When two compatible polymer melts are brought into contact, a diffuse interphase is formed that governs the adhesion between them. The degree of interdiffusion is defined mainly by the processing conditions and the physico‐chemical properties of the materials. Despite the great industrial relevance of co‐extrusion in manufacturing multilayer structures, little research has dealt with interdiffusion under these processing conditions, where polymer‐polymer interfaces are subject to shear load. In this work, procedures for investigating interdiffusion both under static and real co‐extrusion flow conditions were developed. Using various grades of poly(methyl methacrylate) and styrene‐co‐acrylonitrile copolymer, we studied both theoretically and experimentally the effects of interfacial contact time, temperature, material compatibility, and interfacial shear stress on interdiffusion. Spectroscopic analysis of the interfaces using confocal Raman microscopy showed that the general relationships between interdiffusion, time (Fick's law) and temperature (Arrhenius relationship) are identical under both static and co‐extrusion conditions. However, the interdiffusion rate is significantly higher under shear influence. Since the prediction of the interdiffusion process supports material selection and process design in multilayer manufacturing, a simple analytical model was developed to quantify the effects of aforementioned material properties and processing conditions on the apparent mutual interdiffusion coefficient.
Co-extrusion is commonly used to produce polymer multilayer products with different materials tailoring the property profiles. Adhesion between the individual layers is crucial to the overall performance of the final structure. Layer adhesion is determined by the compatibility of the polymers at the interface and their interaction forces, causing for example the formation of adhesive or chemical bonds or an interdiffusion layer. Additionally, the processing conditions, such as temperature, residence time, cooling rate, and interfacial shear stress, have a major influence on the interactions and hence resulting layer adhesion. Influences of temperature and residence time are already quite well studied, but influence of shear load on the formation of an adhesion layer is less explored and controversially discussed in existing literature. In this work, we investigated the influence of different processing conditions causing various shear loads on layer adhesion for a two-layer co-extruded polymer sheet using a polypropylene and polypropylene talc compound system. Therefore, we varied the flow rates and the flow geometry of the die. Under specific conditions interfacial flow instabilities are triggered that form micro layers in the transition regime between the two layers causing a major increase in layer adhesion. This structure was analyzed using confocal Raman microscopy. Making use of these interfacial flow instabilities in a controlled way enables completely new opportunities and potentials for multi-layer products.
Layered van der Waals semimetallic -WTe, exhibiting intriguing properties which include non-saturating extreme positive magnetoresistance (MR) and tunable chiral anomaly, has emerged as a model topological type-II Weyl semimetal system. Here, ∼45 nm thick mechanically exfoliated flakes of -WTe are studied via atomic force microscopy, Raman spectroscopy, low-T/high- magnetotransport measurements and optical reflectivity. The contribution of anisotropy of the Fermi liquid state to the origin of the large positive transverse and the signature of chiral anomaly of the type-II Weyl Fermions are reported. The samples are found to be stable in air and no oxidation or degradation of the electronic properties is observed. A transverse ∼1200 % and an average carrier mobility of 5000 cmVs at for an applied perpendicular field are established. The system follows a Fermi liquid model for and the anisotropy of the Fermi surface is concluded to be at the origin of the observed positive MR. Optical reflectivity measurements confirm the anisotropy of the electronic behaviour. The relative orientation of the crystal axes and of the applied electric and magnetic fields is proven to determine the observed chiral anomaly in the in-plane magnetotransport. The observed chiral anomaly in the WTe flakes is found to persist up to , a temperature at least four times higher than the ones reported to date.
In polymer multilayer materials, the adhesion between the individual layers is an essential feature governing the overall product quality. For compatible polyme
About Me
PhD student at Johannes Kepler University Linz - Institute of Polymer Science
PhD student at Johannes Kepler University Linz - Institute of Polymer Science