Emre Özer

Dr. Emre Özer

Industrial Engineering, Osmaniye Korkut Ata University, Osmaniye, Turkey (Türkiye)
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2022 in Materials Testing
Verified
Journal Article
Closed access
LGLevent Ulvi Gezici
Levent Ulvi Gezici
Emre ÖzerEmre Özer
Emre Özer
ISİbRahim Sarpkaya
İbRahim Sarpkaya
UÇUğur Çavdar
Uğur Çavdar
In this study, B4C and SiC hybrid reinforced Al–Cu–Mg–Si alloy Matrix composites were fabricated using a microwave sintering technique at a sintering temperature of 550 °C for 60 min. In the produced hybrid composites, while the B4C ratio was kept constant (3 wt%), SiC was used in four different amounts (3, 6, 9, and 12 wt%). In these produced hybrid composites, as a result of microwave sintering, thanks to the high microwave absorption of SiC, the porosities closed at a rate of 36.65–40.90%. In 3, 6, 9, and 12 wt% SiC reinforced composites, the microhardness of 100.1, 106.8, 114.4, and 117.2 HV0.05 were achieved, respectively. Due to agglomeration increasing with SiC reinforcement rate, delamination wears increased in 12 wt% SiC reinforced hybrid composite. As a result, the lowest specific wear rate was measured as 0.3374 × 10−3 mm3·(Nm)−1 in the 3 wt% B4C+9 wt% SiC reinforced sample.

6 June 2022 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
Emre ÖzerEmre Özer
Emre Özer
MAMehmet Ayvaz
Mehmet Ayvaz
MÜMustafa Übeyli
Mustafa Übeyli
ISİbrahim Sarpkaya
İbrahim Sarpkaya

1 October 2025 in Ceramics International
Verified
Journal Article
Closed access
Emre ÖzerEmre Özer
Emre Özer
DZDemet Zalaoglu
Demet Zalaoglu
MAMehmet Ayvaz
Mehmet Ayvaz
MÜMustafa Übeyli
Mustafa Übeyli
UAUmut Aksu
Umut Aksu
MEMusa Eryılmaz
Musa Eryılmaz

2 February 2025 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
Emre ÖzerEmre Özer
Emre Özer
MAMehmet Ayvaz
Mehmet Ayvaz
DZDemet Zalaoğlu
Demet Zalaoğlu
MÜMustafa Übeyli
Mustafa Übeyli
TÖTarık Özdoğru
Tarık Özdoğru

27 December 2023 in Materials Testing
Verified
Journal Article
Closed access
Emre ÖzerEmre Özer
Emre Özer
MAMehmet Ayvaz
Mehmet Ayvaz
This study aimed to produce hybrid composites with a AA2024 matrix reinforced by TiC/B4C/nano-graphite through a microwave-assisted sintering technique at 560 °C for 60 min. The nano-graphite ratio in the produced composite samples was kept constant as 1 wt.%. TiC and B4C were used in equal ratios at 2, 6 and 10 % by weight total to determine their effects on tribological properties. Wear tests were conducted under three different loads: 3, 5 and 10 N. In the hybrid composites produced, an inverse correlation was observed between the increase in reinforcement ratio and sinterability, while a direct correlation relationship was found in hardness and wear resistance. Compared to the sample containing 2 % TiC/B4C in total by weight, a ∼50 % increase in Brinell hardness and a 52–68 % decrease in wear rate was obtained in the sample containing 10 % TiC/B4C. As the reinforcement ratio increased, tribofilm formation increased, and abrasive wear was replaced by mild-oxidative wear type.

13 March 2024 in Arabian Journal for Science and Engineering
Verified
Journal Article
Open access
PDF file
Emre ÖzerEmre Özer
Emre Özer
MAMehmet Ayvaz
Mehmet Ayvaz
MÜMustafa Übeyli
Mustafa Übeyli
ISİbRahim Sarpkaya
İbRahim Sarpkaya
In the study, the effects of hybrid reinforcement (nano-alumina and MWCNT) and heat treatment on the wear behavior of the Al–4Cu nanocomposites were investigated under dry sliding condition against W–6Co ball by means of a ball-on-disk type tribometer. The load and the sliding speed were kept constant and selected to be 10 N and 0.1 m s−1, respectively, in the course of the wear tests. Meanwhile, the wear tests were completed after a total sliding distance of 1500 m was reached for each case. During these tests, the wear loss of the nanocomposites was measured at every 250 m. The worn surfaces of the nanocomposites were examined with the help of stereo and scanning electron microscopes. The volumetric wear rates, wear coefficients and wear mechanisms were identified for the nanocomposites to clarify the influence of reinforcement content and heat treatment on their wear resistance. The volume loss at the wear distance of 1500 m was obtained as 24.9 and 8.2 mm3 for the annealed and aged Al–4Cu alloy, respectively. On the other hand, it decreased to 4.6 and 3.2 mm3 in the case of the nanocomposites with 15% hybrid reinforcement in the annealed and aged conditions, successively. Moreover, increasing the hybrid reinforcement amount decreased the wear loss of the aged nanocomposites substantially in such a way that it resulted in the mild wear.