Guglielmo Vivarelli

Dr. Guglielmo Vivarelli

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 May 2025 in Fluids
Verified
Journal Article
Open access
PDF file
GVGuglielmo Vivarelli
Guglielmo Vivarelli
Ning QinNing Qin
Ning Qin
SSShahrokh Shahpar
Shahrokh Shahpar
Mesh adaptation techniques can significantly impact Computational Fluid Dynamics by improving solution accuracy and reducing computational costs. In this review, we begin by defining the concept of mesh adaptation, its core components and the terminology commonly used in the community. We then categorise and evaluate the main adaptation strategies, focusing both on error estimation and mesh modification techniques. In particular, we analyse the two most prominent families of error estimation: feature-based techniques, which target regions of high physical gradients and goal-oriented adjoint methods, which aim to reduce the error in a specific integral quantity of interest. Feature-based methods are advantageous due to their reduced computational cost: they do not require adjoint solvers, and they have a natural ability to introduce anisotropy. A substantial portion of the literature relies on second-order derivatives of scalar flow quantities to construct sensors that can be equidistributed to minimise discretisation error. However, when used carelessly, these methods can lead to over-refinement, and they are generally outperformed by adjoint-based techniques when improving specific target quantities. Goal-oriented methods typically achieve higher accuracy in fewer adaptation steps with coarser meshes. It will be seen that various approaches have been developed to incorporate anisotropy into adjoint-based adaptation, including hybrid error sensors that combine feature-based and goal-oriented indicators, sequential strategies and adjoint weighting of fluxes. After years of limited progress, recent work has demonstrated promising results, including certifiable solutions and applications to increasingly complex cases such as transonic compressor blades and film-cooled turbines. Despite these advances, several critical challenges remain: efficient parallelisation, robust geometry integration, application to unsteady flows and deployment in high-order discretisation frameworks. Finally, examples of the potential role of artificial intelligence in guiding or accelerating mesh adaptation are also discussed.

1 May 2021 in Computers & Fluids
Verified
Journal Article
Closed access
GVGuglielmo Vivarelli
Guglielmo Vivarelli
NQNing Qin
Ning Qin
SSShahrokh Shahpar
Shahrokh Shahpar
DRDavid Radford
David Radford

JIJoão Isler
João Isler
GVGuglielmo Vivarelli
Guglielmo Vivarelli
CCChris Cantwell
Chris Cantwell
Francesco MontomoliFrancesco Montomoli
Francesco Montomoli
SSSpencer Sherwin
Spencer Sherwin
RVRAUL VAZQUEZ
RAUL VAZQUEZ
Direct numerical simulations (DNSs) of the T106A low-pressure turbine were conducted for various turbulence intensities and length scales to investigate their effects on flow behaviour and transition. A source-term formulation of the synthetic eddy method (SEM) was implemented in the Nektar++ spectral/hp element framework to introduce anisotropic turbulence into the flow field. A single sponge layer was imposed, which covers the inflow and outflow regions just downstream and upstream of the inflow and outflow boundaries, respectively, to avoid acoustic wave reflections on the boundary conditions. Additionally, in the T106A model, mixed polynomial orders were utilized, as Nektar++ allows different polynomial orders for adjacent elements. A lower polynomial order was employed in the outflow region to further assist the sponge layer by coarsening the mesh and diffusing the turbulence near the outflow boundary. Thus, this study contributes to the development of a more robust and efficient model for high-fidelity simulations of turbine blades by enhancing stability and producing a more accurate flow field. The main findings are compared with experimental and DNS data, showing good agreement and providing new insights into the influence of turbulence length scales on flow separation, transition, wake behaviour, and loss profiles.

1 January 2023
Verified
Conference Paper
Open access
PDF file
GVGuglielmo Vivarelli
Guglielmo Vivarelli
JIJoao Anderson Isler
Joao Anderson Isler
FMFrancesco Montomoli
Francesco Montomoli
SSSpencer Sherwin
Spencer Sherwin
PAPaolo Adami
Paolo Adami
RVRaul Vazquez-Diaz
Raul Vazquez-Diaz
During the early phases of the turbomachinery design process, it is often the case that various simplifications and assumptions can be made when attempting to understand the boundary layer behaviour subject to pressure gradients. For example, simplified boundary-layer models, which neglect the effect of surface curvature and/or density variations, while retaining the non-dimensional pressure distribution over the suction surface, can be employed to appreciate losses incurred to understand the flow behaviour over gas turbine components. The objective of this paper is understand and quantify the implication of those simplifications on this type of flow. The effect of the compressibility on a boundary layer over a flat plate under representative pressure gradient was investigated and presented in a separate paper. To gain further insight into the effect of this simplification, here we extend our previous work to a more representative case. A set of 2D fan profiles, representing the pressure distribution found at 70% and 90% span of a modern Low Speed fan for a UHBP turbofan, are analysed at cruise conditions. In order to investigate the effects of compressibility the two profiles were redesigned to achieve exactly the same non-dimensional pressure distribution over the suction side at incompressible conditions. The resulting boundary layer quantities will be compared explaining the necessary scaling required along with the reasons behind the discrepancies, such as the effect of density variations. To investigate the curvature ramifications, the results from these fan profiles will be compared with those of a flat plate with the same non-dimensional pressure gradient subject to the same high-Reynolds number incoming flow. The second test-case considered is a flat plate with a strong adverse pressure gradient subject to a high-Reynolds number incoming flow. This particular geometry is the same for both compressible and incompressible computations as the peak Mach number is just shy of the 0.3 threshold in a restricted region outside the boundary layer. In this case, the flow behaviour is much more complex: to start with, the adverse pressure gradient causes a separation bubble to appear. Viscous instabilities in the form of Tollmien–Schlichting waves materialise along the free-flow/bubble interface; these are then followed by Kelvin-Helmholtz inviscid instabilities in the form of 2D cylindrical structures. The latter interact with the secondary vortical instabilities ejected from the bubble. Consequently, turbulent transition develops downstream. For this particular geometry, the comparison will detail the reasons behind the separation point and any turbulent transition differences. Similarities in terms of the overall behaviour will be highlighted, thus allowing us to determine whether the incompressible boundary layer assumption may be valid and what sort of inaccuracies are being introduced. All test-cases will be analysed by means of the spectral/hp-element flow solver Nektar++. This is a high-order finite-element method type code having both compressible and incompressible formulations. Employing this kind of software will allow to reach Direct Numerical Simulation range for all the simulations carried out in this work, that would otherwise be unobtainable with lower-order discretisations typically found in industry.

19 June 2020 in International Journal for Numerical Methods in Fluids
Verified
Journal Article
Open access
PDF file
GVGuglielmo Vivarelli
Guglielmo Vivarelli
NQNing Qin
Ning Qin
SSShahrokh Shahpar
Shahrokh Shahpar
DRDavid Radford
David Radford
Summary: Nowadays, aerodynamic computational modeling is carried out on a daily basis in an industrial setting. This is done with the aim of predicting the performance and flow characteristics of new components. However, limited resources in terms of time and hardware force the engineer to employ relatively coarse computational grids, thus achieving results with variable degree of inaccuracy. In this article, a novel combination of feature and adjoint‐based mesh adaptation methods is investigated and applied to typical three‐dimensional turbomachinery cases, such as compressor and fan blades. The proposed process starts by employing feature‐based mesh movement to improve the global flow solution and then adjoint refinement to tune the mesh for each quantity of interest. Comparison of this process with one utilizing only the adjoint refinement procedure shows significant benefits in terms of accuracy of the performance quantity.

GVGuglielmo Vivarelli
Guglielmo Vivarelli
JIJoão Isler
João Isler
CCChris Cantwell
Chris Cantwell
Francesco MontomoliFrancesco Montomoli
Francesco Montomoli
SSSpencer Sherwin
Spencer Sherwin
RVRAUL VAZQUEZ
RAUL VAZQUEZ
Within the turbomachinery industry, components are currently assessed deploying standard second-order steady solvers. These are unable to capture complicated unsteady phenomena that have a critical impact on component performance. In this work, the high-order spectral h/p solver Nektar++ will be applied to a compressor blade to study the turbulent transition mechanisms and assess the effect of incoming disturbances with quasi-DNS resolution. The case will be modelled at an angle of incidence of 53.5° to match the original experimental loading at 52.8°. At clean inflow conditions, Kelvin–Helmholtz instabilities appear on both sides of the blade due to a double separation, with the pressure side one not being reported in the experiments. The separation is gradually removed by the incoming turbulent structures but at different rates on the two sides of the blade. It will be shown that there is an optimal amount of turbulence intensity that minimises momentum thickness, which is strongly related to losses. Moreover, a discussion on the spanwise extrusion will be included, this being a major player in the modelling costs. Finally, the wall-clock time and the exact expenditure to run this case will be outlined, providing quantitative evidence of the feasibility of considering a quasi-DNS resolution in an industrial setting.