Ufuk Tasci

Dr. Ufuk Tasci

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 June 2024 in Lubricants
Verified
Journal Article
Open access
PDF file
UTUfuk Tasci
Ufuk Tasci
TYTaha Alper YILMAZ
Taha Alper YILMAZ
HKHalil Karakoç
Halil Karakoç
SKSener Karabulut
Sener Karabulut
This study investigates the effect of graphene nanoplatelets (GNPs) and milling duration on the microstructure, mechanical properties, and wear resistance of the AA7020 alloy reinforced with Fe3O4 and GNP. The composites were prepared with a fixed 10 wt.% Fe3O4 and varying GNP contents (0.5 and 1 wt.%) using high-energy ball milling for 4 and 8 h, followed by hot pressing. The aim was to enhance the performance of the AA7020 alloy for potential use in defense, automotive, aviation, and space applications, where superior mechanical properties and wear resistance are required. The results showed that the incorporation of 0.5 wt.% GNP and optimized milling significantly improved the composite’s performance. The AA7020 + 10 wt.% Fe3O4 + 0.5 wt.% GNP composite achieved the highest density (99.70%) when milled for 4 h. Its hardness increased with both the inclusion of GNP and extended milling duration, with the composite milled for 8 h exhibiting the highest hardness value (149 HBN). The tensile strength also improved, with the composite milled for 4 h showing a 28% increase (292 MPa) compared with the unreinforced alloy. Additionally, the friction coefficient decreased with GNP content and milling duration, with the composite milled for 8 h showing a 26% reduction. Wear resistance was notably enhanced, with the composite milled for 8 h exhibiting the lowest specific wear rate (7.86 × 10−7 mm3/Nm).

29 May 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
UTUfuk Tasci
Ufuk Tasci
Hybrid B319 aluminum matrix composites reinforced with 10 wt% B4C and varying WS2 contents were fabricated to improve mechanical and tribological performance. The composite containing 2 wt% WS2 showed the best overall results, with a 29% increase in microhardness (104.3 HV) and a 20% improvement in transverse rupture strength (196.3 MPa) compared to unreinforced B319. Additionally, the friction coefficient dropped by 64% (from 0.497 to 0.178), and the specific wear rate was reduced to 4.34 × 10−6 mm3/N·m. Microstructural analyses confirmed homogeneous reinforcement distribution and adequate interfacial bonding. These enhancements are attributed to the dual action of B4C-induced strengthening and WS2-mediated tribo-film formation, offering a promising solution for lightweight, wear-resistant components in engineering applications.

15 December 2019 in International Advanced Researches and Engineering Journal
Verified
Journal Article
Open access
PDF file
HGHakan Gökmeşe
Hakan Gökmeşe
BBBulent Bostan
Bulent Bostan
TYTaha Alper YILMAZ
Taha Alper YILMAZ
UTUfuk Tasci
Ufuk Tasci
In this study, nanoparticle B4C synthesis was carried out by high-energy milling. For this purpose, B2O3-C-Mg triple systems were used in the reaction stoichiometric ratios as starting materials in the experimental studies. The reduction process of B2O3 was performed using speks type milling device. The transformation of the ceramic phase of the nanoparticle B4C by XRD analysis was examined. In terms of microstructural characterization of its powder shape and morphology, TEM (imaging and selected area diffraction pattern) investigations were conducted. The product synthesized by the leaching process was cleaned from MgO/B4C impurities and the production of the nanoparticle B4C was performed. After leaching processes, it was determined that some of the synthesized powders were below 50 nm, while others varied between the ranges of 50-350 nm. In TEM examinations of B4C particles carried out after leaching process, it was seen that there were twin formations observed as planar error. Depending on the d values calculated by solving the TEM diffraction patterns, the planes represented by nano-sized B4C particles were determined.


12 December 2025 in Tribology International
Verified
Journal Article
Closed access
UTUfuk Tasci
Ufuk Tasci
YÇYafes Çavuş
Yafes Çavuş
TYTaha Alper YILMAZ
Taha Alper YILMAZ
HKHalil Karakoç
Halil Karakoç
SKSener Karabulut
Sener Karabulut

13 September 2025 in Ceramics International
Verified
Journal Article
Closed access
MOMelika Ozer
Melika Ozer
GYGökçe Yaman
Gökçe Yaman
UTUfuk Tasci
Ufuk Tasci
HKHalil Karakoç
Halil Karakoç
AÖAlpay Özer
Alpay Özer
HCHanifi CINICI
Hanifi CINICI