Within this study, self-lubricating and triboactive (Cr,Al)N+Mo:S coatings were developed and investigated for the deposition on components in a low-temperature physical vapor deposition (PVD) hybrid process. Therefore, direct current magnetron sputtering (dcMS) and high power pulse magnetron sputtering (HPPMS) PVD were combined by using an industrial coating machine. Hereby, it was possible to deposit dense and smooth triboactive, self-lubricating nitride coatings with different chemical compositions and architectures on 16MnCr5E samples. Two coating architectures, a matrix monolayer and a graded coating structure, were developed to evaluate the effect on the tribological behavior. The morphology and coating thickness were analyzed by means of scanning electron microscopy (SEM). Furthermore, the indentation hardness and modulus of indentation as well as the compound adhesion between substrate materials and coating were analyzed. Tribological analyses of (Cr,Al)N+Mo:S-coated and uncoated samples were conducted under fluid-free friction regime at room temperature T = (20 ± 3) °C, a velocity v = 0.1 m/s and a distance s = 1000 m by varying the Hertzian contact pressure from 400 MPa ≤ pH ≤ 1300 MPa against steel counterparts, 100Cr6, in a pin-on-disk (PoD) tribometer. The graded coating architecture of (Cr,Al)N+Mo:S enabled a significant wear and friction reduction. Furthermore, Raman analyses prove the formation of solid lubrication tribofilm containing MoS2, MoO3 MoO2 and MoxOy at the toplayer of a graded (Cr,Al)N+Mo:S coating, which are responsible for the improved tribological behavior.
The purpose of this study was to increase the limited wear resistance of polymers in highly stressed tribological contacts. Therefore, diamond-like carbon (DLC) coatings were firstly developed and deposited on polymers. The development of the low temperature coating process was conducted on an industrial scale coating unit. Due to the use of polyether ether ether ketone (PEEK) and polyamide as substrate material, the coatings were tailored in accordance with different mechanical properties of the polymers. Furthermore, analyses regarding morphology, roughness as well as compound adhesion between coatings and polymers were conducted. The tribological analyses were accomplished for reciprocating sliding kinematics on pin-on-plate tribometer under dry conditions as well as boundary lubricated conditions. The results prove the ability of the coatings to undergo high plastic deformations without delamination. In addition, the possible formation of a composite layer of DLC and PEEK in the wear track due to high energy input under dry conditions was shown. Furthermore, the transformations of sp2 chain into ring bindings as well as a change of size and distribution of the sp2 clusters during dry contact conditions were observed.
The goal of this work is to evaluate the potential of diamond-like carbon (DLC) coatings on thermoplastic polymers for friction and wear reduction in highly stressed rolling–sliding contacts. Therefore, hydrogen-containing DLC coatings were deposited on the polymer surface by a low-temperature high power pulsed magnetron sputtering (HPPMS) physical vapor deposition (PVD) process. The rolling-sliding contact between coated polyamide 66 (PA66) or coated polyether ether ketone (PEEK) against case-hardened steel 16MnCr5 is investigated in a twin-disk tribometer at normal loads up to FN = 1,000 N, sum velocities between 1 m/s ≤ vΣ ≤ 16 m/s and slip ratios up to s = 50%. Results show a friction reduction with the application of DLC on the considered polymers compared to uncoated polymers under specific lubrication conditions. High solid losses caused by the polymer’s internal damping properties dominate the temperature behavior of the polymer, even when coated with DLC. Regarding the wear behavior, DLC coatings show potential especially under severe mixed lubrication conditions with high-solid load portion and sliding. The knowledge gained about coated polymers can be used to improve the overall tribological performance in terms of friction and wear of thermoplastic machine elements like gears.
20 July 2020 in Materialwissenschaft und Werkstofftechnik
Diamond‐like carbon (DLC) coatings are nowadays successfully applied on industrial components like pistons, piston rings and bearings in lubricated tribological contacts due to friction and wear reducing effects. In contradiction thereto, todays lubricants and additives are designed for tribological steel/steel contacts, whereby the knowledge on tribochemical layer formation on steel surfaces is comprehensive in contrast to the physical‐chemical interactions between diamond‐like carbon coatings, lubricants and additives. Therefore the formation mechanisms of zinc, molybdenum, sulfur and phosphorus containing reaction layers on a zirconium modified diamond‐like carbon coating a‐C : H : Zr (ZrCg) in lubricated tribological contacts were analyzed by means of pin‐on‐disc (PoD) tribometer by varying the distances from s = 200 m–3,000 m under boundary and mixed friction conditions at T = 90 °C and a contact pressure p = 1,300 MPa regarding the application of diamond‐like carbon coatings on gears. The base lubricant poly‐alpha‐olefin (PAO) was formulated using the anti‐wear (AW) and extreme pressure (EP) additive zinc dialkyldithiophosphate (ZnDTP) and the friction modifier (FM) additive molybdenum dialkyldithiophosphate (MoDTP). The chemical composition of the tribochemical reaction layers by means of and Raman spectroscopy and x‐ray photoelectron spectroscopy (XPS) as well as for the thickness differ significantly by varying the additivation.
Components running in fluid-free friction regimes are exposed to harsh conditions leading to increased friction and wear. Thereby, the use of the solid lubricant molybdenum disulfide (MoS2) via lacquers, powders or physical vapor deposition (PVD) coatings enables a friction and wear reduction. However, the tribological performance is limited to low mechanical loads. A promising coating concept already proven for high mechanical loads is the incorporation of the triboactive elements Mo and S in wear resistant hard nitride (Cr,Al)N matrix. In this study the supply mechanism and transfer of the tribofilm build out of the toplayer of the triboactive coating graded (Cr,Al)N + Mo:S under high mechanical loads at humid air were analyzed. Here, the chemical composition of the tribofilm was determined by a combination of Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) and correlated with tribological analysis. The results prove a friction and wear reduction independent of Hertzian pressure in the area of 400 MPa ≤ pH ≤ 1300 MPa due to the formation of a MoS2 and molybdenum oxide MoxOy containing tribofilm, whereby the share of MoxOy dominates compared to MoS2. Based on the results the understanding of the effect of the MoS2 + MoxOy containing tribofilm on the tribological behavior is increased.