In this article, the growth of aerodynamic efficiency and the growth of the wing structural stress is studied for DLR-F4 typical transport aircraft wing-body, after installing classical Whitcomb winglets of different configurations and a delta wingtip fence. A new-concept curved-span winglet was mathematically developed and approved through Computational Fluid Dynamics (CFD) and static structural experiments, revealing the interaction of sub- and transonic air flow dynamics with the wingtip device geometry. The design space of the winglet geometry was explored briefly, and an evaluation of the lift-to-drag ratio increment depending on various winglet input parameters was performed. In particular, the winglet cant angle effect on lift and drag was thoroughly analyzed at various flow regimes and angles of attack, revealing an ambiguity and a conflicting character of results between highly canted winglets and nearly vertical ones. As a result of cant angle impact analysis, a curved winglet concept is suggested and mathematically parametrized, that could provide an innovative solution, alternative to a morphing winglet, but much simpler with a fixed structure. In conclusion, a multidisciplinary winglet efficiency estimation criterion is suggested for comparing the aerodynamic efficiency of different wingtip devices with respect to their structural weight penalty in real flight conditions.
This study aimed to explore the directional stability issues of a previously studied light box-wing aircraft model with a pusher propeller engine in the fuselage aft section. Earlier configurations have included the use of fuselage together with a lifting system consisting of two wings joined together at their wingtips with vertical stabilizers. However, these side vertical surfaces failed to provide the aircraft with sufficient directional stability, thus prompting the quest in this study for novel solutions that would exclude the need for a fuselage extension and a typical fin. Solutions included the use of a ducted propeller and few configurations of small “fishtail” vertical fins, which formed part of the aft fuselage itself and coupled with vortex generators on the fuselage surface to improve their interference and heal flow separation at the fuselage aft cone. The results of wind tunnel testing were supported with CFD simulations to explain the flow behavior of each of the studied solutions. Tuft visualization and computed flow patterns allowed identification of the sources of the observed low efficiency in terms of directional stability of the fishtail against a simple idle duct without a propeller. A final configuration with a duct and a modified version of the fuselage fins was achieved that provides enough yaw stability margins for a safe flight.
This paper addresses the inverse aeroelastic design problem for a transport-aircraft wing: given a target cruise flying shape, determine the spanwise bending-stiffness distribution - and hence the structural sizing - that produces this shape under the corresponding aerodynamic load. The NASA Common Research Model (CRM) wing at Mach 0.85 is used as the reference configuration. A closed-form analytical method based on Euler–Bernoulli beam theory with a geometrically nonlinear curvature expression is used to back-calculate the required bending stiffness EI(z) from a target elliptical deflection profile and a bending-moment distribution. The aerodynamic load is obtained from a Reynolds-Averaged Navier–Stokes CFD solution (ANSYS Fluent, k-ω SST) verified against Sixth AIAA CFD Drag Prediction Workshop (DPW-6) wind-tunnel data, showing agreement within 7% in lift and 5% in drag over 0-4° angle of attack. A parametric shell finite-element model of the wing box (twin-spar, variable-pitch ribs) is built in ANSYS Mechanical, in which bending stiffness is controlled solely through skin thickness, without re-building the geometry. Required skin-thickness distributions, inverse-computed from the CFD load, are applied to this model, and a one-way fluid–structure interaction analysis is performed by mapping the rigid-wing surface pressure onto the structural mesh. The resulting deflection matches the target profile closely for η<0.75; the larger deviation near the tip is attributable to a minimum manufacturing gauge constraint on skin thickness (2 mm) rather than to a methodological shortcoming. The approach offers a computationally inexpensive engineering alternative to full multidisciplinary design optimization for preliminary aeroelastic wing sizing.
This study investigates the effect of downward deflection of a bio-inspired corrugated airfoil on steady-state and dynamic properties for micro air vehicles (MAVs). An efficient data-driven optimization framework proposes to optimize the airfoil. Based on the surrogate model optimization workflow, this framework deeply integrates computational fluid dynamics simulations, neural network surrogate models, and the particle swarm optimization algorithm to systematically optimize the downward deflection angles of the airfoil's multiple troughs, successfully obtaining an optimal geometric configuration. By numerical simulations based on the static and dynamic motion trajectories of the MAV, the optimized airfoil shows superior performance than baseline airfoil. Static aerodynamic analysis indicates that the optimized airfoil achieves an 8%–135% improvement in the lift-to-drag ratio across a 0°–36° angle-of-attack range, and delays the critical stall angle from 12° to 17°. Flow mechanism analysis reveals that the performance leap stems from a more favorable pressure distribution and a more stable boundary layer, which effectively suppresses large-scale flow separation. Dynamic flapping simulation shows that optimized airfoil achieved a 6.5% increase in average lift and a 9.2% increase in average thrust than baseline airfoil over a complete cycle. These demonstrates the importance of downward deflection to the aerodynamic performance improvement of corrugated airfoils and engineering value of the proposed optimization framework in addressing multi-parameter airfoil design for MAVs.