This report presents the results of the development of method of forming of motion laws for mechatronics objects (MO) along trajectories with the desired speed. Desired trajectories are described by third order parametric splines. Analytical expressions describing the dependence of the rate of change of the parameter from the laws of change of given speed and information about the parametric form of a trajectories are obtained. They allow to move the program point along the trajectory accurately at a given speed. The described approach does not require iterative calculations and allows to perform all necessary calculations in real-time even on low-power onboard robots' computers.
This paper presents a new advanced approach for automatization of processing of flexible parts with arbitrary geometrical forms. This approach based on using multilink manipulators with vision system and allows to exclude the individual equipment for rigid fixing of processed parts. This is achieved by formation and correction of program motions of cutting tool of manipulator using information about current position of processed parts from 3D vision system
This paper proposes a method for the identification of kinematic parameters of multilink series industrial robots, which does not require the use of complex and expensive equipment for high-precision external measurements of the position and orientation of an end effector in a Cartesian coordinate system. This method, by means of simple and affordable tools, enables us to achieve a significantly increased accuracy of movement of end effectors in serial robots performing various technological operations. The proposed method is experimentally verified and can be applied directly in production lines.
In this work the combination method of three-dimensional models of processed details with their reference CAD-models when these details have unknown in advance deformation is proposed. This method assumes preliminary transformation of models to clouds of points, special density increasing of these clouds and their iterative combination by means of ICP (Iterative Closest Points) algorithm. Model example demonstrates the efficiency and effectiveness of proposed approach.
7 December 2020 in Mekhatronika, Avtomatizatsiya, Upravlenie
Рассмотрено решение задачи повышения производительности робототехнических систем, в состав которых входят многостепенные манипуляторы, а их исполнительные элементы имеют ограничения по мощности. Для решения этой задачи разработан метод автоматического формирования предельно высоких программных скоростей движения рабочих инструментов указанных манипуляторов, позволяющий сохранить заданную динамическую точность управления с учетом взаимовлияний между всеми их степенями подвижности и заданных ограничений на входные сигналы электроприводов. Созданный метод заключается в вычислении максимально допустимой скорости движения рабочего инструмента манипулятора. Основной особенностью метода являются условия выбора требуемых данных для быстрого расчета всех необходимых параметров управления. На основе предложенного метода синтезирована система формирования скорости движения рабочего инструмента трехзвенного манипулятора с поворотными степенями подвижности, приводимыми в движение двигателями постоянного тока. Этот манипулятор может перемещать рабочие инструменты по произвольным гладким пространственным траекториям, построенным с помощью параметрических сплайнов третьего порядка. Выполненное моделирование подтвердило высокую эффективность предложенного метода в сравнении с другими известными методами задания программной скорости и позволило существенно повысить программную скорость движения рабочих инструментов за счет непрерывной работы хотя бы одного из электроприводов манипулятора вблизи зоны насыщения его усилителя мощности без входа в нее. При этом повышение быстродействия системы происходило без уменьшения динамической точности. Разработанный метод может быть применен для формирования предельно высокой программной скорости движения рабочих инструментов манипуляторов с любыми кинематическими схемами и различным числом степеней подвижности.