This article describes research on FRCM (Fabric Reinforced Cementitious Matrix) composites, which unlike commonly used FRP (Fibre Reinforced Polymers) composites make use of a mineral matrix instead of epoxy resin, which allows to achieve much higher resistance to elevated temperatures. In the described studies, experimental measurement of deformations with the use of the DFOS (Distributed Fibre Optic Sensors) method was applied. This method allows for geometrically continuous measurement of deformations, which is its significant advantage compared to traditional electric resistance wire strain gauge, as it reduces the possibility of measuring deformations in a place where they are not representative. The tests were carried out using two reinforced concrete slab elements loaded to failure in the 4-point bending scheme. Fibre optic sensors were installed on an unstrengthened control element and on an element strengthened with FRCM composite. During the tests, deformations of the concrete under tension and the external surface of the FRCM reinforcing composite were determined. Measurements were carried out simultaneously in two manners: using the DFOS method, and strain gauges placed at the characteristic points of the element. The test results based on both methods were compared and analysed. The comparative analysis confirmed the usefulness and effectiveness of the DFOS method while measuring deformations in strengthening composites, and showed its significant advantages such as precise indication of the place of elements cracking as well as the possibility of conducting a global analysis of deformations.
From among the many technological solutions for floors in residential buildings and in small public buildings very often rib-and-block floor systems are selected. The main argument convincing project owners to choose such solutions are their clear advantages, mainly the uncomplicated construction technology, no need to use advanced tools and equipment and the low cost. The introduction of harmonized European guidelines in the form of the EN 15037 series of standards made it necessary to introduce changes in the designing and constructing of these commonly used floor systems, whereby their manufacturers had to update their offers. This paper discusses the requirements and the main changes introduced by the EN 15037 series of standards in comparison with the previous guidelines and general calculations of reinforced concrete structures according to Eurocodes. Analyses concerning bending and shear ultimate limit states and serviceability limit states are presented. Critical points in the design of rib-and-block floors are indicated and the results of exemplary calculations for a selected floor are presented. In addition, a comparative analysis concerning the difference in the consumption of reinforcing steel for a selected floor system designed according to respectively the current and previous guidelines is carried out and its results are discussed.
1 October 2019 in IOP Conference Series: Materials Science and Engineering
The use of FRCM (Fabric Reinforced Cementitious Matrix) composites for reinforced concrete elements structural strengthening is gaining increased popularity. This causes the need to better understand the work of the material and to propose an effective way of using it. The mechanical behaviour of FRCM composites related to their ductility and tendency to debond or delaminate causes that its typical use, known from the older FRP (Fibre Reinforced Polymers) technology, is inefficient, that was the reason for the anchoring concept. This paper presents the results of the research based on three slab type elements, two of which were strengthened with one layer of PBO-FRCM composite with GFRP rebar anchorage of the composite mesh ends. The most important mechanical properties of the elements were measured and analysed.
FRCM (Fabric-Reinforced Cementitious Matrix) composites, while providing an effective alternative to FRP (Fiber-Reinforced Polymer) strengthening systems when epoxy resins cannot be used, typically fail to achieve their full strengthening potential. Research indicates that appropriate mesh anchorage systems can minimize some of the undesirable effects that limit FRCM composite performance. This study investigates the effectiveness of different anchorage systems for PBO (p-Phenylene Benzobis Oxazole) fibers in FRCM composites used for strengthening reinforced concrete slabs. A series of unidirectionally bent RC slabs were tested under four-point bending: an unstrengthened control element, slabs strengthened with PBO-FRCM without anchorage, with bar anchorage (GFRP bar in a groove), and with cord anchorage (PBO cord through the slab). The research focused on analyzing the load–deflection behavior and key strain mechanisms that influence structural performance. The findings indicate that a single layer of PBO-FRCM increases bending capacity, raises yield load, and delays initial cracking. Most significantly, the research reveals substantial differences in composite mesh utilization efficiency. This study confirms that mechanical anchorage, particularly bar anchorage, significantly enhances the effectiveness of PBO-FRCM strengthening systems by delaying composite detachment and allowing for greater utilization of the high-strength fiber material. These results contribute valuable insights for RC slabs using FRCM composite systems and the anchorage of their mesh.
Wewnętrzne zbrojenie kompozytowe stanowiinnowacyjną alternatywę dla klasycznego zbrojenia stalowegow konstrukcjach betonowych. Charakteryzuje się ono korzystnymiwłaściwościami mechanicznymi, w szczególności wysokąodpornością na korozję, co czyni je szczególnie przydatnymw konstrukcjach narażonych na silną agresję chemiczną. Głównymograniczeniem zbrojenia kompozytowego jest jego kruchymechanizm zniszczenia, wymagający odmiennych metod projektowaniaw porównaniu do zbrojenia stalowego. Celem artykułujest analiza najważniejszych metod projektowania elementówżelbetowych ze zbrojeniem kompozytowym na zginanie. W pracyprzedstawiono wytyczne projektowe z norm amerykańskiej,kanadyjskiej, włoskiej i japońskiej, a następnie przeprowadzonoobliczeniową analizę porównawczą elementu zginanego. Wynikianalizy wykazały znaczące różnice w nośności obliczeniowej elementóworaz w przewidywanym mechanizmie zniszczenia
Celem pracy była eksperymentalna ocena wytrzymałościna ściskanie i zginanie kompozytu z rdzenia polistyrenowegowzmocnionego różną liczbą warstw włókien szklanychw żywicy epoksydowej. Badania prowadzone z wykorzystaniemmetody cyfrowej korelacji obrazu wykazały, że liczba zastosowanychwarstw laminatu i jego lokalizacja w znaczący sposóbwpływa na siłę niszczącą oraz mechanikę zniszczenia próbek ściskanychi zginanych. Zaproponowany kompozyt może być obiecującymmateriałem budowlanym.