Intelligent connected vehicles (ICVs) have played an important role in improving the intelligence degree of transportation systems, and improving the trajectory prediction capability of ICVs is beneficial for traffic efficiency and safety. In this paper, a real-time trajectory prediction method based on vehicle-to-everything (V2X) communication is proposed for ICVs to improve the accuracy of their trajectory prediction. Firstly, this paper applies a Gaussian mixture probability hypothesis density (GM-PHD) model to construct the multidimension dataset of ICV states. Secondly, this paper adopts vehicular microscopic data with more dimensions, which is output by GM-PHD as the input of LSTM to ensure the consistency of the prediction results. Then, the signal light factor and Q-Learning algorithm were applied to improve the LSTM model, adding features in the spatial dimension to complement the temporal features used in the LSTM. When compared with the previous models, more consideration was given to the dynamic spatial environment. Finally, an intersection at Fushi Road in Shijingshan District, Beijing, was selected as the field test scenario. The final experimental results show that the GM-PHD model achieved an average error of 0.1181 m, which is a 44.05% reduction compared to the LiDAR-based model. Meanwhile, the error of the proposed model can reach 0.501 m. When compared to the social LSTM model, the prediction error was reduced by 29.43% under the average displacement error (ADE) metric. The proposed method can provide data support and an effective theoretical basis for decision systems to improve traffic safety.

It is agreed that connected vehicle technologies have broad implications to traffic management systems. In order to alleviate urban congestion and improve road capacity, this paper proposes a multilane spatiotemporal trajectory optimization method (MSTTOM) to reach full potential of connected vehicles by considering vehicular safety, traffic capacity, fuel efficiency, and driver comfort. In this MSTTOM, the dynamic characteristics of connected vehicles, the vehicular state vector, the optimized objective function, and the constraints are formulated. The method for solving the trajectory problem is optimized based on Pontryagin’s maximum principle and reinforcement learning (RL). A typical scenario of intersection with a one-way 4-lane section is measured, and the data within 24 hours are collected for tests. The results demonstrate that the proposed method can optimize the traffic flow by enhancing vehicle fuel efficiency by 32% and reducing pollutants emissions by 17% compared with the advanced glidepath prototype application (GPPA) scheme.

Integration technologies of artificial intelligence (AI) and autonomous vehicles play important roles in intelligent transportation systems (ITS). In order to achieve better logistics distribution efficiency, this paper proposes an intelligent actuator of an indoor logistics system by fusing multiple involved sensors. Firstly, an actuator based on a four-wheel differential chassis is equipped with sensors, including an RGB camera, a lidar and an indoor inertial navigation system, by which autonomous driving can be realized. Secondly, cross-floor positioning can be realized by multi-node simultaneous localization and mappings (SLAM) based on the Cartographer algorithm Thirdly the actuator can communicate with elevators and take the elevator to the designated delivery floor. Finally, a novel indoor route planning strategy is designed based on an A* algorithm and genetic algorithm (GA) and an actual building is tested as a scenario. The experimental results have shown that the actuator can model the indoor mapping and develop the optimal route effectively. At the same time, the actuator displays its superiority in detecting the dynamic obstacles and actively avoiding the collision in the indoor scenario. Through communicating with indoor elevators, the final delivery task can be completed accurately by autonomous driving.

Real-time and reliable short-term traffic state prediction is one of the most critical technologies in intelligent transportation systems (ITS). However, the traffic state is generally perceived by single sensor in existing studies, which is difficult to satisfy the requirement of real-time prediction in complex traffic networks. In this paper, a short-term traffic prediction model based on complex neural network is proposed under the environment of vehicle-to-everything (V2X) communication systems. Firstly, a traffic perception system of multi-source sensors based on V2X communication is proposed and designed. A mobile edge computing (MEC)-assisted architecture is then introduced in a V2X network to facilitate perceptual and computational abilities of the system. Moreover, the graph convolutional network (GCN), the gated recurrent unit (GRU), and the soft-attention mechanism are combined to extract spatiotemporal features of traffic state and integrate them for future prediction. Finally, an intelligent roadside test platform is demonstrated for perception and computation of real-time traffic state. The comparison experiments show that the proposed method can significantly improve the prediction accuracy by comparing with the existing neural network models, which consider one of the spatiotemporal features. In particular, for comparison results of the traffic state prediction and the error value of root mean squared error (RMSE) is reduced by 39.53%, which is the greatest reduction in error occurrences by comparing with the GCN and GRU models in 5, 10, 15 and 30 min respectively.

At present, the COVID-19 pandemic still presents with outbreaks occasionally, and pedestrians in public areas are at risk of being infected by the viruses. In order to reduce the risk of cross-infection, an advanced pedestrian state sensing method for automated patrol vehicles based on multi-sensor fusion is proposed to sense pedestrian state. Firstly, the pedestrian data output by the Euclidean clustering algorithm and the YOLO V4 network are obtained, and a decision-level fusion method is adopted to improve the accuracy of pedestrian detection. Then, combined with the pedestrian detection results, we calculate the crowd density distribution based on multi-layer fusion and estimate the crowd density in the scenario according to the density distribution. In addition, once the crowd aggregates, the body temperature of the aggregated crowd is detected by a thermal infrared camera. Finally, based on the proposed method, an experiment with an automated patrol vehicle is designed to verify the accuracy and feasibility. The experimental results have shown that the mean accuracy of pedestrian detection is increased by 17.1% compared with using a single sensor. The area of crowd aggregation is divided, and the mean error of the crowd density estimation is 3.74%. The maximum error between the body temperature detection results and thermometer measurement results is less than 0.8°, and the abnormal temperature targets can be determined in the scenario, which can provide an efficient advanced pedestrian state sensing technique for the prevention and control area of an epidemic.