Francisco Martínez-Zambrano

Prof. Francisco Martínez-Zambrano

Department of Mechanical Engineering, Universidad San Francisco de Quito, Quito, Pichincha, Ecuador
+1
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2021 in Journal of Cleaner Production
Verified
Journal Article
Open access
YKYusra Khalid
Yusra Khalid
May WuMay Wu
May Wu
ASArmin Silaen
Armin Silaen
Francisco Martínez-ZambranoFrancisco Martínez-Zambrano
Francisco Martínez-Zambrano
TOTyamo Okosun
Tyamo Okosun
DWDavid White
David White

21 November 2023 in Drones
Verified
Journal Article
Open access
PDF file
JAJonathan Arias
Jonathan Arias
Francisco Martínez-ZambranoFrancisco Martínez-Zambrano
Francisco Martínez-Zambrano
ECEDGAR HERNAN CANDO
EDGAR HERNAN CANDO
EVEsteban Valencia
Esteban Valencia
The implementation of distributed propulsion and boundary layer ingestion for unmanned aerial vehicles represents various challenges for the design of embedded ducts in blended wing body configurations. This work explores the conceptual design and evaluation of DP configurations with BLI. The aerodynamic integration of each configuration is evaluated following a proposed framework, including simulation analysis. Power saving coefficient and propulsive efficiency were compared against a baseline podded case. The results show the optimal propulsion configuration for the BWB UAV obtaining 3.95% of power benefit and propulsive efficiency (ηp>80%). Indeed, the aerodynamic integration effects for the proposed design maintain the BWB’s aerodynamic efficiency, which will contribute to longer endurance and better performance.

16 June 2021
Verified
Conference Paper
Closed access
PDF file
Francisco Martínez-ZambranoFrancisco Martínez-Zambrano
Francisco Martínez-Zambrano
ASArmin K. Silaen
Armin K. Silaen
KTKelly Tian
Kelly Tian
JMJoe Maiolo
Joe Maiolo
CZChenn Zhou
Chenn Zhou
Steelmaking is an energy-intensive process. Thus, energy efficiency is highly important. Several stages of steelmaking involve combustion processes. One of the most energy-consuming processes in steelmaking is the slab reheating process in a reheat furnace (RF). The energy released by fuel combustion is used to heat steel slabs to their proper hot-rolling temperature. The steel slabs move through the reheat furnace passing the three stages of heating called: Preheating Zone (PZ), Heating Zone (HZ), and Soaking Zone (SZ) to finally leave the discharge door at a rolling temperature of 2375 °F. One way to improve a reheat furnace’s fuel consumption is by implementing oxygen-enriched combustion. This study investigates the implementation of oxygen-enriched combustion in a pusher-type reheat furnace. The increment of oxygen in the combustion process allows for increasing the furnace gas temperature. Consequently, the oxygen enrichment approach allows for the reduction of fuel injection. The principal goal of this investigation is to model the combustion-based on oxygen-enrichment and develop parametric studies of fuel injection rates. The different simulations aim to match the slab heat flux profile of the industrial reheat furnace pusher-type. Computational fluid dynamics are used to generate the slab heat flux distribution. To reach more uniform slab heating, oxygen and fuel ports were alternated. Also, injection angles were modified to optimize slab heating and avoid the impact of hot spots. Thermocouple readings of the industrial reheat furnace are compared to simulation results. The results determined that 40–45% fuel reduction can be achieved.

13 July 2020
Verified
Conference Paper
Closed access
Francisco Martínez-ZambranoFrancisco Martínez-Zambrano
Francisco Martínez-Zambrano
BWBethany Worl
Bethany Worl
XLXiang Li
Xiang Li
ASArmin K. Silaen
Armin K. Silaen
NWNicholas Walla
Nicholas Walla
CZChenn Zhou
Chenn Zhou
During the steelmaking and hot rolling processes, various defects and cracks appear throughout the steel product. These cracks may initiate and grow throughout the hot rolling process and result in a lower quality of the product than is acceptable. The most energy-intensive part of the hot rolling process is the reheating furnace, where slabs are heated up to a target rolling temperature largely through radiant heat transfer. In the reheat furnace, large stresses may develop due to the thermal gradients within the steel product. A thermal-stress analysis is proposed based on finite element method (FEM) to study the impacts of charging temperature, slab velocity, and heating rate on stress development as the steel slab travels through an industrial pusher-type reheat furnace. Furnace zone information is taken from a previously validated computational fluid dynamics (CFD) model and applied as thermal boundaries and constraints within the thermal-stress FEM models. Temperature and stress results were taken at the core, top, bottom, top quarter, and the bottom quarter of the steel slab at different residence times. Moreover, temperature lines and contour plots taken along the length of the slab allow visualization of the gradual development of temperature and identification of the locations corresponding to temperature variations as the slabs move in the furnace. The slab temperature predicted by the FEM model was found valid when compared with industrial data. Stress predictions found similar trends with previously published works as well as evidence of thermal shock in the sub-surface near the beginning of the residence time.

1 January 2021
Verified
Conference Paper
Closed access
LFL. Fabina
L. Fabina
KJK. Johnson
K. Johnson
JMJ. Maiolo
J. Maiolo
Francisco Martínez-ZambranoFrancisco Martínez-Zambrano
Francisco Martínez-Zambrano
ASA. Silaen
A. Silaen
CZC. Zhou
C. Zhou
An important part of the hot rolling process is the reheating of steel products to target temperature using combustion of natural gas in a furnace. To increase energy efficiency of this reheating process, oxygen enrichment can be used with high entrainment of reaction product gases to distribute the combustion reaction area. The modeling of various configurations was undertaken using computational fluid dynamics to use oxygen enrichment or oxy-fuel in order to avoid changes in the furnace zone temperatures while reducing fuel usage. Effects on the combustion, temperature distribution, species and heat transfer to the steel product are under study.

1 November 2021
Verified
Conference Paper
Closed access
PDF file
BWBethany Worl
Bethany Worl
Francisco Martínez-ZambranoFrancisco Martínez-Zambrano
Francisco Martínez-Zambrano
XLXiang Li
Xiang Li
ASArmin K. Silaen
Armin K. Silaen
KJKurt Johnson
Kurt Johnson
CZChenn Zhou
Chenn Zhou
The most energy intensive part of a hot rolling mill is the reheat furnace, where the steel products, the products are heated to target temperature using the combustion of natural gas. The energy consumption of the reheat furnace in a typical integrated steel mill is the second highest after blast furnace. Any improvement to energy efficiency of the reheat furnace can have significant impact on the overall energy efficiency of the steel plant. Oxygen enrichment of the combustion air beyond 21 vol% oxygen can be used to improve the furnace energy efficiency. The molar fraction of oxygen is increased, replacing nitrogen in the combustion air. In this study, computational fluid dynamics modeling of various burner configurations was conducted to investigate the application of oxygen enrichment or oxy-fuel to reduce fuel usage while maintain a given slab heating rate. The applications of medium oxygen enrichment (46 vol% O2) and oxy-fuel (100 vol% O2) in the preheating zone, which has the highest fuel usage of the three furnace zones, were investigated.