6 January 2022 in IEEE Transactions on Industrial Electronics
Conventional predictive position control (PPC) method balances the position, speed and current of permanent magnet synchronous machine with different weighting factors. However, tedious tuning work of weighting factors is needed. To simplify the tuning process, a cost function that includes the system position, and current information is constructed based on deadbeat control method. A novel method based voltage boundary is proposed to limit the current and speed simultaneously, the voltage regions corresponding to current and speed constraints are analyzed and the voltage duty cycle is further modified according to the voltage regions, the complex weighting factor turning work is avoided, the current and speed limits are easy to implement with proposed method and less position error can be achieved. Finally, the proposed method is experimentally compared with a conventional finite-control-set PPC method and a direct speed model predictive control method.
17 January 2023 in IEEE Transactions on Industrial Electronics
The system constraints (current, speed, and voltage limitations) are essential for the safety control of predictive position control (PPC) method. However, online solution of model predictive control with complex system constraints is still a challenge. In this article, a novel discrete-time model predictive position control (DMPPC) strategy for surface permanent magnet synchronous motor drive is proposed, the current, speed, and position are regulated simultaneously. The optimization model of the position control system considering system constraints is formulated, the current, speed, and voltage constraints are analyzed and transformed into the incremental voltage constraints. To reduce the calculation burden, a simplified method based on the geometric boundaries and cost function is proposed to solve the optimization problem, complex iterative calculations are avoided, the system constraints are well limited and less calculation time can be achieved. Finally, the proposed DMPPC method is experimentally verified and compared with a traditional iterative method and a cascade predictive position control (CPPC) method.
3 June 2024 in IEEE Transactions on Industrial Electronics
Predictive position control (PPC) method with long predictive horizon is an effective method to eliminate the cascade structure and improve the dynamic response for the permanent magnet synchronous motor (PMSM). However, traditional PPC method needs a time-consuming prediction process and does not always guarantee satisfactory position performance. In this article, a simplified constrained PPC method is proposed, the Laguerre functions are designed to construct the control trajectory of position system, which offers two control degrees to improve the position dynamic response and simplify programming of prediction process. Besides that, the optimization model with current constraints, speed constraints, and voltage constraints are constructed with the frame of Laguerre functions. The optimization model with constraints is solved with an optimal method and suboptimal method. The proposed PPC method is experimentally verified and compared with field-oriented control (FOC) method and a traditional PPC method, the results have proved that proposed method has excellent position performance and low calculation burden.
20 August 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
In this paper, a gain compensation-based quasi-resonant phase-locked loop (GCQR-PLL) with adaptive super-twisting sliding-mode observer (AST-SMO) is proposed. The conventional SMO typically employs a low-pass filter (LPF) and a quadrature phase-locked loop (QPLL) for position extraction. However, the tracking performance of the conventional QPLL is unsatisfactory, leading to position estimation error under transient conditions. Furthermore, the LPF fails to mitigate the DC disturbance caused by detection errors in the estimated backelectromotive force (EMF), resulting in position estimation error. To minimize the position estimation error, the proposed GCQR-PLL performs gain compensation under transient condition, which ensures sufficient bandwidth for position extraction, and at the same time, it effectively suppresses the DC disturbance due to detection error in estimated back-EMF by quasi-resonant (QR) structure. Additionally, the AST-SMO can diminish chattering at lower speeds while enhancing position estimation accuracy at higher speeds. The effectiveness of the proposed algorithm is verified under different operating conditions.
25 November 2025 in IEEE Transactions on Power Electronics
Sliding mode control (SMC) is widely used in the servo system of permanent magnet linear synchronous motor (PMLSM) and the problem of speed constraint exists in conventional sliding mode position controller (SMPC). The position speed integrated sliding mode controller (PSISMC) is an effective method to constrain speed for SMC due to its advantages of fast response and safety. However, the cascaded sliding mode surface structure of PSISMC makes the sliding mode surface design more complicated, and the low-speed crawling phenomenon in servo system of PMLSM may also affect the positioning accuracy. To handle these issues, a speed-constrained SMPC based on the control barrier function (CBF) is proposed in this article. By introducing CBF, the speed constraint is transformed into a constrained quadratic programming problem of q-axis current, achieving speed constraint while avoiding the use of cascaded sliding mode surfaces. A good speed constraining effect can be achieved by appropriately selecting the parameters of CBF. In addition, a new sliding mode reaching law consisting of the double power reaching law (DPRL) and a supertwisting-like integral term is proposed. Compared with the exponential reaching law in PSISMC, DPRL can alleviate the contradiction between sliding mode chattering and convergence speed. The supertwisting-like term is proposed and designed to alleviate the low-speed crawling phenomenon. Finally, experiments have demonstrated the advantages of CBF-SMC in positioning and tracking performance, as well as the effectiveness of its speed constraint capability.
4 June 2026 in IEEE Transactions on Industrial Electronics
Sliding mode control (SMC) is widely used in permanent magnet linear synchronous motor (PMLSM) servo systems. However, improving the antidisturbance performance of SMC requires increasing the control gain, and excessive gain may induce severe sliding mode chattering. To resolve this trade-off, this manuscript proposes an adaptive high-order supercritical sliding mode control (AHOSSMC) method for PMLSM servo systems. By integrating high-order sliding mode control (HOSMC) with an adaptive gain strategy based on control barrier function (CBF), the conflict between disturbance rejection and chattering suppression is effectively mitigated, and the friction force in the PMLSM servo system is better compensated. Both the high-order sliding mode algorithm and the adaptive law are improved to enhance the performance of the AHOSSMC. Moreover, the switching behavior of the adaptive law is explicitly addressed to ensure continuous variation of the adaptive gain. Finally, comprehensive experimental validation is conducted to demonstrate the superior position tracking performance of the proposed AHOSSMC.