Xufeng Shen

Xufeng Shen

Auto-generated profile, based on publicly available information

Xufeng Shen

State Key Laboratory of Fluid Power Components and Mechatronic Systems, Zhejiang University, Hangzhou, Zhejiang, P. R. China

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2011 in Procedia Engineering
Verified
Journal Article
Open access
ZLZhongxing Li
Zhongxing Li
JZJingjing Zhu
Jingjing Zhu
XSXufeng Shen
Xufeng Shen
CZCong Zhang
Cong Zhang
JGJiwei Guo
Jiwei Guo
On the basis of the analysis of vibration characteristics of motor bearing faults and the influence from testing noise on site, calculation of the symptom parameters representing the vibration signals according to the measured vibration signals is proposed, and the sensitivity analysis is carried out to these parameters which can refine effective symptom parameters. As there are limitations for motor bearing fault intelligent diagnosis methods based on genetic algorithm and neural network, while Bayesian network has a good learning, inference and astringency. Therefore, the effective combination of the symptom parameters and Bayesian network is made and a new intelligent diagnosis method is posed

1 July 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
XSXufeng Shen
Xufeng Shen
XLXin Li
Xin Li
Viscous flow resistance is dominated by viscous friction between fluid and wall. The flow resistance characteristic curve (i.e., the relationship curve between pressure drop and flow rates, represented as the Δp–Q curve) depends on some inherent characteristic variables, such as structural size, fluid viscosity, density, and temperature. Usually, to change the Δp–Q curve, these inherent characteristic variables must be changed. This paper proposes a new design of variable viscous flow resistance. The new design uses two disks to construct a slit flow channel, and rotate one of the disks to drive the fluid in the slit flow channel to form a rotational inertia effect. Therefore, by changing the rotating speed of the disk, the rotational inertia effect can be changed, thereby achieving the purpose of changing the Δp–Q curve. This paper derives a theoretical model for the pressure distribution of the rotating slit flow field and conducted experimental verification. It was found that the rotational inertia gradient and viscous gradient terms play major roles in governing the radial pressure gradient. The sum of the other two inertial gradient terms accounts for a maximum of about 1.58% of the total pressure gradient. There is a coupling relationship between circumferential velocity, radial velocity, and flow rates. An increase in Q can increase the rotational inertial gradient term by up to 24.9%. The rotating disk causes additional radial velocity and thus weakens the viscous gradient term by at least 16.41%.

1 November 2024 in Physics of Fluids
Verified
Journal Article
Closed access
XSXufeng Shen
Xufeng Shen
YXYuan Xu
Yuan Xu
KSKaige Shi
Kaige Shi
XLXin Li
Xin Li
A rotating gap structure is a type of viscous flow resistance using two disks where the rotation of one disk drives the fluid within the gap, generating rotational inertia. This inertia, combined with viscous friction, determines the flow resistance characteristic curve (pressure drop vs flow rate, or Δp-Q curve). By adjusting the disk's rotational speed, the rotational inertia and the Δp-Q curve can be modified. This paper examines how the radial flow direction (positive and negative) affects the circumferential velocity, radial velocity, and the Δp-Q curve of the rotating gap structure through theoretical modeling and experiments. Results show that radial flow direction and rate influence the symmetric distribution of radial velocity and the linear distribution of circumferential velocity, altering the main components of the Δp-Q curve: the viscous flow resistance curve (Δpvis-Q) and the rotational inertia flow resistance curve (Δprot-Q). The study found that the slope of the Δpvis-Q curve is smaller for positive flow than for negative flow due to differences in radial velocity distribution. Additionally, the circumferential velocity is weakened in positive flow and enhanced in negative flow, resulting in a smaller slope of the Δprot-Q curve for positive flow. These factors cause the Δp-Q curve to deviate from linearity, with greater deviation at higher rotational speeds. Finally, experimental verification was conducted, and the measured Δp-Q curve closely matched the theoretical calculations.

7 November 2023 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
XSXufeng Shen
Xufeng Shen
JXJiawei Xu
Jiawei Xu
XYXubo Yu
Xubo Yu
XLXin Li
Xin Li
Shaft seal covers a very wide range of machinery and applications. Lip seals, which are used for sealing shafts against the exit or ingress of liquids, are a type of shaft seal. Reducing the wear of the sealing ring and extending its service life can increase the time interval for machine maintenance and inspection. In this paper, a disk structure for reducing the pressure difference between the inside and outside of the lip seals is proposed. The disk structure forms a layer of rotating oil film on the seal ring, so the oil pressure near the seal ring is less than in a sealing chamber. First, based on the similarity principle and the hypothesis of von Kármán, a theoretical model of the rotating oil film was established, and the dominant influence of inertia of circumferential velocity and viscosity of radial velocity on pressure distribution was expounded. Then, an experimental device that can measure pressure distribution and temperature was constructed, and a pressure distribution measurement experiment was conducted. Based on theoretical models and experiments, it was proved that the rotating disk could generate a pressure drop and the pressure drop was a function of the square of the rotating speed. The influence of temperature and oil film thickness was studied, and it was found that the increase in the temperature and oil film thickness weakened rotational flow inertia and enhanced radial flow viscosity, increasing pressure within the oil film. Additionally, it was observed that the oil in the sealing chamber produced a sunken liquid level due to the stirring of the rotating disk, which would reduce the boundary pressure at the periphery of the oil film and produce a greater pressure drop inside the oil film.

1 March 2025 in Physics of Fluids
Verified
Journal Article
Closed access
XSXufeng Shen
Xufeng Shen
XLXin Li
Xin Li
The characteristic curve of viscous flow resistance (i.e., the relationship between flow rate and pressure drop, commonly referred to as the Δp-Q curve) depends on several inherent variables, such as structural dimensions, fluid viscosity, density, and temperature. In most cases, altering the characteristic curve of viscous flow resistance requires changing these inherent variables. In previous studies [X. Shen and X. Li, “Variable viscous flow resistance based on rotational inertia,” Phys. Fluids 35, 073612 (2023); X. Shen, J. Xu, X. Yu, and X. Li, “A design based on centrifugal inertia of rotational oil film for reducing pressure at shaft hole,” Proc. Inst. Mech. Eng. Part C-J. Eng. Mech. Eng. Sci. 238, 1295 (2024)], we proposed a novel design approach for variable flow resistance, which modifies the Δp-Q curve by incorporating fluid inertia. The new variable flow resistance utilizes two coaxial disks that are relatively close to each other to construct a slit channel, using air as the fluid medium. When the air passes through the slit channel, it is constrained by the wall to generate viscous resistance. At the same time, the rotation of the lower disk drives the air in the slit flow field to rotate, thereby generating rotational inertia. Consequently, both viscous pressure drop and rotational inertial pressure drop act on the air in the slit. By adjusting the rotation speed, the Δp-Q characteristic curve can be translated. Previous studies were based on the rotation of a single disk. Based on this, we propose the concept of double-layer rotating disks, aiming at enabling the air in the disks to rotate more fully. This approach significantly shifts the Δp-Q curve and improves the linearity of the curve. Based on the similarity principle and von Kármán's hypothesis, a theoretical pressure distribution model for the slit flow field of double-layer rotating disks is derived. The variation of the velocity field in the slit flow path caused by the rotating double-layer rotating disks was investigated. Furthermore, the influences of flow rate and disk rotation speed on the components of the pressure drop are analyzed. Experimental measurements of the Δp-Q curves for the double-layer rotating disks slit flow field at various rotation speeds are conducted to validate the theoretical model. Finally, the theoretical Δp-Q drop characteristic curve is revised to reduce errors. As the rotation speed increases, the Δp-Q curve shifts significantly to the right and demonstrates excellent linearity, with the slope remaining nearly constant. Therefore, this approach can expand the measurement range of flow sensors when applied to flow sensing devices.