Gangwei Zhu

Dr. Gangwei Zhu

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 December 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Gangwei ZhuGangwei Zhu
Gangwei Zhu
JDJianning Dong
Jianning Dong
WSWenli Shi
Wenli Shi
TSThiago Batista Soeiro
Thiago Batista Soeiro
JXJunzhong Xu
Junzhong Xu
Pavol BauerPavol Bauer
Pavol Bauer
This article proposes a mode-switching-based phase shift control (MS-PSC) for wireless power transfer (WPT) systems, which is able to achieve power regulation, load matching, and wide ZVS operations simultaneously without using additional dc–dc converters. Based on the mode transitions between the full-bridge, mixed-bridge, and half-bridge modes of both the inverter and the rectifier, the MS-PSC method guarantees a wide-range ZVS with minimized circulation of reactive power. Therefore, the system efficiency is improved over a wider power range compared to the conventional triple-phase-shift (TPS) control and the existing hybrid modulation control. The principles of different operating modes are analyzed. Then, the implementation of the proposed MS-PSC method and the mode selection strategy are presented. Finally, the effectiveness of the proposed MS-PSC method is validated in a WPT prototype. Experimental results show that the proposed MS-PSC method can achieve a high overall efficiency in a wide power range. Compared with the conventional TPS control, the MS-PSC method further optimizes the efficiency in 10%–63% of the rated power, with efficiency improvements ranging from 1.5% to 6%. As a result, the system efficiency remains at 93.5%–96.1% in the power range of 1–10 kW, with the transformer coupling coefficient k = 0.19.

16 December 2024 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
Gangwei ZhuGangwei Zhu
Gangwei Zhu
JDJianning Dong
Jianning Dong
FGFrancesca Grazian
Francesca Grazian
Pavol BauerPavol Bauer
Pavol Bauer
This paper presents a hybrid modulation (HM) scheme to facilitate secondary-side control in wireless power transfer (WPT) systems. To achieve broad power regulation in WPT systems, the conventional pulse width modulation (PWM) exhibits a significant efficiency drop under light loads, while the existing pulse density modulations (PDMs) lead to considerable current and voltage ripples. To address this issue, an optimal discrete PDM (D-PDM) is proposed for active rectifier modulation. By symmetrically and uniformly distributing pulses, the proposed optimal D-PDM eliminates even-subharmonics in rectifier input voltage, thereby reducing the current distortions and output voltage ripple while removing the capacitor DC blocking voltages. Moreover, the pulse width regulation is incorporated into the optimal D-PDM, enabling continuous output tuning and further minimizing subharmonics in the voltage. Based on a WPT prototype, the proposed HM is benchmarked with the existing PWM and PDMs. Experimental results show that the proposed HM significantly mitigates current and voltage ripples while facilitating continuous tuning when compared with the existing PDMs. Additionally, when compared to the PWM, the proposed HM demonstrates notable efficiency improvements within the 10%-60% power range, achieving a maximum efficiency enhancement of up to 5.5%.

11 March 2025 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Gangwei ZhuGangwei Zhu
Gangwei Zhu
SZShibo Zhang
Shibo Zhang
ZDZichen Deng
Zichen Deng
JWJundong Wang
Jundong Wang
YLYongpeng Li
Yongpeng Li
Pavol BauerPavol Bauer
Pavol Bauer
This article presents an extended hybrid modulation (EHM) technique to achieve multistage constant-current (MSCC) charging of electric vehicles using wireless power transfer (WPT) technology. Although most research focuses on constant-current constant-voltage charging, MSCC charging offers key advantages, such as lower temperature rise, decreased charging time, and prolonged battery lifespan. However, the existing phase-shift-modulation (PSM) method encounters substantial circulating reactive power and significant efficiency drops in MSCC charging. To overcome this, an EHM strategy is proposed to expand the modulation range of PSM. By applying EHM to both the inverter and active rectifier, the proposed method provides up to 16 operating modes to facilitate multiple CC outputs. Furthermore, an optimal mode trajectory, specifically designed for the MSCC charging, is developed. By implementing this trajectory across different charging stages, zero-voltage-switching is achieved for all power switches, and the overall power loss of the system is minimized. Finally, a WPT prototype was developed to validate the proposed approach. Experimental results demonstrate that the proposed approach effectively enables the MSCC charging while notably enhancing transmission efficiency, achieving dc-to-dc efficiencies between 92.45% and 95.67% across a power range of 231 to 3.015 kW.

4 August 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
Gangwei ZhuGangwei Zhu
Gangwei Zhu
JDJianning Dong
Jianning Dong
FGFrancesca Grazian
Francesca Grazian
Pavol BauerPavol Bauer
Pavol Bauer
This paper presents a parameter recognition based impedance tuning method for the impedance mismatch caused by capacitance drift and coil misalignment in series-series (SS)-compensated wireless power transfer (WPT) systems. First, a parameter recognition method is proposed to identify the unknown parameters of the resonant circuits by only measuring the RMS values of the coil currents. No phase detection circuits and auxiliary measurement coils are required. Furthermore, according to the recognized parameters, the reactance on both sides are minimized simultaneously by regulating the system frequency and the phase shift angles of the active rectifier. Compared with the existing methods, the proposed parameter recognition method adopts a dynamic frequency approaching strategy to avoid severe system detuning due to the bifurcation phenomenon. Moreover, based on the recognized parameters, the proposed impedance tuning method can simultaneously cope with the parameter deviations caused by capacitance drift and coil misalignment on both sides without using extra circuits and switches. Experimental results show that the unknown parameters of the resonant circuits are recognized accurately, with the average relative errors all less than 3%. Additionally, by implementing the impedance tuning method, the dc to dc efficiency of the WPT prototype is improved by 4.3%-15% in the experiments.

26 December 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
GYGuangyao Yu
Guangyao Yu
JDJianning Dong
Jianning Dong
TSThiago Batista Soeiro
Thiago Batista Soeiro
Gangwei ZhuGangwei Zhu
Gangwei Zhu
YYYu Yao
Yu Yao
Pavol BauerPavol Bauer
Pavol Bauer
This article introduces a three-mode variable-frequency zero-voltage switching (ZVS) modulation method for the four-switch buck+boost converter. This method makes this circuit concept well suited for applications, such as wireless power charging of electric vehicles, where this circuit operates as a power buffer between the resonant converter and the battery with the function to implement the required charging profile. Herein, the buck+boost converter operation is subdivided into three operating regions according to the converter static voltage gain, i.e., buck-, buck-boost- and boost-type modes. A ZVS turn- on triangular current mode (TCM) control is adopted for buck-type and boost-type modes. In the buck-boost-type mode when the input-to-output voltage gain is close to unit, all the possible modulation cases are studied thoroughly based on the phase shift of the two half bridges in a full switching period. The selection of the most suitable modulation scheme is performed to minimize the rms value of the inductor current while taking into account the simplification of the practical implementation. Closed-form equations are derived, which makes it easy to implement in practice. The proposed strategy is described, analyzed, and finally verified through a 3 kW surface mounted device (SMD) silicon carbide (SiC) mosfet -based laboratory prototype with designed input voltage of 300–600 V and the typical output voltage of 400 V class battery. The efficiency from the measured results is remarkably high, i.e., between 99.2% and 99.6% in a power range from 1 to 3 kW. Finally, tests for the operating mode transitions demonstrated the feasibility of the proposed modulation method. The power density of this converter is 4.86 kW/L.

13 June 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Gangwei ZhuGangwei Zhu
Gangwei Zhu
JDJianning Dong
Jianning Dong
GYGuangyao Yu
Guangyao Yu
WSWenli Shi
Wenli Shi
CRCalvin Riekerk
Calvin Riekerk
Pavol BauerPavol Bauer
Pavol Bauer
This article presents an optimal multivariable control (OMC) strategy for the LCC–LCC compensated wireless power transfer systems. To mitigate reactive power and achieve higher efficiency, the proposed OMC method incorporates dual-side hybrid modulation and primary-side switch-controlled-capacitor (SCC) tuning into the triple-phase-shift (TPS) control. First, the impact of hybrid modulation and SCC tuning on the system characteristics is investigated. The inverter and rectifier zero-voltage-switching (ZVS) conditions are then analyzed to achieve dual-side ZVS with minimal reactive power. Furthermore, a multivariable optimization problem is established based on the power loss analysis. The solution to this problem provides optimal control variables that minimize the overall system loss. Through collaborative modulation and control of the inverter, rectifier, and SCC, the proposed method reduces the rms values of the currents and lowers the turn- off currents for the converters. As a result, this approach improves efficiency in both light- and heavy-load conditions, enabling wide output regulation and full-range efficiency optimization simultaneously. Finally, the proposed method is benchmarked with the existing TPS method. Experimental results demonstrate that the proposed method achieves higher dc-to-dc efficiency in the power range of 0.2–2.2 kW, with a maximum efficiency improvement of up to 6.3%.