4 January 2016 in Applied Physics Letters
The surface reactions during atomic layer deposition (ALD) of Al2O3 from Al(CH3)3 and H2O have been studied with broadband sum-frequency generation to reveal what is limiting the growth at low temperatures. The –CH3 surface coverage was measured for temperatures between 100 and 300 °C and the absolute reaction cross sections, describing the reaction kinetics, were determined for both half-cycles. It was found that –CH3 groups persisted on the surface after saturation of the H2O half-cycle. From a direct correlation with the growth per cycle, it was established that the reduced reactivity of H2O towards –CH3 is the dominant factor limiting the ALD process at low temperatures.
21 July 2017 in Journal of Vacuum Science & Technology A
WKW. M. M. (Erwin) Kessels
The growth mechanism of the prototypical atomic layer deposition (ALD) process of Al2O3 using Al(CH3)3 (TMA) and H2O has been revisited on the basis of insights obtained with the nonlinear optical analysis technique of broadband sum-frequency generation (BB-SFG). With BB-SFG spectroscopy, both the –CH3 and –OH surface groups ruling the growth of Al2O3 by ALD were detected and could be monitored during the ALD process with submonolayer sensitivity. Several remaining questions pertaining to the growth mechanism of Al2O3 were addressed. The reaction kinetics of the H2O half-cycle were studied for ALD between 100 and 300 °C, and the reaction cross section σ was determined. The cross section at 300 °C was fairly large (σ = 3 × 10−19 cm2) and it decreased with decreasing temperature. Below 200 °C, the cross section also clearly varied with the surface coverage. For example, at 100 °C, the cross section started at σ = 1 × 10−20 cm2 for a full –CH3 coverage and decreased to σ = 3 × 10−21 cm2 for a 60% coverage. This coverage dependence of the reaction kinetics also explains the presence of the persistent –CH3 groups at low temperatures which are no longer reactive toward H2O. By a dedicated study using x-ray photo-emission spectroscopy, it was demonstrated that the persistent –CH3 groups were not incorporated into the film as a contaminant species. The absolute –CH3 coverage was measured for ALD between 100 and 450 °C. With this data, steric hindrance was ruled out as the cause of the self-limiting behavior in the TMA half-cycle on basis of the decrease observed in the –CH3 coverage with temperature. The self-limiting behavior was attributed to the depletion of under coordinated O during the TMA half-cycle. Moreover, the chemisorption of TMA on the -OH surface groups during the TMA half-cycle was investigated. On average, 1.5 –CH3 ligands remained on the surface per deposited Al atom after the TMA half-cycle at 300 °C, and this number decreased to 0.8 at 100 °C. These insights into the underlying growth mechanism augment the understanding of Al2O3 ALD and reveal several nuances in this well-studied ALD process.
23 September 2020 in ACS Applied Nano Materials
Extrinsically doped 2D semiconductors are essential for the fabrication of high-performance nanoelectronics amongst many other applications. Here we present a facile synthesis method for Al doped MoS2 via plasma-enhanced atomic-layer deposition (ALD) resulting in particularly sought-after p-type 2D material. Precise and accurate control over the carrier concentration was achieved over a wide range (1017 up to 1021 cm-3) while retaining good crystallinity, mobility, and stoichiometry. This ALD based approach also affords excellent control over the doping profile as demonstrated in a combined transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDX) study. Sharp transitions in the Al concentration were realized and both doped and undoped material had the characteristic 2D layered nature. The fine control over the doping concentration, combined with the conformallity and uniformity and sub-nm thickness control inherent to ALD should ensure compatibility with large scale fabrication. This makes Al:MoS2 ALD of interest for nanoelectronics but also for photovoltaics and TMD based catalysts.
15 November 2019 in Nanoscale
Texture has a significant impact on several key properties of transition-metal dichalcogenides (TMDs) films. Films with in-plane oriented grains have been successfully implemented in nano- and opto-electronic devices, whereas, films with out-of-plane oriented material have shown excellent performance in catalytic applications. It will be demonstrated that the texture of nanocrystalline TMD films can be determined with polarized Raman spectroscopy. A model describing the impact of texture on the Raman response of 2D-TMDs will be presented. For the specific case of MoS2, the model was used to quantify the impact of texture on the relative strength of the A1g and E1 2g modes in both the unpolarized and polarized Raman configuration. Subsequently, the capability to characterize texture by polarized Raman was demonstrated on various MoS2 films grown by atomic-layer deposition (ALD) and validated by complementary transmission electron microscopy (TEM) and synchrotron based 2D grazing-incidence X-ray diffraction (GIXD) measurements. This also revealed how the texture evolved during ALD growth of MoS2 and subsequent annealing of the films. The insights presented in this work allow a deeper understanding of Raman spectra of nanocrystalline TMDs and enable a rapid and non-destructive method to probe texture.
31 January 2022 in The Journal of Physical Chemistry C
A detailed understanding of the growth of noble metals by atomic layer deposition (ALD) is key for various applications of these materials in catalysis and nanoelectronics. The Pt ALD process using MeCpPtMe3 and O2 gas as reactants serves as a model system for the ALD processes of noble metals in general. The surface chemistry of this process was studied by in situ vibrational broadband sum-frequency generation (BB-SFG) spectroscopy, and the results are placed in the context of a literature overview of the reaction mechanism. The BB-SFG experiments provided direct evidence for the presence of CH3 groups on the Pt surface after precursor chemisorption at 250 °C. Strong evidence was found for the presence of a C═C containing complex (e.g., the form of Cp species) and for partial dehydrogenation of the surface species during the precursor half-cycle. The reaction kinetics of the precursor half-cycle were followed at 250 °C, showing that the C═C coverage saturated before the saturation of CH3. This complex behavior points to the competition of multiple surface reactions, also reflected in the temperature dependence of the reaction mechanism. The CH3 saturation coverage decreased significantly with temperature, while the C═C coverage remained constant after precursor chemisorption on the Pt surface for temperatures from 80 to 300 °C. These SFG results have resulted in a better understanding of the Pt ALD process and also highlight the surface chemistry during thin-film growth as a promising field of study for the BB-SFG community.