Awais Ikram

Dr. Awais Ikram

Department for Management of Manufacturing Technologies, Faculty of Mechanical Engineering, University of Ljubljana, Ljubljana, Slovenia
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
JDJaka Dugar
Jaka Dugar
AIAwais Ikram
Awais Ikram
Damjan KlobčarDamjan Klobčar
Damjan Klobčar
FPFranci Pušavec
Franci Pušavec
Additive technologies enable the flexible production through scalable layer-by-layer fabrication of simple to intricate geometries. The existing 3D-printing technologies that use powders are often slow with controlling parameters that are difficult to optimize, restricted product sizes, and are relatively expensive (in terms of feedstock and processing). This paper presents the development of an alternative approach consisting of a CAD/CAM + combined wire arc additive-manufacturing (WAAM) hybrid process utilizing the robotic MIG-based weld surfacing and milling of the AlSi5 aluminum alloy, which achieves sustainably high productivity via structural alloys. The feasibility of this hybrid approach was analyzed on a representative turbine blade piece. SprutCAM suite was utilized to identify the hybrid-manufacturing parameters and virtually simulate the processes. This research provides comprehensive experimental data on the optimization of cold metal transfer (CMT)–WAAM parameters such as the welding speed, current/voltage, wire feed rate, wall thickness, torch inclination angle (shift/tilt comparison), and deposit height. The multi-axes tool orientation and robotic milling strategies, i.e., (a) the side surface from rotational one-way bottom-up and (b) the top surface in a rectangular orientation, were tested in virtual CAM environments and then adopted during the prototype fabrication to minimize the total fabrication time. The effect of several machining parameters and robotic stiffness (during WAAM + milling) were also investigated. The mean deviation for the test piece’s tolerance between the virtual processing and experimental fabrication was −0.76 mm (approx.) at a standard deviation of 0.22 mm assessed by 3D scanning. The surface roughness definition Sa in the final WAAM pass corresponds to 36 µm, which was lowered to 14.3 µm after milling, thus demonstrating a 55% improvement through the robotic comminution. The tensile testing at 0° and 90° orientations reported fracture strengths of 159 and 161.3 MPa, respectively, while the yield stress and reduced longitudinal (0°) elongations implied marginally better toughness along the WAAM deposition axes. The process sustainability factors of hybrid production were compared with Selective Laser Melting (SLM) in terms of the part size freedom, processing costs, and fabrication time with respect to tight design tolerances. The results deduced that this alternative hybrid-processing approach enables an economically viable, resource/energy feasible, and time-efficient method for the production of complex parts in contrast to the conventional additive technologies, i.e., SLM.

26 September 2018 in Journal of Alloys and Compounds
Verified
Journal Article
Open access
AIAwais Ikram
Awais Ikram
MMM. Farhan Mehmood
M. Farhan Mehmood
MPMateja Podlogar
Mateja Podlogar
AEAnas Eldosouky
Anas Eldosouky
RSRichard Sheridan
Richard Sheridan
KRKristina Žužek Rožman
Kristina Žužek Rožman
The goal of this study was to justify the reprocessing of recycled HDDR Nd-Fe-B powders with spark plasma sintering (SPS) and to investigate the dependence of the final magnetic properties on SPS and thermal treatment. The initial recycled HDDR powder of the composition Nd13.4Dy0.6Fe78.6B6.1Nb0.4Al0.7 with 4760 ppm O2 content, coercivity (HCi) = 830 kA/m, and large particle size distribution <50–600 μm, was treated using the SPS parameters as follows: T = 650–850 °C for 1–5 min and 50 MPa pressure. The post SPS thermal treatment was performed at 750 °C for 15 min in vacuum. The optimal SPS conditions at 750 °C for 1 min, yielded fully dense magnets with the coercivity HCi = 1060 kA/m, which was boosted to 1160 kA/m after the post-SPS thermal treatment. The grain growth was obvious in samples SPS-ed above 800 °C and subsequently, the HCi was reduced. The SPS reprocessing beyond 850 °C was found to be detrimental to the overall magnetic properties due to the formation of bimodal grain size distribution origination from the abnormal grain growth (700–2600 nm). The redistribution of Nd-rich grain boundary phase between the Nd2Fe14B matrix grains in thermally treated magnets and the relaxation of the internal stresses induced via SPS are the possible reasons for the HCi surpassing the HCi of the starting recycled HDDR powder. It was shown that the SPS consolidation technique is suitable for producing fully dense nanograined bulk Nd-Fe-B magnets, with coercivities even exceeding the initial HDDR-powder and is one of the most suitable routes for revitalizing the Nd-Fe-B scrap magnets.

1 January 2020 in Journal of Rare Earths
Verified
Journal Article
Open access
AIAwais Ikram
Awais Ikram
FMFarhan Mehmood
Farhan Mehmood
RSRichard Stuart Sheridan
Richard Stuart Sheridan
MAMuhammad Awais
Muhammad Awais
AWAllan Walton
Allan Walton
KRKristina Zuzek Rozman
Kristina Zuzek Rozman

3 July 2024 in Heliyon
Verified
Journal Article
Open access
MHMatija Hriberšek
Matija Hriberšek
SKSimon Kulovec
Simon Kulovec
AIAwais Ikram
Awais Ikram
MKMatjaž Kern
Matjaž Kern
LKLuka Kastelic
Luka Kastelic
FPFranci Pušavec
Franci Pušavec
Nowadays, this is even more challenging while additive manufacturing technology is used for prototyping, as well as the production of gearing systems. Presented is an optimization and characterization of the additively manufactured (AM) gears made of carbon-reinforced polyamide material in correlation to conventional polymer gearings. Based on the obtained results, the fatigue life data for AM carbon-reinforced Polyamide gears is calculated and compared to traditionally produced Polyamide 66-based gears. Results show that the durability of AM-produced carbon-reinforced Polyamide gears can be compared to conventional-produced Polyamide 66-based gears. Furthermore, deduced that wear of the AM-reinforced Polyamide teeth, can be closely connected with the meshing temperature in correlation with fatigue.

8 May 2019 in Materials
Verified
Journal Article
Open access
PDF file
AIAwais Ikram
Awais Ikram
MMM. Farhan Mehmood
M. Farhan Mehmood
ZSZoran Samardžija
Zoran Samardžija
RSRichard Sheridan
Richard Sheridan
MAMuhammad Awais
Muhammad Awais
KRKristina Zuzek Rozman
Kristina Zuzek Rozman
The magnetic properties of the recycled hydrogenation disproportionation desorption recombination (HDDR) Nd-Fe-B powder, doped with a low weight fraction of DyF3 nanoparticles, were investigated. Spark plasma sintering (SPS) was used to consolidate the recycled Nd-Fe-B powder blends containing 1, 2, and 5 wt.% of DyF3 grounded powder. Different post-SPS sintering thermal treatment conditions (600, 750, and 900 °C), for a varying amount of time, were studied in view of optimizing the magnetic properties and developing characteristic core-shell microstructure in the HDDR powder. As received, recycled HDDR powder has coercivity (HCi) of 830 kA/m, and as optimally as SPS magnets reach 1160 kA/m, after the thermal treatment. With only 1–2 wt.% blended DyF3, the HCi peaked to 1407 kA/m with the thermal treatment at 750 °C for 1 h. The obtained HCi values of the blend magnet is ~69.5% higher than the starting recycled HDDR powder and 17.5% higher than the SPS processed magnet annealed at 750 °C for 1 h. Prolonging the thermal treatment time to 6 h and temperature conditions above 900 °C was detrimental to the magnetic properties. About ~2 wt.% DyF3 dopant was suitable to develop a uniform core-shell microstructure in the HDDR Nd-Fe-B powder. The Nd-rich phase in the HDDR powder has a slightly different and fluorine rich composition i.e., Nd-O-F2 than in the one reported in sintered magnets (Nd-O-F). The composition of reaction zone-phases after the thermal treatment and Dy diffusion was DyF4, which is more abundant in 5 wt.% doped samples. Further doping above 2 wt.% DyF3 is ineffective in augmenting the coercivity of the recycled HDDR powder, due to the decomposition of the shell structure and formation of non-ferromagnetic rare earth-based complex intermetallic compounds. The DyF3 doping is a very effective single step route in a controlled coercivity improvement of the recycled HDDR Nd-Fe-B powder from the end of life magnetic products.

30 April 2018 in IEEE Magnetics Letters
Verified
Journal Article
Closed access
AEAnas Eldosouky
Anas Eldosouky
AIAwais Ikram
Awais Ikram
MMMuhammad Farhan Mehmood
Muhammad Farhan Mehmood
XXXuan Xu
Xuan Xu
SSSaso Sturm
Saso Sturm
ISIrena Skulj
Irena Skulj
The spark plasma sintering (SPS) technique is applied in combination with the hydrogen decrepitation process for the recycling of SmCo 5 magnets. The SmCo 5 magnets for recycling were first decrepitated by hydrogen gas at a pressure of 4 bar for 3 h to produce decrepitated powder. This powder was then used to prepare isotropic sintered magnets using the SPS technique by sintering at 800 °C-1000 °C for 1 min. Full densification of the SPS magnets was possible at a temperature of 1000 °C. The sample that was sintered at 900 °C showed the best internal coercivity ( i H c ) of higher than 1500 kA/m with a high remanence ( B r ) value of 0.47 T and energy product ( BH max ) of 43.4 kJ/m 3 . The properties of the SPS sample sintered at 900 °C are compared to the conventionally sintered (CVS) sample prepared by using fresh SmCo 5 powder. The results show an improvement in the magnetic properties of the SPS sample in comparison to the CVS sample at room temperature, and the possibility to use the SPS sample at a high temperature of 180 °C, where the sample showed good magnetic properties of i H c of 1502 kA/m, B r of 0.44 T, and BH max of 36.4 kJ/m 3 . Microstructure and X-ray diffraction patterns of the SPS and the CVS samples show that they consist of a SmCo 5 matrix with Sm 2 Co 7 and Sm oxides.