DIL e.V. - German Institute of Food Technologies, Professor-von-Klitzing-Str. 7, Quakenbrück 49160, Germany; Food Structure & Function Research Group, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, Gent 9000, Belgium
Auto-generated profile, based on publicly available information
Sarah Schroeder
DIL e.V. - German Institute of Food Technologies, Professor-von-Klitzing-Str. 7, Quakenbrück 49160, Germany; Food Structure & Function Research Group, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, Gent 9000, Belgium
Plant-based emulsion gels can be used as solid animal fat substitutes for vegan sausages. For this reason, commercially available protein isolates with different amino acid profiles from pea, soy and potato (Pea-1, Pea-2, Soy, Potato) have been tested for their ability to form shape stable emulsions gels at neutral pH and upon heating to 72 °C. In order to obtain emulsion gels that are as solid as possible, the protein concentrations in the continuous phase (CPC, 8.0–11.5% (w/w)) and the oil mass fractions (65–80%) were varied. For leguminous proteins, a positive correlation of both parameters on emulsion rigidity was shown, indicating that both, interfacial and protein–protein interactions, are involved in structure reinforcement. Firmness increased with increasing content in cysteine (Pea-1 < Pea-2 < Soy) and the interactions were of electrostatic, hydrophobic and hydrophilic nature. Potato emulsion rigidity was independent of CPC and oil content. The emulsions showed a much higher degree in crosslinking, and very low charge density. Temperature-sweep analysis and CLSM revealed that Potato protein gelled as consequence to low temperature stability. Hence, the structure reinforcement in Potato emulsions mainly contributed to the protein network, with 70% oil and CPC 11.5% forming a hybrid gel with highest firmness. However, gelling of Potato protein also resulted in interfacial adsorption of protein aggregates and reduced interfacial stability with increasing CPC. This was demonstrated in the amount of extractable fat which was 2.0 and 0.6% for Pea-1 and 2 emulsions, 6.4% for Soy and 34.4% of total fat for Potato emulsions.
14 April 2024 in European Food Research and Technology
Chocolate mass is a cocoa butter-based suspension, which mainly consists of sugar and cocoa particles dispersed in a continuous lipid phase. During chocolate manufacturing, sugar particles have to be ground to sizes below 25–30 µm. Such a fine grinding is carried out either by five roll refiners or by ball mills. Despite obtaining similar particle size distributions at the end, the grinding procedures result in different chocolate mass properties. The reasons for that are not fully understood, so far. Therefore, changes in particle sizes and surface properties of sucrose particles as well as their interactions with surrounding cocoa butter during the different grinding processes were investigated including atomic force microscopy techniques to characterize local surface states. It was found that especially the alteration of surfaces during continued grinding differed. In the case of roller grinding, surface states became more inhomogeneous and different surfaces states at microscopic level existed in parallel. More homogenous surfaces but with a higher degree of amorphous states were formed during grinding in the ball mill. Variations in macroscopic behavior of the suspension can be explained by the differences in interaction of particles with each other and with the surrounding lipid phase.
Surface free energy (SFE) is an important surface property in food processing as it determines the wettability of solid surfaces or the interaction of mould surfaces and chocolate during the moulding process. High-resolution information about SFE could be useful to understand gloss inhomogeneities of chocolates after de-moulding. SFE is connected with adhesion properties. Thus, Atomic force microscopy (AFM) adhesion measurements can be applied to determine SFE of a solid surface at microscopic scale. For this purpose, AFM tips were functionalized to modify their SFE and used for adhesion measurements at three different chocolate gloss areas (matt, glossy and homogenous) via AFM force maps. Influence of relevant parameters such as surface roughness, contact area, relative humidity, and SFE of functionalized tips was considered. Two different mathematical approaches based on Johnson-Kendall-Roberts theory were used to calculate SFE from adhesion values. The measured adhesion values showed variations depending on functionalized tip and chocolate gloss area. The results showed a difference in adhesion and, consequently, SFE in the different gloss areas with gloss > homogenous > matt. However, SFE obtained from adhesion forces were not decisive enough to enable a direct correlation with SFE data from contact angle measurements at the same area.