Gas bubbles are of major importance in most metallurgical processes. They promote chemical reactions, homogenize the melt, or float inclusions. Thus, their dynamics are of crucial interest for the optimization of metallurgical processes. In this work, the state of knowledge of bubble dynamics at the bubble scale in liquid metals is reviewed. Measurement methods, with emphasis on liquid metals, are presented, and difficulties and shortcomings are analyzed. The bubble formation mechanism at nozzles and purging plugs is discussed. The uncertainty regarding the prediction of the bubble size distribution in real processes is demonstrated using the example of the steel casting ladle. Finally, the state of knowledge on bubble deformation and interfacial forces is summarized and the scalability of existing correlations to liquid metals is critically discussed. It is shown that the dynamics of bubbles, especially in liquid metals, are far from understood. While the drag force can be predicted reasonably well, there are large uncertainties regarding the bubble size distribution, deformation, and lift force. In particular, the influence of contaminants, which cannot yet be quantified in real processes, complicates the discussion and the comparability of experimental measurements. Further open questions are discussed and possible solutions are proposed.
16 February 2021 in Metallurgical and Materials Transactions B
To account for increasing economic and ecological pressure, the steel industry is obligated to continuously optimize all processes. An important optimization approach is numerical modeling although its potential is limited by the accuracy of the mathematical models. In a previous work, a validation database was created and a validation score was derived from this data which allows a comprehensive qualitative accuracy assessment for those models. Here, this system is employed for a systematic optimization of the isothermal flow in the casting ladle. For that, different submodels, namely the turbulence models, subgrid turbulence models, bubble-induced turbulence and interfacial closure models as well as influencing factors, such as the grid resolution or the initial bubble size, are analyzed. It is shown that the large eddy turbulence model is more accurate than the Reynolds-average approach because it is able to reproduce the anisotropy of turbulence in the bubble region. In accordance with the literature, a grid dependency of the lift force is found which can be reduced using an averaged shear field as an additional variable. For the interfacial closure models, the combination of the Tomiyama drag model for fully contaminated systems and the Tomiyama lift correlation showed the best agreement with the experimental data. The results of the survey are summarized to a best-practice guideline with which the validation score can be increased from 38.7 with the Reynolds-average approach to 85.1 on a coarse grid respectively, and 87.8 on a fine grid. However, some upscaling problems of the numerical system from the water model to the real ladle are revealed. There is a need to find accurate yet efficient grid resolutions which make the large eddy turbulence model affordable with the current computational resources. Furthermore, alloying elements or non-metallic inclusions might alter the interfacial forces considerably. However, no studies on their effect have been published yet.
Improving the overall energy efficiency of processes is necessary to reduce costs, lower the specific energy consumption and thereby reduce the direct or indirect emission of gases that contribute to climate change. In many metallurgical processes, a large amount of energy is lost with the off-gas. In metallurgical recycling processes, off-gas often can be used to preheat the to-be-recycled metal scrap, leading to significantly higher energy efficiency. However, the application of preheating has the disadvantage that it often requires more precise planning in the design and better control of the process. In this paper, a simplified look at a continuously charged scrap preheating aggregate for the widely used electric arc furnace (EAF) in the steel processing industry is used as illustration. Continuous scrap charging in EAF-type furnaces in general has much higher demands on process control and general process knowledge, which is why they are found only very rarely. General issues and basic modeling approaches to mitigate such issues allowing a better process control will be described. In particular, a fast, one-dimensional modeling approach for the determination of the temperature distribution inside a constantly moving scrap bulk, with hot air (or exhaust gases) flowing through it, will be described. Possible modeling applications, assumptions, possible enhancements and limitations are shown. The first results indicate that this approach can be used as a solid basis for the modeling of scrap bulks with thermally thin parts, consisting of materials with similar thermodynamic material properties. Therefore, as a basis, this approach may help improve the design and control of future or existing preheating devices in metal recycling processes.
Calculating the radiation exchange between arbitrary surfaces using view factors is a common practice in the fields of industrial furnaces, climate modelling, solar power, thermal building design and so on. Here, a new model was developed to calculate the view factors of arbitrary two-dimensional geometries. This model is based on Hottel’s crossed strings method paired with an optimized algorithm to efficiently detect shadowing effects between the surfaces. The model’s accuracy and discretization dependency was tested against an analytical view factor calculation method using an example of two concentric, infinitely extended cylinders. The model can be applied to arbitrary linear discretized two-dimensional geometries. In particular, it guarantees the highest possible accuracy within the chosen discretization. The need for developing customized view factor equations of different two-dimensional geometries is therefore no longer necessary, since the convergence of the model with decreasing mesh size on analytical results can be demonstrated. Additionally, the performance and validity of the newly developed shadowing algorithm was tested against a common brute force approach and significant speedups were achieved. Furthermore, the additional application of the net radiation method for the calculation of the heat fluxes exchanged by radiation within those geometries is shown.
Electroslag remelting (ESR) is a well‐known process widely used in the production chain of high‐quality alloys. Herein, numerical investigations of the implementation of a rotating‐electrode (low rotation speed) modification to the flow behavior inside the slag area of a lab‐sized ESR process are shown. Therefore, a coupled simulation approach between a commercial CFD (FVM) and electromagnetics (FEM) software is used. Comparative results for the simulated droplet formation between a stationary and a rotating electrode are shown. The results show a strong effect on the local shaping of the liquid metal film below the electrode and consequently a radial shift of the droplet incidence into the metal pool under electrode rotation. There are no observable positive effects on mean metal film thickness, droplet trajectory, or droplet size, which are suspected as possible explanations for observed material improvements in small‐scale rotating electrode ESR processes. In addition, an overview of current bottlenecks, restrictions, and possible strategies for improved ESR process simulations is given.