Fazel Pourmirzaei Deylami

Dr. Fazel Pourmirzaei Deylami

Faculty of Electrical Engineering, Shahrood University of Technology, Īrānshahr, Sīstān va Balūchestān, Iran
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 May 2023 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
MRMahdie Rahmani
Mahdie Rahmani
ADAhmad Darabi
Ahmad Darabi
Fazel Pourmirzaei DeylamiFazel Pourmirzaei Deylami
Fazel Pourmirzaei Deylami
In this article, the rate of acceleration, speed, and displacement of electric motor structure particles in response to radial electromagnetic forces is studied in detail. For this purpose, the vibrations and acoustic noise of three similar induction motors are investigated by changing the stator winding pitch through finite element modeling (FEM) by conducting electromagnetic, structural, and frequency analyses. Three similar induction motors with 24 slots in the stator are selected, two motors are wound with a shorted pitch by 2 and 1 slot, respectively, and the third motor's winding is considered full pitch winding. The simulation results are validated by experimental measurements of the amount of acoustic noise and vibrations of three motors. The results of the simulations and experimental measurements are in good agreement and indicate less noise and vibrations in the first induction motor with two short slots in the stator winding pitch.

19 December 2022 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
Fazel Pourmirzaei DeylamiFazel Pourmirzaei Deylami
Fazel Pourmirzaei Deylami
ADAhmad Darabi
Ahmad Darabi
FAFarshad Asadi
Farshad Asadi
AGArash Gharavi
Arash Gharavi
In order to improve the performance of synchronous motors, especially in dynamic-transient conditions, induction damper cages are usually used in the rotor structure. In this paper, a new hybrid structure of an axial-flux motor is proposed, which uses a permanent magnet (PM) rotor and an unpaired induction damper cage with independent movement capability. The proposed motor design procedure is provided in some detail. The performance of the proposed motor is evaluated using the finite element method (FEM) simulation and the operational effects of the unpaired damper cage are evaluated. In addition, comparisons were made between three different motor structures including the structure without damper cage (WDC), the structure equipped with coupled damper cage (CDC), and the structure equipped with unpaired damper cage (UDC) (proposed structure). Dynamic-transient and steady-state characteristics of motors including current profile, torque, and speed are evaluated. In order to confirm the results of the FEM simulations, a prototype of the proposed motor is manufactured, and some functional tests were performed on it. The results show that the proposed new structure can have better dynamic performance than other structures in terms of the amplitude of fluctuations as well as the time to reach the steady-state.

23 February 2022
Verified
Conference Paper
Closed access
Fazel Pourmirzaei DeylamiFazel Pourmirzaei Deylami
Fazel Pourmirzaei Deylami
ADAhmad Darabi
Ahmad Darabi
Doubly-fed induction machines (DFIMs) are widely used as wind generators. However, these machines can also be used in motor mode as electric propulsion systems in electric vehicles. This paper presents a detailed steady-state analysis of a DFIM. In this study, using the per-phase equivalent circuits and steady-state equations, a comprehensive analysis of the DFIM in motor operation mode is presented. The behavior of the motor in all three synchronous, super-synchronous, and sub-synchronous modes is analyzed and evaluated using the simulation results. Adjusting and controlling the rotor voltage is very essential. Therefore, a simple method for optimally adjusting the amplitude and angle of the rotor voltage is proposed for two different optimization scenarios that maximize output power and efficiency, respectively. According to the results, if the rotor voltage is properly selected, the DFIM can operate optimally at a wide range of speeds.

3 June 2023 in IET Electric Power Applications
Verified
Journal Article
Open access
PSPoria Soheili
Poria Soheili
ADAhmad Darabi
Ahmad Darabi
Fazel Pourmirzaei DeylamiFazel Pourmirzaei Deylami
Fazel Pourmirzaei Deylami
A two‐degrees‐of‐freedom (2DOF) dual‐rotor axial‐flux induction motor (2DOF‐DRAFIM) is proposed with independent movement capability of rotors and its performance is evaluated in detail. First, using the analytical equations, the steady‐state model of the motor is presented and the electrical equivalent circuit is extracted along with an electromagnetic design algorithm for the proposed motor. In the next step, using two‐dimensional and three‐dimensional finite element modelling (FEM), the performance of the proposed motor is investigated. The results of the experimental measurements on the manufactured prototype confirm the validity of the results of theoretical modelling and finite element simulations. The proposed structure provides some unique features. One of the fascinating behaviours of the proposed 2DOF‐DRAFIM is that the higher‐speed rotor produces higher output torque and the lower‐speed rotor has lower torque. In this regard, the 2DOF structure can be considered a potential concept for electric vehicles (EVs) without needing a conventional mechanical differential.

1 January 2024 in IET Electrical Systems in Transportation
Verified
Journal Article
Open access
PDF file
AHAlireza Hesari
Alireza Hesari
ADAhmad Darabi
Ahmad Darabi
Fazel Pourmirzaei DeylamiFazel Pourmirzaei Deylami
Fazel Pourmirzaei Deylami
This article proposes a dual independent rotor axial flux induction motor (DIR‐AFIM) with two degrees of freedom as a propulsion motor for an electric vehicle (EV). The performance of this motor in different operating conditions of the vehicle is discussed and investigated. This motor has two rotors that are mechanically independent of each other, providing driving force for the EV separately and enabling the removal of any mechanical or electrical differential. The propulsion motor can play the role of differential and also reduce the cost and complexity of the entire propulsion system in some extent. The finite element modeling of the proposed motor has been performed and the performance characteristics have been evaluated in three operating scenarios: flat path, sloped path, and turning path, taking into account the dynamics of the vehicle. Additionally, the accuracy of the simulations and modeling has been confirmed by performing some practical tests on the prototype machine. The results show that the simulations and measurements are in good agreement and the proposed propulsion system can be a suitable option for lightweight electric vehicles.

6 March 2021 in IET Electric Power Applications
Verified
Journal Article
Open access
PDF file
Fazel Pourmirzaei DeylamiFazel Pourmirzaei Deylami
Fazel Pourmirzaei Deylami
ADAhmad Darabi
Ahmad Darabi
This article describes a detailed analytical method for obtaining the capacitance matrix elements in variable capacitance synchronous machines (VCSMs). The analytical modelling approach is performed by introducing a decentralized sinusoidal distribution of the stator/rotor electrodes and involves obtaining the capacitance matrix elements based on the electro motive force distribution in the air gap and calculating the induced electric charge in the stator/rotor electrode surfaces. The proposed analytical formulas are valid for both radial‐field and axial‐field VCSM structures. The analytical model is evaluated and well verified through analysing a multi‐stack axial‐field VCSM using 3D finite element simulation. Furthermore, a prototype of the VCSM is manufactured and tested to validate the results obtained from the proposed analytical model and finite element method simulations. Based on the results, the proposed model and analytical formulas are able to accurately estimate the capacitance matrix elements of the VCSMs.