Tian Chen
Auto-generated profile, based on publicly available information

Tian Chen

Department of Mechanical & Aerospace Engineering, University of Houston, Houston, USA

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 January 2021 in Nature
Verified
Journal Article
Closed access
PDF file
TCTian Chen
Tian Chen
MPMark V. Pauly
Mark V. Pauly
PRPedro M. Reis
Pedro M. Reis

15 May 2018 in Proceedings of the National Academy of Sciences
Verified
Journal Article
Closed access
PDF file
TCTian Chen
Tian Chen
OBOsama R. Bilal
Osama R. Bilal
KSKristina Shea
Kristina Shea
CDChiara Daraio
Chiara Daraio
Significance: A major challenge in soft robotics is the integration of sensing, actuation, control, and propulsion. Here, we propose a material-based approach for designing soft robots. We show an untethered, soft swimming robot, which can complete preprogrammed tasks without the need for electronics, controllers, or power sources on board. To achieve propulsion, we use bistable shape memory polymer muscles connected to paddles that amplify actuation forces. As a proof of principle, we show that these robots can be preprogrammed to follow specific routes or deliver a cargo and navigate back to their deployment point. The proposed design principle can have a broad impact in soft robotics based on programed materials.

28 June 2019 in Physical Review Applied
Verified
Journal Article
Open access
PDF file
TCTian Chen
Tian Chen
OBOsama R. Bilal
Osama R. Bilal
RLRobert Lang
Robert Lang
CDChiara Daraio
Chiara Daraio
KSKristina Shea
Kristina Shea
We introduce a metamaterial-based self-deployable system with a rotational periodicity. As a demonstration, we propose an autonomous solar panel array that is programmed to self-deploy in response to changes in the surrounding temperature. We achieve shape reconfiguration and structural stability by exploiting the physical properties in the constituting material and the architecture of the wedge-shaped unit cell. The unit cell consists of one arm of the elastic “flasher” origami and a pair of scissor mechanisms. First, kinematic analysis shows the difference between the theoretical behavior and behavior considering the physical dimensions. This is used to optimize the expansion ratio. Second, the deployment mechanics are enabled through the shape-memory effect inherent in the underlying polymer. A viscoelastic constitutive model is constructed to accurately predict the self-expanding behavior. Lastly, the collapsing and deployment dynamics are discussed. Bifurcation is observed during folding, leading to two different end states, a disk or a cone. By investigating the energy landscape of the system, an apparatus is introduced to enable the disk-shaped folding. A two-stage expansion is observed during deployment. The system first rotates and then expands radially. The resulting system is three-dimensionally (3D) printed, achieves an expansion ratio of 1000% in under 40 s, and shows excellent agreement with simulation prediction both in the collapsed and expanded configurations.

31 March 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
TCTian Chen
Tian Chen
JMJochen Mueller
Jochen Mueller
KSKristina Shea
Kristina Shea
Multi-material 3D printing has created new opportunities for fabricating deployable structures. We design reversible, deployable structures that are fabricated flat, have defined load bearing capacity, and multiple, predictable activated geometries. These structures are designed with a hierarchical framework where the proposed bistable actuator serves as the base building block. The actuator is designed to maximise its stroke length, with the expansion ratio approaching one when serially connected. The activation force of the actuator is parameterised through its joint material and joint length. Simulation and experimental results show that the bistability triggering force can be tuned between 0.5 and 5.0 N. Incorporating this bistable actuator, the first group of hierarchical designs demonstrate the deployment of space frame structures with a tetrahedron module consisting of three active edges, each containing four serially connected actuators. The second group shows the design of flat structures that assume either positive or negative Gaussian curvature once activated. By flipping the initial configuration of the unit actuators, structures such as a dome and an enclosure are demonstrated. A modified Dynamic Relaxation method is used to simulate all possible geometries of the hierarchical structures. Measured geometries differ by less than 5% compared to simulation results.

1 May 2019 in Extreme Mechanics Letters
Verified
Journal Article
Closed access
MWMarius A. Wagner
Marius A. Wagner
TLThomas S. Lumpe
Thomas S. Lumpe
TCTian Chen
Tian Chen
KSKristina Shea
Kristina Shea

1 September 2017 in 3D Printing and Additive Manufacturing
Verified
Journal Article
Closed access
MWMarius Wagner
Marius Wagner
TCTian Chen
Tian Chen
KSKristina Shea
Kristina Shea
Three-dimensional (3D) printing of active materials is a rapidly growing research area over the last few years. Numerous works have shown potential to revolutionize the field of four-dimensional (4D) printing and active self-deploying structures. Conventional manufacturing technologies restrict the geometric complexity of active structures. 3D printing allows the fabrication of complex active structures with no assembly required. In this study, we propose active 3D printed auxetic meta-materials that are capable of achieving area changes up to 200%. With these meta-materials, we design geometrically complex active structures that can be programmed into versatile shapes and recover their original shape given an external stimulus. We simulate the proposed meta-materials based on thermoviscoelastic material properties obtained by experimental characterization. A reduced beam model is constructed to predict forces and deformations of complex active structures. Excellent correlation is found between finite element simulation and experimental data from a 3-point bending test. Rectilinear tiling of the proposed meta-materials achieves the desired shape transformation. To demonstrate versatile programming, a selected meta-material is tiled into a complex contour, programmed into an arbitrary shape, and recovers as predicted. Simulation results verify this behavior. Such programmability in conjunction with 3D printing may be further exploited for applications such as biomedical devices, civil structures, and aerospace.