a time-dependent system-level model. Here, we use a modified version of their model to analyze the FC of an Affordable, Robust, Compact (ARC)-class tokamak and two versions of a Spherical Tokamak for Energy Production (STEP)-class tokamak. The ARC-class tokamak breeds tritium in a 2LiF + BeF2 liquid immersion blanket, while the STEP-class tokamak breeds tritium utilizing either a liquid-lithium blanket design or an encapsulated breeding blanket. A time-dependent system-level model is developed in Matlab Simulink® to simulate the evolution of tritium flows and tritium inventories in the FC. The main goals of this work are to assess tritium self-sufficiency of the ARC- and STEP-class designs and to determine quantitative design requirements that can be used to analyze the adequacy of a proposed FC system. These design requirements are aimed at achieving a low tritium inventory doubling time ( ) and a low start-up inventory ( ) while keeping the required tritium breeding ratio (TBR ) as low as possible. We also consider how improvements in FC technology and POs affect TBR and . The model results show that TBR for ARC- and STEP-class FPPs should be achievable if the tritium burn efficiency (TBE) reaches 0.5%–1% (TBR 1.2). This assumes significant, but attainable, improvements over current abilities. However, the model results indicate that an FPP must achieve ambitious performance targets, including FPP availability 70%, tritium processing time 4 h, and the implementation of direct internal recycling (DIR). If future research yields major improvements to achievable TBE, it may be possible to achieve tritium self-sufficiency while operating at lower availability and without implementing DIR.
22 March 2024 in International Journal of Hydrogen Energy
1 December 2019 in Nuclear Materials and Energy
20 October 2021 in Nuclear Fusion
22 February 2021 in Nuclear Fusion
This work investigates the influence of hydrogen chemical potential continuity across solid material interfaces. The implementation of the mathematical model in FESTIM is verified using the method of exact solutions (MES) and the method of manufactured solutions (MMS) in 1D, 2D, with complex material properties and inhomogeneous temperature fields. A comparison test between FESTIM, TMAP7 and Abaqus codes is also performed and the codes show good agreement. The chemical potential continuity condition has an impact up to 40% on the outgassing particle flux on 4 mm composite slabs (W/Cu and Cu/EUROFER) compared to mobile concentration continuity. A method for rapid identification of materials properties from outgassing flux measurements is given. The influence of chemical potential conservation on monoblock inventory is then studied. It is shown that, for the 1D and 2D ITER divertor monobolocks cases, discrepancies only start to appear after approximately 5 × 106 s of full power.
20 October 2020 in Scientific Reports
A parametric study is performed with the 2D FESTIM code for the ITER monoblock geometry. The influence of the monoblock surface temperature, the incident ion energy and particle flux on the monoblock hydrogen inventory is investigated. The simulated data is analysed with a Gaussian regression process and an inventory map as a function of ion energy and incident flux is given. Using this inventory map, the hydrogen inventory in the divertor is easily derived for any type of scenario. Here, the case of a detached ITER scenario with inputs from the SOLPS code is presented. For this scenario, the hydrogen inventory per monoblock is highly dependent of surface temperature and ranges from $$10^{18}$$ to $$6 \times 10^{19}$$ H after a $$10^{7}$$ s exposure. The inventory evolves as a power law of time and is lower at strike points where the surface temperature is high. Hydrogen inventory in the whole divertor after a $$10^{7}$$ s exposure is estimated at approximately 8 g.