Chaofeng Li

Dr. Chaofeng Li

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 July 2019 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
CPCheng Peng
Cheng Peng
ZCZhizhang (David) Chen
Zhizhang (David) Chen
Zhu LiuZhu Liu
Zhu Liu
JWJun-Feng Wang
Jun-Feng Wang
JLJingcheng Liang
Jingcheng Liang
JLJinyan Li
Jinyan Li
Research and development of wireless power transfer (WPT) systems has attracted much attention in recent years for their potential widespread applications. One of the much desirable features of a WPT system is load-independence. In this letter, we propose the insertion of a simple T-type network into a multi-receiver WPT magnetically coupled resonant WPT system to achieve the load-independence. We then present theoretical analysis, simulation, and experimental verifications; as a result, they lay the foundation for further investigations, improvements, and implementations of realistic WPT systems.

29 April 2019 in IEEE Internet of Things Journal
Verified
Journal Article
Closed access
HZHuapeng Zhao
Huapeng Zhao
CLChaofeng Li
Chaofeng Li
ZCZhizhang (David) Chen
Zhizhang (David) Chen
JHJun Hu
Jun Hu
Electrical Modeling of vehicular antennas is required for design of modern vehicle-to-everything communication networks. However, full-wave modeling and the existing equivalent source methods still ask for long computation time. To address this issue, a fast simulation method is proposed in this paper: a sparse equivalent source model is developed based on Huygens’ principle where a vehicular antenna is made equivalent to magnetic current placed on a finite conducting plate. The image theory and the uniform theory of diffraction are then applied, a modified Green’s function is derived, and the sparse equivalent source model is constructed to replace the original vehicular antenna. Because of its simple geometry and material, in comparisons with the existing methods, the proposed model uses significantly less expenditures for simulation of vehicular antennas while has better accuracy due to the consideration of the finite conducting plate. Simulations are performed to demonstrate the effectiveness and advantages of the proposed method, and a real-world experiment is designed and conducted to demonstrate the superiority of the proposed method with real measurement data. It is shown that the proposed method can save simulation time by four times, with less than 1 dB error compared to measurement.

18 April 2023 in IEEE Transactions on Signal and Power Integrity
Verified
Journal Article
Closed access
CLChaofeng Li
Chaofeng Li
KCKevin Cai
Kevin Cai
MOMuqi Ouyang
Muqi Ouyang
QGQian Gao
Qian Gao
BSBidyut Sen
Bidyut Sen
DKDongHyun Kim
DongHyun Kim
Via transitions in high-speed channels critically influence the signal integrity and power integrity of high-speed systems. In this work, a mode-decomposition-based equivalent model of a high-speed via that can be applied at frequencies up to 100 GHz is proposed for the first time. The equivalent model for modeling the via transition consists of upper and lower via-to-plate capacitances and equivalent parallel-plate impedances, owing to the fundamental mode and higher-order modes for parallel-plate, all of which can be calculated from physical geometrical parameters. The via-to-plate capacitances are calculated by using the domain decomposition method in the anti-pad domain and via domain. The parallel-plate impedances representing via and parallel-plate coupling are calculated with the mode decomposition method for different parallel-plate modes (fundamental and higher-order modes) in the parallel-plate domain. The proposed equivalent via model provides more accurate results in the high-frequency range than previously proposed methods. Because the impact of higher-order modes on parallel-plate impedance is considered in the proposed mode-decomposition-based via model, and the effects of higher-order modes are prominent at high frequencies for printed circuit board vias with typicaldimensions.The proposedmodel is validated with numerical examples, which show good correlation at frequencies as high as 100 GHz. The proposed model can be applied to high-speed via transitions in printed circuit boards and packages.

12 October 2022 in IEEE Transactions on Signal and Power Integrity
Verified
Journal Article
Closed access
YLYuanzhuo Liu
Yuanzhuo Liu
SYShaohui Yong
Shaohui Yong
YGYuandong Guo
Yuandong Guo
JHJiayi He
Jiayi He
CLChaofeng Li
Chaofeng Li
DKDongHyun Kim
DongHyun Kim
The difference in the dielectric permittivity of the different dielectric layers (including air) surrounding the microstrip is one of the major contributors to the far-end crosstalk (FEXT) in microstrip lines. The dielectric of the microstrip in printed circuit boards (PCBs) fabrication usually consists of two layers: the solder mask layer and the substrate layer. The characterization of the relative permittivity ( $\varepsilon_{r}$ ), dielectric dissipation factor (tanδ) for the dielectric layers of the microstrip are important parameters for board-level electronic system designs. In addition, the foil surface roughness cannot be ignored for the conductor loss modeling. In this work, an extraction method with high accuracy is proposed to characterize the dielectric material and foil surface roughness properties from the measured S-parameters with known cross-sectional geometry up to 20GHz. With the extracted properties, the FEXT and insertion loss of the microstrip can be estimated more accurately, providing design guidelines for PCB design and the material selection of the microstrip.

22 May 2023 in IEEE Transactions on Signal and Power Integrity
Verified
Journal Article
Closed access
YLYuanzhuo Liu
Yuanzhuo Liu
SBSiqi Bai
Siqi Bai
CLChaofeng Li
Chaofeng Li
VMVanine Sabino De Moura
Vanine Sabino De Moura
BCBichen Chen
Bichen Chen
DKDongHyun Kim
DongHyun Kim
To understand the skew in twinax cables of separately extrusion and co-extrusion design, the impact of inhomogeneous dielectric in copper twinax cables is analyzed, with an emphasis on signal integrity performance. The inhomogeneity is treated as a perturbation to the RLGC parameters, and analytical equations for calculation of scattering parameters from RLGC parameters are derived to analyze the effects of this perturbation on signal integrity. The inhomogeneity leads to a modulation behavior in the scattering parameters, which decreases asymmetry induced skew at high frequencies and eliminates the resonance of skew in the differential insertion loss. Mathematical analysis, the physical explanation, and various design cases are presented for validation.

16 May 2023 in IEEE Letters on Electromagnetic Compatibility Practice and Applications
Verified
Journal Article
Closed access
YLYuanzhuo Liu
Yuanzhuo Liu
YGYuandong Guo
Yuandong Guo
CLChaofeng Li
Chaofeng Li
XYXiaoning Ye
Xiaoning Ye
DKDonghyun Kim
Donghyun Kim
Microstrip line structures consist of different conductors, such as trace and reference planes, which have different surface roughness levels due to the printed circuit board manufacturing process. The bottom surface of the trace is often rougher than the top surface of the trace, and the roughness levels of different reference planes vary for different foil types and manufacturing processes. To accurately model the additional conductor loss caused by such differences in microstrip lines, a new modeling method is proposed with different roughness levels on different surfaces and a reference plane, in contrast to the traditional roughness modeling approach, which considers a uniform roughness distribution for all surfaces. The effect of the different surfaces on the resistance is determined by applying additional microstrip models to analyze the effect of surface roughness from different surfaces and to improve the accuracy of insertion loss prediction based on the modeled total resistance.