30 July 2018 in IET Microwaves, Antennas & Propagation
A novel pattern reconfigurable planar optically controlled Yagi–Uda antenna is proposed. The antenna comprises a director, a driven dipole, a reflector and the substrate. The two parasitic elements loaded with positive intrinsic negative (PIN) photodiodes in the middle, applied as manipulating switches, are capable of varying the radiation pattern by transforming their physical structures. A prototype of the proposed antenna along with PIN photodiodes was fabricated to verify the concept of optically controlled pattern reconfiguration. The simulated and experimental results indicate that the curves and radiation patterns of the proposed antenna in both the PIN switches' on and off state are similar; however, the direction of maximum radiation differs between these two states by . Good unidirectional radiation patterns with the front‐to‐back ratios of 12 and 8 dB are obtained. About 10 dB impedance bandwidth can reach 15% and the maximum gain is more than 6.3 dBi. This study proposes a three‐element equivalent current radiation model based on the current distribution from simulation, which can explain the directional radiation characteristics of the designed antenna well. This pattern reconfigurable antenna can be optically controlled remotely, reducing the effects of controlling network on the antenna radiator.
7 April 2020 in IEEE Access
This paper presents a wideband pattern- and polarization-reconfigurable antenna based on bistable composite cylindrical shells. This antenna, which includes seven radiating metal strips, uses bistable anti-symmetric glass fiber-reinforced polymer (GFRP) composite cylindrical shells as the substrate to achieve reconfigurability without the need for redundant structures or semiconductor devices. This bistable GFRP substrate has two stable cylindrical configurations: extended structure and coiled-up structure. Therefore, by transforming the configuration, the radiation patterns of the proposed antenna are changed, and simultaneously, the polarization is switched between left-handed circular polarization (LHCP) and righthanded circular polarization (RHCP). A prototype of the proposed antenna is fabricated and measured. The measured results indicate that the antenna can operate in the frequency range from 2.3 to 3 GHz in the two configurations. The proposed antenna can be utilized as the payload of a satellite.
1 January 2011 in Progress In Electromagnetics Research Letters
A semicircle monopole printed antenna is proposed. Its radiation unit and the ground plane are in the same shape, and both of them are coplanar-printed. The antenna is fed by a microstrip line, which is connected to the radiation unit through a via-hole. The measured impedance bandwidth is about 3.1 GHz-15.1 GHz with VSWR < 2, and the ratio bandwidth can reach 4.9 : 1. The omnidirectional characteristic is also excellent in H-plane. Moreover, because of the introduction of the semicircle radiation unit and the ground plane, the length of the radiation unit can be miniaturized in polarization direction, which is only 14% of wavelength of the lowest operating frequency. The antenna size is just 29 mm × 29.5 mm × 1.0 mm, which can make it well integrate into UWB communication systems.
2 August 2023 in IEEE Antennas and Wireless Propagation Letters
This letter proposes a novel wideband crossed-dipole antenna that utilizes liquid metal switches for polarization reconfiguration. The antenna consists of a wideband single-fed crossed bowtie dipole with each arm featuring a gradually varying width bent slot. A back cavity structure serves as a reflector to achieve directional radiation and circular polarization (CP) bandwidth enhancement. The proposed antenna uses movable liquid metal columns in microchannels as coupling switches to open or close the slots. By controlling the switches to close either the vertical or horizontal slots, the antenna achieves directional radiation of left-hand circular polarization (LHCP) or right-hand circular polarization (RHCP), respectively. When all the slots are opened or closed simultaneously, the directional radiation of linear polarization (LP) is achieved. Experimental results indicate that the antenna has an impedance bandwidth (IBW) of 65.02% and an axial ratio bandwidth (ARBW) of 43.14% in the circular polarization mode, with a maximum gain of 11.6 dBic. In the linear polarization mode, the antenna exhibits an impedance bandwidth of 42.5% and a maximum gain of 11.48 dBi. These results demonstrate the proposed antenna's versatility and potential for use in mobile communication terminals.
1 November 2017 in IEEE Access
A printed omnidirectional dipole array antenna with a radiated load is proposed and analyzed which is fed by Coplanar Waveguide (CPW). Flying lines and via-holes are used to connect dipoles to achieve a balanced feed. Simulated results by CST Microwave Studio® indicate that the operating band is 4.6 to 4.9GHz with its reflection coefficient less than -10dB. The omnidirectional gain in this band is higher than 4.23dB and the antenna size is only 103.4mm×12.6mm×1.5mm. As a result, its gain per wavelength can reach a high value of 3.1dB/λ at 4.7GHz, which is conducive to antenna miniaturization and batch production. In order to effectively decrease the outer surface current on the coaxial feeder outer conductor a printed choke is introduced so that the antenna performance would not be affected by an even longer coaxial line. The bandwidth and gain are improved achieving 4.63-5.45GHz and 5.8dB, respectively. There is a broad application of the designed antenna for it not only can be used independently, but also can be integrated on the printed circuit board.
5 January 2021 in Microwave and Optical Technology Letters