Whilst the physics of both classical evaporation and supercritical fluid mixing are reasonably well characterized and understood in isolation, little is known about the transition from one to the other in the context of liquid fuel systems. The lack of experimental data for microscopic droplets at realistic operating conditions impedes the development of phenomenological and numerical models. To address this issue we performed systematic measurements using high-speed long-distance microscopy, for three single-component fuels (n-heptane, n-dodecane, n-hexadecane), into gas at elevated temperatures (700-1200 K) and pressures (2-11 MPa). We describe these high-speed visualizations and the time evolution of the transition from liquid droplet to fuel vapour at the microscopic level. The measurements show that the classical atomization and vaporisation processes do shift to one where surface tension forces diminish with increasing pressure and temperature, but the transition to diffusive mixing does not occur instantaneously when the fuel enters the chamber. Rather, subcritical liquid structures exhibit surface tension in the near-nozzle region and then, after time surrounded by the hot ambient gas and fuel vapour, undergo a transition to a dense miscible fluid. Although there was clear evidence of surface tension and primary atomization for n-dodecane and n-hexadecane for a period of time at all the above conditions, n-heptane appeared to produce a supercritical fluid from the nozzle outlet when injected at the most elevated conditions (1200 K, 10 MPa). This demonstrates that the time taken by a droplet to transition to diffusive mixing depends on the pressure and temperature of the gas surrounding the droplet as well as the fuel properties. We summarise our observations into a phenomenological model which describes the morphological evolution and transition of microscopic droplets from classical evaporation through a transitional mixing regime and towards diffusive mixing, as a function of operating conditions. We provide criteria for these regime transitions as reduced pressure–temperature correlations, revealing the conditions where transcritical mixing is important to diesel fuel spray mixing
Detailed measurements of near-nozzle spray formation are essential to better understand and predict the physical processes involved in diesel fuel atomisation. We used long-range microscopy to investigate the primary atomisation of diesel, biodiesel and kerosene fuels in the near-nozzle region, both at atmospheric and realistic engine conditions. High spatial and temporal resolutions allowed a detailed observation of the very emergence of fuel from the nozzle orifice. The fluid that first exited the nozzle resembled mushroom-like structures, as occasionally reported by other researchers for atmospheric conditions, with evidence of interfacial shearing instabilities and stagnation points. We captured the dynamics of this phenomenon using an ultra-fast framing camera with frame rates up to 5 million images per second, and identified these structures as residual fluid trapped in the orifice between injections. The residual fluid has an internal vortex ring motion which results in a slipstream effect that can propel a microscopic ligament of liquid fuel ahead. We showed that this mechanism is not limited to laboratory setups, and that it occurs for diesel fuels injected at engine-like conditions with production injectors. Our findings confirm that fuel can remain trapped in the injector holes after the end of injection. Although we could not measure the hydrocarbon content of the trapped vapourised fluid, we observed that its density was lower than that of the liquid fuel, but higher than that of the in-cylinder gas. We conclude that high-fidelity numerical models should not assume in their initial conditions that the sac and orifices of fuel injectors are filled with in-cylinder gas. Instead, our observations suggest that the nozzle holes should be considered partially filled with a dense fluid
1 November 2007 in Energy Conversion and Management
In this paper a breakup model for analysing the evolution of transient fuel sprays characterised by a coherent liquid core emerging from the injection nozzle, throughout the injection process, is proposed. The coherent liquid core is modelled as a liquid jet and a breakup model is formulated. The spray breakup is described using a composite model that separately addresses the disintegration of the liquid core into droplets and their further aerodynamic breakup. The jet breakup model uses the results of hydrodynamic stability theory to define the breakup length of the jet, and downstream of this point, the spray breakup process is modelled for droplets only. The composite breakup model is incorporated into the KIVA II Computational Fluid Dynamics (CFD) code and its results are compared with existing breakup models, including the classic WAVE model and a previously developed composite WAVE model (modified WAVE model) and in-house experimental observations of transient Diesel fuel sprays.The hydrodynamic stability results used in both the jet breakup model and the WAVE droplet breakup model are also investigated. A new velocity profile is considered for these models which consists of a jet with a linear shear layer in the gas phase surrounding the liquid core to model the effect of a viscous gas on the breakup process. This velocity profile changes the driving instability mechanism of the jet from a surface tension driven instability for the currently used plug flow jet with no shear layers, to an instability driven by the thickness of the shear layer. In particular, it is shown that appreciation of the shear layer instability mechanism in the composite model allows larger droplets to be predicted at jet breakup, and gives droplet sizes which are more consistent with the experimental observations. The inclusion of the shear layer into the jet velocity profile is supported by previous experimental studies, and further extends the inviscid flow theory used in the formulation of the classic WAVE breakup model