In this study, geopolymers made of metakaolin (MK), diatomite (D), and rice husk ash (RHA) were developed for ceiling thermal insulation in houses to provide protection against cold temperatures. The influence of the constituent mixing ratio and the temperature of curing on the heat conductivity and compressive strength of the geopolymer was investigated. Specimens were formed according to a 10-level mix design with three replicates and subjected to curing at 40 °C and 80 °C. Heat conductivity and compressive strength were determined in accordance with established standards. The simplex lattice method was used to obtain the response surfaces, contour plots, and tracking curves. The geopolymers under study displayed a reduction in heat conductivity and an increase in compressive strength when the curing temperature was raised. The optimal mixing ratio to achieve a balance between the compressive strength and thermal conductivity of the geopolymers investigated was 0.50 MK and 0.50 RHA. Diatomite’s thermal insulation contribution is neutralized when crystals from the geopolymer gel fill the pore volume. The mixture’s optimal results were achieved when cured at 80 °C, demonstrating a thermal conductivity of 0.10 W/m·K and a compressive strength of 5.37 MPa.
This study investigates how rice husk ash (RHA) content and particle size influence the water susceptibility of asphalt mixes. A two-factor experiment was conducted, varying RHA proportions (2.5%, 5.0%, and 7.5%) and particle sizes (149, 74, and 53 µm). The RHA, sourced from agro-industrial wastes in Trujillo, Peru, was previously analyzed by, scanning electron microscopy (SEM) showed irregular, porous, and angular particles, typical of ashes produced at moderate temperatures, which enhance binder interaction and internal friction. The ash analysis also identified crystalline phases like cristobalite and quartz, suggesting chemical reactivity. Coarse and fine aggregates met Peruvian standards for durability and wear resistance. The optimal asphalt cement content was 4.39%, balancing cohesion, stability, and air voids. The experimental results indicate that adding 5.0% RHA, especially with particle sizes smaller than 53 µm, significantly improves the mixture's resistance to moisture damage. This not only enhances the longevity of pavements but also promotes sustainability by incorporating waste materials into road construction. The incorporation of RHA not only improves the technical performance of asphalt mixtures, but also represents an environmentally beneficial strategy by reusing an abundant agricultural waste, reducing the environmental impact and promoting a circular economy.
In this study, the concentration and proportion of nopal cactus were modified to analyze the clarification, turbidity, suspended solids and pH of irrigation water. The levels investigated for the concentration of nopal cactus were 30 and 40 mg/L and for the ratio of the natural coagulant to aluminum sulfate were 10/90, 30/70 and 50/50. The population was constituted by water from the Moche River located in the province of Trujillo, which has an approximate flow of 8.8 m 3 /s in summer time and the sample was collected near the district of Moche in a strategic point, it was 80 liters. The results show that the turbidity decreases with the proportion and concentration of the coagulant, as well as the total suspended solids, the pH was stabilized, achieving the highest coagulant efficiency of 96.3% at a concentration of 30 mg/L and a proportion of 30% natural coagulant with 70% aluminum sulfate, this being the appropriate dosage that shows the best results.
The objective of this research was to determine the influence of the percentage of hydroxyapatite (HA) on impact strength, adhesive wear and shore hardness in biocomposites based on high-density polyethylene (HDPE). HA was obtained from eggshells after grinding, phosphating and calcination processes. The HDPE-HA biocomposites were manufactured by single-screw extrusion process, L/D: 20 to 0%, 10%, 20%, 30% and 40% weight of HA in a temperature range of 230-240°C. Characterization by Fourier transform infrared spectroscopy, thermogravimetric analysis, and X-ray diffraction confirmed the formation of HA. The best results of the mechanical properties studied were presented in biocomposites with 20% HA, achieving an impact strength of 23.10 KJ/m 2 , an adhesive wear in terms of mass loss of 0.367g and a hardness of 19.77 Shore D. The research concludes that the addition of HA improves the properties of impact strength, adhesive wear and shore hardness in biocomposites with HDPE matrix, with 20% HA being the optimal addition percentage.
In this work, fruit waste was used as a source of raw material to produce biodegradable materials. Starch was extracted from avocado seeds (Persea Americana Mill) and cellulose from pineapple crowns (Ananas comosus) to produce biofilms. The research focused on studying the effect of the percentage of microcellulose and plasticizer on the tensile strength, deformation and rigidity of biofilms based on modified starch reinforced with cellulose microfibers (45, 50 and 55%;). Starch and cellulose were extracted by wet extraction and treatments (alkaline and acid), respectively. The shaping method used for the biofilms was solution fusion and glycerin was used as a plasticizer at doses of 20, 25 and 30%. The results showed maximum tensile strength and stiffness values of 12.1 MPa and 54.1 MPa respectively; in films reinforced with 55% cellulose and plasticized with 20% glycerin, although the maximum percentage deformation (42.6%) was reached in biofilms with 50% cellulose and 25% glycerin. Meanwhile, the lowest tensile strength values (7.2 MPa) were achieved with 45% cellulose and 30% glycerin, while the lowest stiffness (18.6 MPa) was achieved with 50% cellulose and 25 % glycerin, and the minimum deformation was 22% with 45% cellulose and 20% glycerin. It was concluded that as the weight percentage of cellulose increases up to 55% in the biofilms, the average values of tensile strength and stiffness increase, On the contrary, as the weight percentage of glycerin increases up to 25%, the tensile strength and rigidity decrease; Regarding the percentage deformation of the biofilms, they presented an inverse effect. This study aimed to expand research on biofilms used as biodegradable packaging.
In this study, the type of deflocculant and the proportion of iron oxide are modified to analyze the color using the CIELab model and the water absorption of the engobe-coated ceramics. The levels investigated for iron oxide were 2.5, 5, and 10%, and for the type of deflocculant: sodium silicate, sodium carbonate, and sodium hexametaphosphate. To establish the optimum percentage of the dispersion agent, deflocculation curves were created, with results of 0.44% for sodium silicate, 0.15% for sodium carbonate, and 0.22% for sodium hexametaphosphate. Engobes were made in an alumina ball mill with a mixing time of 15 minutes. The supports were dip-coated; each support received three layers of coating that were immersed for no more than three seconds. The dried engobed tesserae were fired at 950°C after one week of drying. Color was measured using ASTM D 2244, and the percentage of water absorption was determined using ASTM C 373. The results show that the saturation of the engobes increases with the percentage of iron oxide, but not with brightness, hue, or absorption, which decrease. In addition, sodium silicate shows the most promising results as a deflocculant because it disperses more fine particles on the surface, improving color parameters and decreasing water absorption.