Frederico Ferlini

Dr. Frederico Ferlini

PPGEEL, Universidade Federal de Santa Catarina, Florianópolis, Santa Catarina, Brazil
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2007 in 26th IEEE VLSI Test Symposium (vts 2008)
Verified
Conference Paper
Closed access
AAAlexandre Amory
Alexandre Amory
FFFrederico Ferlini
Frederico Ferlini
MLMarcelo Lubaszewski
Marcelo Lubaszewski
FMFernando Moraes
Fernando Moraes
This paper presents new DfT modules required to use networks-on-chip as test access mechanism. The paper demonstrates that the proposed DfT modules can be also implemented on top of low cost networks-on-chip, i.e. networks without complex services. The DfT modules, which consist of test wrappers and test pin interfaces, are designed such that both the tester and CUTs transport test data unaware of the network. The DfT modules was analysed in terms of silicon area and test time, considering different network and test configurations.

6 February 2023 in Electronics
Verified
Journal Article
Open access
PDF file
FFFrederico Ferlini
Frederico Ferlini
FVFelipe Viel
Felipe Viel
Laio Oriel SemanLaio Oriel Seman
Laio Oriel Seman
HPHector Pettenghi
Hector Pettenghi
Eduardo BezerraEduardo Bezerra
Eduardo Bezerra
Valderi Reis Quietinho LeithardtValderi Reis Quietinho Leithardt
Valderi Reis Quietinho Leithardt
The increasing complexity of System-on-Chip (SoC) and the ongoing technology miniaturization on Integrated Circuit (IC) manufacturing processes makes modern SoCs more susceptible to Single-Event Effects (SEE) caused by radiation, even at sea level. To provide realistic estimates at a low cost, efficient analysis techniques capable of replicating SEEs are required. Among these methods, fault injection through emulation using Field-Programmable Gate Array (FPGA) enables campaigns to be run on a Circuit Under Test (CUT). This paper investigates the use of an FPGA architecture to speed up the execution of fault campaigns. As a result, a new methodology for mapping the CUT occupation on the FPGA is proposed, significantly reducing the total number of faults to be injected. In addition, a fault injection technique/flow is proposed to demonstrate the benefits of cutting-edge approaches. The presented technique emulates Single-Event Transient (SET) in all combinatorial elements of the CUT using the Internal Configuration Access Port (ICAP) of Xilinx FPGAs.

1 April 2012
Verified
Conference Paper
Closed access
FFFrederico Ferlini
Frederico Ferlini
FSFelipe A. da Silva
Felipe A. da Silva
Eduardo BezerraEduardo Bezerra
Eduardo Bezerra
DLDjones V. Lettnin
Djones V. Lettnin
The flexibility introduced by Commercial-Off-The-Shelf (COTS) SRAM based FPGAs in on-board system designs make them an attractive option for military and aerospace applications. However, the advances towards the nanometer technology come together with a higher vulnerability of integrated circuits to radiation perturbations. In mission critical applications it is important to improve the reliability of applications by using fault-tolerance techniques. In this work, a non-intrusive fault tolerance technique has been developed. The proposed technique targets soft processors (e.g. LEON3), and its detection mechanism uses a Bus Monitor to compare output data of a main soft-processor with its redundant module. In case of a mismatch, an error signal is activated, triggering the proposed fault tolerance strategy. This approach shows to be more efficient than the state-of-the-art Triple Modular Redundancy (TMR) and Software Implemented Hardware Fault Tolerance (SIHFT) approaches in order to detect and to correct faults on the fly with low area overhead and with no major performance penalties. The chosen case study is an under development On-Board Computer (OBC) system, conceived to be employed in future missions of the Brazilian Institute of Space Research (INPE).

29 April 2020 in Electronics
Verified
Journal Article
Open access
PDF file
FFFrederico Ferlini
Frederico Ferlini
Laio Oriel SemanLaio Oriel Seman
Laio Oriel Seman
Eduardo BezerraEduardo Bezerra
Eduardo Bezerra
Modern vehicles are integrating a growing number of electronics to provide a safer experience for the driver. Therefore, safety is a non-negotiable requirement that must be considered through the vehicle development process. The ISO 26262 standard provides guidance to ensure that such requirements are implemented. Fault injection is highly recommended for the functional verification of safety mechanisms or to evaluate their diagnostic coverage capability. An exhaustive analysis is not required, but evidence of best effort through the diagnostic coverage assessment needs to be provided when performing quantitative evaluation of hardware architectural metrics. These metrics support that the automotive safety integrity level—ranging from A (lowest) to D (strictest) levels—was obeyed. In this context, this paper proposed a verification solution in order to build an approach that can accelerate the diagnostic coverage assessment via fault injection in the semiconductor level (i.e., hardware description language). The proposed solution does not require any modification of the design model to enable acceleration. Small parts of the OpenRISC architecture (namely a carry adder, the Tick Timer peripheral, and the exception block) were used to illustrate the methodology.

1 December 2009
Verified
Conference Paper
Closed access
GGGuilherme Guindani
Guilherme Guindani
FFFrederico Ferlini
Frederico Ferlini
JOJeferson Oliveira
Jeferson Oliveira
NCNey Calazans
Ney Calazans
DPDaniel Pigatto
Daniel Pigatto
FMFernando Moraes
Fernando Moraes
Integrated circuits for very high-speed telecommunication protocols often use ASICs, due to their strict timing constraints. This scenario is changing, since modern FPGAs, implemented in 65 or 45 nm technologies achieve high operating frequencies, and serializer/deserializer hardwired modules enable the reception of high speed aggregated rates (e.g. 10 Gbps or more), spanning the input stream for internal parallel computation. This paper presents a complete solution for an optical transport network framer using FPGA devices. The framer receives a 10 Gbps stream originated from optical fiber medium, extracts its payload information, and transmits payload data at 10 Gbps. A working prototype was implemented in Virtex-4 and Virtex-5 devices.

1 March 2014
Verified
Conference Paper
Closed access
VMVictor M. Goncalves Martins
Victor M. Goncalves Martins
FFFrederico Ferlini
Frederico Ferlini
DLDjones Vinicius Lettnin
Djones Vinicius Lettnin
Eduardo BezerraEduardo Bezerra
Eduardo Bezerra
Field Programmable Gate Arrays (FPGAs), as any other electronic devices, are designed according to some life expectancy figures. For this reason, its lifetime is finite given due to appearance of faults caused by the natural physical degradation. In this paper, we present a low cost solution for autonomous detection of faults at the end of FPGAs life cycle. Our proposed methodology starts from a pre-analysis of memory elements belonging to modules under verification. Then, with a proper organization, it is created a list of all memory elements, controlled through a Built-In Self-Test (BIST) implementation via the FPGAs Internal Configuration Access Port (ICAP). By means of this list, a virtual scan chain is created, where the vectors (test and result) are written and read using the FPGA reconfiguration capabilities, which means there is no extra hardware to create the physical scan chain. The detection algorithm is implemented in the available system processing unit. The results show that with a minor increase in the program memory of the digital design, it is possible to perform an offline hardware testing of each sub-module in the existing FPGA, with no need of stopping the remaining of the system.