Bardia Hejazi

Bardia Hejazi

Auto-generated profile, based on publicly available information

Bardia Hejazi

Bundesanstalt für Materialforschung und -Prüfung (BAM, Federal Institute for Materials Research and Testing), Berlin, Germany

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 December 2021 in Proceedings of the National Academy of Sciences
Verified
Journal Article
Open access
PDF file
GBGholamhossein Bagheri
Gholamhossein Bagheri
BTBirte Thiede
Birte Thiede
BHBardia Hejazi
Bardia Hejazi
OSOliver Schlenczek
Oliver Schlenczek
EBEberhard Bodenschatz
Eberhard Bodenschatz
Significance: Wearing face masks and maintaining social distance are familiar to many people around the world during the ongoing SARS-CoV-2 pandemic. Evidence suggests that these are effective ways to reduce the risk of SARS-CoV-2 infection. However, it is not clear how exactly the risk of infection is affected by wearing a mask during close personal encounters or by social distancing without a mask. Our results show that face masks significantly reduce the risk of SARS-CoV-2 infection compared to social distancing. We find a very low risk of infection when everyone wears a face mask, even if it doesn’t fit perfectly on the face.

17 September 2019 in Experiments in Fluids
Verified
Journal Article
Closed access
PDF file
BHBardia Hejazi
Bardia Hejazi
MKMichael Krellenstein
Michael Krellenstein
GVGreg A. Voth
Greg A. Voth

26 October 2024 in Fatigue & Fracture of Engineering Materials & Structures
Verified
Journal Article
Open access
BHBardia Hejazi
Bardia Hejazi
ACAmaya Compart
Amaya Compart
TFTobias Fritsch
Tobias Fritsch
RWRuben Wagner
Ruben Wagner
Anja WeidnerAnja Weidner
Anja Weidner
GBGiovanni Bruno
Giovanni Bruno
X‐ray computed tomography (XCT) is extremely useful for the non‐destructive analysis of additively manufactured (AM) components. AM components often show manufacturing defects such as lack‐of‐fusion (LoF), which are detrimental to the fatigue life of components. To better understand how cracks initiate and propagate from internal defects, we fabricated Ti‐6Al‐4V samples with an internal cavity using electron beam powder bed fusion. The samples were tested in high‐cycle and very high‐cycle fatigue regimes. XCT was used to locate crack initiation sites and to determine characteristic properties of cracks and defects with the aid of deep learning segmentation. LoF defects exposed to the outer surface of the samples after machining were found to be as detrimental to fatigue life as the internal artificial defects. This work can benefit industries that utilize the AM of high‐strength, lightweight alloys, in the design and manufacturing of components to improve part reliability and fatigue life.

1 September 2023 in New Journal of Physics
Verified
Journal Article
Open access
PDF file
BHBardia Hejazi
Bardia Hejazi
HAHugo Antigny
Hugo Antigny
SHSophia Huellstrunk
Sophia Huellstrunk
EBEberhard Bodenschatz
Eberhard Bodenschatz
Animals and living organisms are continuously adapting to changes in their environment. How do animals, especially those that are critical to their ecosystem, respond to rapidly changing conditions in their environment? Here, we report on the three-dimensional trajectories of flying honeybees under calm and windy conditions in front of the hive entrance. We also investigate the pitch and yaw in our experiments. We find that the mean velocities, accelerations and angular velocities of honeybees increase with increasing wind speeds. We observed that pair separation between honeybees is highly controlled and independent of wind speeds. Our results on the coordination used by honeybees may have potential applications for coordinated flight of unmanned aerial vehicles.

1 November 2022 in New Journal of Physics
Verified
Journal Article
Open access
BHBardia Hejazi
Bardia Hejazi
CKChristian Küchler
Christian Küchler
GBGholamhossein Bagheri
Gholamhossein Bagheri
EBEberhard Bodenschatz
Eberhard Bodenschatz
In windy conditions, the air is turbulent. The strong and intermittent velocity variations of turbulence are invisible to flying animals. Nevertheless, flying animals, not much larger than the smallest scales of turbulence, manage to maneuver these highly fluctuating conditions quite well. Here we quantify honeybee flight with time-resolved three-dimensional tracking in calm conditions and controlled turbulent winds. We find that honeybee mean speed and acceleration are only weakly correlated with the strength of turbulence. In flight, honeybees accelerate slowly and decelerate rapidly, i.e., they break suddenly during turns and then accelerate again. While this behavior is observed in both calm and turbulent conditions, it is increasingly dominant under turbulent conditions where short straight trajectories are broken by turns and increased maneuvering. This flight-crash behavior is reminiscent of turbulence itself. Our observations may help the development of flight strategies for miniature flying robotics under turbulent conditions.

21 October 2025
Verified
Book Chapter
Open access
KCKeerthana Chand
Keerthana Chand
TFTobias Fritsch
Tobias Fritsch
BHBardia Hejazi
Bardia Hejazi
KPKonstantin Poka
Konstantin Poka
Giovanni BrunoGiovanni Bruno
Giovanni Bruno
Quality control in Additive Manufacturing (AM) is vital for industrial applications in areas such as the automotive, medical, and aerospace sectors. Geometric inaccuracies caused by shrinkage and deformations can compromise the life and performance of additively manufactured components. Such deviations can be quantified using Digital Volume Correlation (DVC), which compares the Computer-Aided Design (CAD) model with the X-ray Computed Tomography (XCT) geometry of the components produced. However, accurate registration between the two modalities is challenging due to the absence of a ground truth or reference deformation field. In addition, the extremely large data size of high-resolution XCT volumes makes computation difficult. In this work, we present a deep learning-based approach for estimating voxel-wise deformations between CAD and XCT volumes. Our method uses a dynamic patch-based processing strategy to handle high-resolution volumes. In addition to the Dice score, we introduce a Binary Difference Map (BDM) that quantifies voxel-wise mismatches between binarized CAD and XCT volumes to evaluate the accuracy of the registration. Our approach shows a 9.2% improvement in the Dice score and a 9.9% improvement in the voxel match rate compared to classic DVC methods, while reducing the interaction time from days to minutes. This work sets the foundation for deep learning-based DVC methods to generate compensation meshes that can then be used in closed-loop correlations during the AM production process. Such a system would be of great interest to industry, as it would make the manufacturing process more reliable and efficient, saving time and material.