Fhatuwani Sengani

Dr. Fhatuwani Sengani

Department of Geology and mining, University of Limpopo

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 December 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
FSFhatuwani Sengani
Fhatuwani Sengani
FMFrançois Mulenga
François Mulenga
The purpose of this paper was to analyze the impact of extreme rainfall on the recurrence of slope instability using the Thulamela Municipality roads (R523) as a case study. To this end, the historical rainfall data of the area of study were analyzed between 1988 and 2018. The results show that a significant increase in rainfall is usually experienced in the summer months of December and January. Following this, the factor of safety (FoS) of slopes of silt clay, clay, and clay loam soils were estimated using the SLIDE simulator (Numerical software “Finite Element Method (FEM)”) under sunny to rainy conditions of the area. A complementary model, FLACSlope (Numerical software “Finite Difference Method (FDM)”), was utilized to simulate FoS and pore water pressure in sunny and rainy conditions of the area. Simulation results show that extreme rainfall has the ability to reduce the shear strength and resistance of the soil slope material. This may explain the recurrent landslides noted in the area. Finally, the water pore pressure has been simulated to increase with the increased water table, which generally pushes the soil particles apart and reduces the stress between the particles resulting in soil slope failure. Extreme rainfall alters the phase of the material solid in a manner that may require further research for a better understanding.

26 October 2020 in Sustainability
Verified
Journal Article
Open access
PDF file
FSFhatuwani Sengani
Fhatuwani Sengani
FMFrançois Mulenga
François Mulenga
The application of limit equilibrium analysis and numerical simulation in case of slope instability is described. The purpose of the study was to use both limit equilibrium methods (LEMs) and numerical simulations (finite element method (FEM)) to understanding the common factor imposing the selected slope into slope instabilities. Field observations, toppling analysis, rotational analysis, and numerical simulations were performed. The results of the study showed that the selected unstable slopes were associated with the sliding types of toppling; it was observed that the slopes were governed by tension cracks and layered soil mass and dominated with approximately two joints sets throughout. The simulated factor of safety (FoS) of the slopes composed of clay soil was denoted to be prone to slope instability while others were categorized as moderately stable. The simulated FoS of the slopes correlated very well with the visual observations; however, it is anticipated that properties of soil mass and other characteristics of the slopes contributed largely to the simulated FoS. The sensitivity of the model was further tested by looking into the effect of the slope angle on the stability of the slope. The results of the simulations showed that the steeper the slope, the more they become prone to instability. Lastly, Phase 2 numerical simulation (FEM) showed that volumetric strain, shear stress, shear strain, total displacement, and σ1 and σ3 components of the slope increase with the stages of the road construction. It was concluded improper road construction, steepness of the slope, slope properties (soil types), and multiple geological features cutting across are the common mechanisms behind the slope instability.

25 March 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
FSFhatuwani Sengani
Fhatuwani Sengani
DADhiren Allopi
Dhiren Allopi
Although limit equilibrium methods are widely used by engineers and scientists in predicting the stability of homogenous slopes, their use has been demonstrated to present significant errors due to the violation of kinematic and static admissibility. The concern is often voiced regarding the accuracy of limit equilibrium methods (LEMs) solutions in predicting the stability of homogenous slopes. There are no exact limit equilibrium solutions or charts available that could be used to check the LEMs solutions. The present study has used the rigorous upper and lower bounds solutions of limit analysis based on finite element formulations of the bound theorems to benchmark and develop an accuracy classification chart of limit equilibrium methods in predicting the stability of the homogenous slope. Six case studies of homogenous road-cut slopes that vary with material properties were used and the effect of the increase in material strength with depth was considered. The results of LEMs and limit analysis solutions have shown that Janbu simplified limit equilibrium solutions are closely related to those of rigorous upper bound solutions with an accuracy error ranging from 1 to 7% in various slope materials. Meanwhile, the Corp of Engineer 2 limit equilibrium solutions were found to overestimate among other methods, with an accuracy error ranging from 12 to 17% in various cases. Based on the results of the study an accuracy error classification chart of LEMs is developed.

4 September 2020 in International Journal of Geotechnical Engineering
Verified
Journal Article
Closed access
FSFhatuwani Sengani
Fhatuwani Sengani
FMFrançois Mulenga
François Mulenga
A review of the application of Particle Finite Element Methods (PFEM)to cases of rockfall and slope stability is described. The study commences with a summary of the basics of the PFEM, followed by the formulation for Lagrangian Continuum in PFEM, i.e., governing equation, local integration, contact discretization and mesh mapping. Case studies supporting the successful application of the method are also covered. The review revealed that PFEM is a powerful tool that is suitable for geotechnical problems. Nevertheless, it has been noted that the underlying model usually experienced so-called volumetric locking problems, which leads to numerical stiffening and spurious high spatial variability in the solution, resulting into numerical instability. It is believed that volumetric locking is due to the framework failure to satisfy the so-called Babuska-Brezzy conditions, the volumetric locking is also believed to be derived by so-called the equivalent inf-sup condition, as a results of improper finite dimensional space with the finite element discretization. Two methods,Fluid Pressure Laplacian technique (FPL) and Polynomial Pressure Projection (PPP), were adopted to solve the problem withthe latter noted to be the most suitable technique. The Polynomial Pressure Projection (PPP) has been successfully implemented in most cases while the Fluid Pressure Laplacian technique has not been successful reported to be implemented in most geotechnical problems. An overall conclusion of this study is that although there are several encouraging studies associated with the successfulness of PFEM in solving geotechnical problem, but it appears that serious inputs on developing and implementation advanced PFEM framework are required. This study suggested that advanced constitutive models or extending PFEM to deal with poromechanics-based hydromechanical coupling problem with large deformation can be the solution.

6 January 2024 in Scientific Reports
Verified
Journal Article
Open access
PDF file
NCNhleko Monique Chiloane
Nhleko Monique Chiloane
FSFhatuwani Sengani
Fhatuwani Sengani
FMFrancois Mulenga
Francois Mulenga
The behaviour of a stratified backfilled stope in terms of strength development and stress distribution has not been well established in the field of rock engineering. Yet, the mining industries with massive ore bodies are looking into high production with a high standard of safety which is mainly governed by large excavation with backfill as a support system. It is difficult to fill these large excavations at one time. Therefore, a subsequent backfilling of the stope layer by layering is adopted, which results in a layered backfill structure. The purpose of this study was to explore the strength development, stress distribution and deformation across the stope supported by both layered and non-layered backfill. It has been observed that the backfill support system gain its strength with time, however, the layered backfill support system loses its strength when more layers are introduced, this is due to the shearing effect around the interfaces of the backfill layers. The impact of layering was validated by 3D numerical simulation. It is therefore concluded that non layered backfill support system are more suitable for stoping mining methods rather than layered support system.

1 January 2018 in Journal of the Southern African Institute of Mining and Metallurgy
Verified
Journal Article
Open access
FSFhatuwani Sengani
Fhatuwani Sengani