Sonochemical production of tin(II) and tin(IV) sulfides is investigated. Different conditions of syntheses are examined: used solvent (ethanol or ethylenediamine), source of tin (SnCl2 or SnCl4), the molar ratio of thioacetamide to the tin source, and time of sonication. The obtained powders are characterized by the X-ray diffraction method (PXRD), scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDX), and the Tauc method. Raman and FT-IR measurements were performed for the obtained samples, which additionally confirmed the crystallinity and phase composition of the samples. The influence of experimental conditions on composition (is it SnS or SnS2), morphology, and on the bandgap of obtained products is elucidated. It was found that longer sonication times favor more crystalline product. Each of bandgaps is direct and most of them show typical values - c.a. 1.3 eV for SnS and 2.4 eV for SnS2. However, there are some exceptions. Synthesized powders show a variety of forms such as needles, flower-like, rods, random agglomerates (SnS2) and balls (SnS). Using ethanol as a solvent led to powders of SnS2 independently of which tin chloride is used. Sonochemistry in ethylenediamine is more diverse: this solvent protects Sn2+ cations from oxidation so mostly SnS is obtained, while SnCl4 does not produce powder of SnS2 but Sn(SO4)2 instead or, at a higher ratio of thioacetamide to SnCl4, green clear mixture.
Sonochemical synthesis is becoming a popular method of preparing various nanomaterials, including metals, carbons, oxides, and chalcogenides. This method is relatively cheap and responds to the challenges of green chemistry as it typically does not involve high temperatures, high pressures, inert atmospheres, or long reaction times in comparison to other conventional methods. The utilization of ultrasound in synthesis makes the elimination of toxic solvents possible, as well as the execution of the synthesis without the use of reducing and stabilizing agents, while receiving products with the same or even better properties. The application of ultrasound allows for the synthesis of various nanomaterials with different properties for use in fields such as catalysis, electrochemistry, medicine, and biosensors. The final product is influenced by multiple variables such as temperature, pH, reagents, capping agents, time of reaction, and the addition of dopants.
Our study reports the ultrasound-assisted synthesis of SnS and SnS2 in the form of nanoparticles using aqueous solutions of respective tin chloride and thioacetamide varying sonication time. The presence of both compounds is confirmed by powder X-ray diffraction, energy-dispersive X-ray spectroscopy, as well as Raman and FT-IR spectroscopic techniques. The existence of nanoparticles is proven by powder X-ray diffraction investigation and by high resolution transmission electron microscopy observations. The size of nanocrystallites are in the range of 3-8 nm and 30 50 nm for SnS, and 1.5-10 nm for SnS2. X-ray photoelectron spectroscopy measurements, used to investigate the chemical state of tin and sulphur atoms on the surface of nanoparticles, reveal that they are typically covered with tin on the same oxidation degree as respective bulk compound. Values of optical bandgaps of synthesized nanoparticles, according to the Tauc method, were 2.31, 1.47 and 1.05 eV for SnS (60, 90 and 120 min long synthesis, respectively), and 2.81, 2.78 and 2.70 eV for SnS2 (60, 90 and 120 min long synthesis, respectively). Obtained nanoparticles were utilized as photo- and sonocatalysts in the process of degradation of model azo-dye molecules by UV-C light or ultrasound. Quantum dots of SnS2 obtained under sonication lasting 120 min were the best photocatalyst (66.9 % color removal), while quantum dots of SnS obtained under similar sonication time were the best sonocatalyst (85.2 % color removal).
SnS and SnS2 powders were synthesized with the use of ultrasound. The indirect sonication was applied with ultrasound frequency 40 kHz and acoustic power 38 W/L. Products of syntheses were examined with PXRD, TEM, EDX, XPS, and UV-Vis (the Tauc method) investigations. The resulting microparticles were used for tip coating of copper cathodes. These electrodes were used in the degradation of model azo-dye Metanil Yellow by the electro-Fenton process. The efficiencies of degradation using copper, SnS-coated copper, and SnS2-coated copper cathodes are compared. Kinetics of degradation of Metanil Yellow in the electro-Fenton process with the application of three different cathodes is also investigated. It was found that the degradation follows pseudo-first-order and that SnS-coated copper cathode improves the efficiency of degradation, while SnS2-coated copper cathode decreases the efficiency of degradation.
Nanomaterials, including quantum dots, have gained more and more attention in the past few decades due to their extraordinary properties that make them useful for many applications, ranging from catalysis, energy generation and storage, biotechnology, and medicine to quantum informatics. Mathematical descriptions of the phenomena in which nanostructures are involved are of great demand because they may be utilized for the purpose of controlling these phenomena (e.g., the growth of nanostructures with certain sizes, shapes, and other properties). Such models may be of distinct nature, including calculations from first principles, ordinary and partial differential equations, and machine learning models (including artificial intelligence) as well. The aim of this article is to review the most important and useful computational and mathematical approaches for the description and control of processes involving nanostructures.