Cindy Morales

Ms. Cindy Morales

Engineering Department, University of Ferrara, Ferrara, Emilia-Romagna, Italy
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 March 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Cindy MoralesCindy Morales
Cindy Morales
Mattia MerlinMattia Merlin
Mattia Merlin
Annalisa FortiniAnnalisa Fortini
Annalisa Fortini
AFAlessandro Fortunato
Alessandro Fortunato
Direct energy deposition (DED) is a widely accepted additive manufacturing process and a possible alternative to the subtractive manufacturing processes due to its high flexibility in fabricating new 3D parts. DED enables the manufacture of complex parts without using costly and time-consuming conventional processes, even though building parameters need to be accurately determined. In the present investigation, the effect of different process parameters on geometrical features, quality, microstructure, and microhardness of 17-4 PH stainless steel single tracks deposited onto an AISI 316L stainless steel substrate was investigated. Four sets of process parameters, considering different values of laser power, scanning speed, and powder feed rate, were selected in the manufacturing strategy, and specimens drawn from each single-track deposition were analyzed by stereomicroscopy, optical microscopy (OM), scanning electron microscopy (SEM-EDS), and X-ray diffraction (XRD). The results show that the optimized geometrical features of the track, together with the best microstructural and hardness properties, were obtained with the highest values of the laser energy input.

14 January 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Mattia MerlinMattia Merlin
Mattia Merlin
Cindy MoralesCindy Morales
Cindy Morales
Matteo FerroniMatteo Ferroni
Matteo Ferroni
Annalisa FortiniAnnalisa Fortini
Annalisa Fortini
Chiara SoffrittiChiara Soffritti
Chiara Soffritti
Post-fabrication heat treatment (PFHT) is one of the most applied strategies for achieving the desired microstructure and mechanical resistance on additive manufactured components because of the non-equilibrium microstructural state of the material in the as-built condition. In particular, during PFHT, 17-4 PH martensitic stainless steel is mainly strengthened by the precipitation of Cu-rich nanometric particles and Nb carbides into the metal matrix. In this work, the influence of specifically designed PFHTs on the microstructural and mechanical properties of 17-4 PH single tracks fabricated via direct energy deposition was studied. Different solubilization and aging times, as well as a direct aging strategy, were considered. Optical microscopy, X-ray diffractometry, and transmission electron microscopy were used to investigate the microstructure evolution induced by the PFHTs. Moreover, Vickers microhardness measurements were performed to evaluate the increase in mechanical strength. In all cases, the heat-treated single tracks showed a mean microhardness higher than that of the depositions in the as-built condition. In the single tracks subjected to solution treatment, followed by aging for about 100 h, the presence of both Cu-rich precipitates and Nb carbides was assessed; conversely, when directly aged from the as-built condition, only Nb carbides were detected. In the latter case, the carbides were finer and closer to each other than those in the single tracks aged after the solution treatment.

19 August 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Cindy MoralesCindy Morales
Cindy Morales
Annalisa FortiniAnnalisa Fortini
Annalisa Fortini
Chiara SoffrittiChiara Soffritti
Chiara Soffritti
Mattia MerlinMattia Merlin
Mattia Merlin
Laser-Directed Energy Deposition (L-DED) is an additive manufacturing technique that has lately been employed to deposit coatings of cemented carbides, such as WC-Co. During deposition, complex microstructural phenomena usually occur, strongly affecting the microstructural and mechanical behavior of the coatings. Post-fabrication heat treatments (PFHTs) may be applied to homogenize and strengthen the microstructure; nevertheless, to the best of the authors’ knowledge, just a few papers deepened the effect of these treatments on cemented carbides fabricated by additive manufacturing. This work evaluates the influence of four PFHTs on the microstructural evolution and hardness of L-DED WC-12Co. For each treatment, different combinations of solubilization time and temperature (between 30 and 180 min and from 400 °C to 700 °C, respectively) were adopted. The microstructure was investigated by optical and scanning electron microscopy equipped with energy-dispersive spectroscopy, whereas the mechanical properties were determined by Vickers hardness measurements. Based on the results, high microstructural heterogeneity in terms of WC particles, η-phase structures, and Co distribution was observed in the sample in the as-built condition. Some cracking defects were also observed in the samples, irrespective of the heat treatment conditions. Finally, a finer microstructure and a lower amount of brittle ternary η-phase, together with an increase in hardness (1030 ± 95 HV10), were found for the highest dwelling times (180 min) and for solubilization temperatures in the range of 500–600 °C.

7 September 2018 in Aircraft Engineering and Aerospace Technology
Verified
Journal Article
Closed access
Cindy MoralesCindy Morales
Cindy Morales
APArgelia Miranda Pérez
Argelia Miranda Pérez
GPGladys Yerania Pérez
Gladys Yerania Pérez
EHEduardo Hurtado
Eduardo Hurtado
Purpose: The purpose of this paper is to evaluate the welding quality of the friction stir joints of Al-SiC with diverse shape of pin geometry tools. Design/methodology/approach: Aluminum matrix composites are gaining unlimited interest and special position in aeronautical industry because of their properties enhanced by the presence of ceramic reinforcement, such as lower density, dimensional stability, exceptional wear and abrasion resistance. Friction stir welding arises as a promising welding process with more advantages than traditional fusion process in the joining of aeronautical components with the utilization of a non-consumable rotational tool shaped by a shoulder and a pin, which can be designed in as many possible geometries. However, the welding quality is not always achieved when varying these pin configurations. Findings: The fabrication and implementation of different pin geometry tools to weld the plates of the material allows to study the behavior of the joints assessing some discontinuities produced in the welds. Practical implications: To examine the microstructural evolution and its behavior in the different zones of the joint, the practical implication consists in the use of different characterization techniques like the optic microscopy and scanning microscopy, furthermore mechanical test such as the measurement of hardness. Originality/value: The study of the joints uses different welding tool geometries that were fabricated at prototype scale contribute in the microstructural analysis as well as in the evaluation of the possible discontinuities that are presented.

25 March 2022 in Fracture and Structural Integrity
Verified
Journal Article
Open access
PDF file
Cindy MoralesCindy Morales
Cindy Morales
Mattia MerlinMattia Merlin
Mattia Merlin
Annalisa FortiniAnnalisa Fortini
Annalisa Fortini
GGGian Luca Garagnani
Gian Luca Garagnani
APArgelia Miranda Pérez
Argelia Miranda Pérez
Dissimilar friction stir welding joints are widely employed in the industrial field due to the excellent microstructural and mechanical properties of the resulting joints. Nevertheless, to further enhance the weld properties, the addition of reinforcement particles on the joint-line during the process has been proven effective for increasing its mechanical performance. In the present investigation, the microstructure and the impact behaviour of FSWed joints between AA2024-T351 and AA7075-T651 aluminium plates were investigated, considering the effect of different process parameters selected through a full factorial 2k design of experiments: both the rotational and translational speed of the tool, as well as the addition of Al2O3-SiC microparticles, were considered as input parameters. Unnotched 10 x 5 x 55 mm impact specimens were tested through an instrumented 50 J Charpy pendulum: total impact energy, the two complementary initiation and propagation energies as well as the peak force were correlated to the adopted process parameters. From the performed analyses, it was found that joints with reinforcing particles are prone to form wormhole defects across the stir zone that not only affect the microstructural development, but also the impact behaviour since they require less energy at break in comparison with joints fabricated without particles addition.

16 September 2019 in MRS Advances
Verified
Journal Article
Closed access
PDF file
JAJorge L. Acevedo
Jorge L. Acevedo
Cindy MoralesCindy Morales
Cindy Morales
BRBryan R. Rodriguez
Bryan R. Rodriguez
PCPaola B. Cerna
Paola B. Cerna