Zbigniew Ogonowski

Zbigniew Ogonowski

Auto-generated profile, based on publicly available information

Zbigniew Ogonowski

Institute of Automatic Control, Silesian University of Technology, Gliwice, Poland

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2016 in The International Journal of Acoustics and Vibration
Verified
Journal Article
Closed access
Dariusz BismorDariusz Bismor
Dariusz Bismor
KCKrzysztof Czyz
Krzysztof Czyz
ZOZbigniew Ogonowski
Zbigniew Ogonowski

29 March 2018 in Minerals
Verified
Journal Article
Open access
PDF file
Szymon OgonowskiSzymon Ogonowski
Szymon Ogonowski
MWMarta Wołosiewicz-Głąb
Marta Wołosiewicz-Głąb
ZOZbigniew Ogonowski
Zbigniew Ogonowski
Dariusz FoszczDariusz Foszcz
Dariusz Foszcz
Marek PawelczykMarek Pawelczyk
Marek Pawelczyk
Comparison of dry and wet grinding process in an electromagnetic mill is presented in this paper. The research was conducted in a batch copper ore grinding. Batch mode allows for precise parametrization and constant repetitive conditions of the experiments. The following key aspects were tested: processing time, feed size, size of the grinding media, mass of the material and graining media, and density of the pulp. The particles size distribution of the product samples was analyzed in the laboratory after each experiment. The paper discusses the experimental results as well as the concept of dry and wet grinding and classification circuits for the electromagnetic mill. The main points of the discussion are the size reduction effectiveness and power consumption of the entire system.

27 March 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Szymon OgonowskiSzymon Ogonowski
Szymon Ogonowski
ZOZbigniew Ogonowski
Zbigniew Ogonowski
Marek PawelczykMarek Pawelczyk
Marek Pawelczyk
The paper presents an innovative construction and installation of dry grinding in electromagnetic mill that provides a significant reduction of energy consumption when compared to traditional mills. The installation constitutes complex multi-objective plant. To gain control over all the objectives, hierarchical structure of control system was developed where different time-horizons involve multi-rate scheme of steering. The paper presents solutions for the direct regulation, supervisory control, and optimization level. The electromagnetic mill installation constitutes a unique setup that causes open loop instability and implies the application of novel control schemes at all of the levels. The paper presents these solutions and illustrates them with the results of experiments carried out on the electromagnetic mill installations.

1 January 1991 in Chemical Engineering Science
Verified
Journal Article
Closed access
RDRainer Dittmar
Rainer Dittmar
ZOZbigniew Ogonowski
Zbigniew Ogonowski
KDKlaus Damert
Klaus Damert

1 June 2017
Verified
Conference Paper
Closed access
Szymon OgonowskiSzymon Ogonowski
Szymon Ogonowski
ZOZbigniew Ogonowski
Zbigniew Ogonowski
MSMarkus Swierzy
Markus Swierzy
The paper presents optimizing control of the electromagnetic grinding system. The electromagnetic grinding is a complex process, thus formulation of the optimization problem is done in a top-down manner. To do so, the parameters which influence product quality and serves as decision variables are specially selected. The selection follows from environmental analysis of the system and discussion of the dynamics of disturbances which affect the grinding process. The criterion function to be minimized is electrical energy consumption. Algorithms solving optimization problem are described in the paper. The optimizing control performs as adaptive-like system where minimum energy is kept by proper control of the inverter. Control system constitutes an element of SCADA layered structure.

26 September 2016
Verified
Conference Paper
Closed access
Szymon OgonowskiSzymon Ogonowski
Szymon Ogonowski
ZOZbigniew Ogonowski
Zbigniew Ogonowski
Marek PawelczykMarek Pawelczyk
Marek Pawelczyk
The paper presents a model of the air stream ratio in the dry grinding and classification circuit with the electromagnetic mill. The concept of the grinding system is described along with indirect measurement methodology. Model structure and identification problems are discussed and a supervisory control algorithm based on the model is derived.