Gulenay Guner

Ms. Gulenay Guner

New Jersey Institute of Technology, Newark, California, USA
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 November 2020 in AAPS PharmSciTech
Verified
Journal Article
Closed access
PDF file
Ecevit BilgiliEcevit Bilgili
Ecevit Bilgili
Gulenay GunerGulenay Guner
Gulenay Guner

10 July 2021 in Pharmaceutics
Verified
Journal Article
Open access
PDF file
Gulenay GunerGulenay Guner
Gulenay Guner
DYDogacan Yilmaz
Dogacan Yilmaz
Ecevit BilgiliEcevit Bilgili
Ecevit Bilgili
This study examined the impact of stirrer speed and bead material loading on fenofibrate particle breakage during wet stirred media milling (WSMM) via three kinetic models and a microhydrodynamic model. Evolution of median particle size was tracked via laser diffraction during WSMM operating at 3000–4000 rpm with 35–50% (v/v) concentration of polystyrene or zirconia beads. Additional experiments were performed at the center points of the above conditions, as well as outside the range of these conditions, in order to test the predictive capability of the models. First-order, nth-order, and warped-time kinetic models were fitted to the data. Main effects plots helped to visualize the influence of the milling variables on the breakage kinetics and microhydrodynamic parameters. A subset selection algorithm was used along with a multiple linear regression model (MLRM) to delineate how the breakage rate constant k was affected by the microhydrodynamic parameters. As a comparison, a purely empirical correlation for k was also developed in terms of the process/bead parameters. The nth-order model was found to be the best model to describe the temporal evolution; nearly second-order kinetics (n ≅ 2) was observed. When the process was operated at a higher stirrer speed and/or higher loading with zirconia beads as opposed to polystyrene beads, the breakage occurred faster. A statistically significant (p-value ≤ 0.01) MLRM of three microhydrodynamic parameters explained the variation in the breakage rate constant best (R2 ≥ 0.99). Not only do the models and the nth-order kinetic–microhydrodynamic correlation enable deeper process understanding toward developing a WSMM process with reduced cycle time, but they also provide good predictive capability, while outperforming the purely empirical correlation.

24 June 2021 in Pharmaceutical Research
Verified
Journal Article
Closed access
PDF file
Gulenay GunerGulenay Guner
Gulenay Guner
MKManisha Kannan
Manisha Kannan
MBMatthew Berrios
Matthew Berrios
Ecevit BilgiliEcevit Bilgili
Ecevit Bilgili

26 August 2023 in Pharmaceutics
Verified
Journal Article
Open access
PDF file
Gulenay GunerGulenay Guner
Gulenay Guner
MMMirsad Mehaj
Mirsad Mehaj
NSNatasha Seetharaman
Natasha Seetharaman
SESherif Elashri
Sherif Elashri
HYHelen Yao
Helen Yao
Ecevit BilgiliEcevit Bilgili
Ecevit Bilgili
The impacts of bead sizes and bead mixtures on breakage kinetics, the number of milling cycles applied to prevent overheating, and power consumption during the nanomilling of drug (griseofulvin) suspensions were investigated from both an experimental and theoretical perspective. Narrowly sized zirconia beads with nominal sizes of 100, 200, and 400 µm and their half-and-half binary mixtures were used at 3000 and 4000 rpm with two bead loadings of 0.35 and 0.50. Particle size evolution was measured during the 3 h milling experiments using laser diffraction. An nth-order breakage model was fitted to the experimental median particle size evolution, and various microhydrodynamic parameters were calculated. In general, the beads and their mixtures with smaller median sizes achieved faster breakage. While the microhydrodynamic model explained the impacts of process parameters, it was limited in describing bead mixtures. For additional test runs performed, the kinetics model augmented with a decision tree model using process parameters outperformed that augmented with an elastic-net regression model using the microhydrodynamic parameters. The evaluation of the process merit scores suggests that the use of bead mixtures did not lead to notable process improvement; 100 µm beads generally outperformed bead mixtures and coarser beads in terms of fast breakage, low power consumption and heat generation, and low intermittent milling cycles.

13 March 2024 in Pharmaceutics
Verified
Journal Article
Open access
PDF file
DCDonald James Clancy
Donald James Clancy
Gulenay GunerGulenay Guner
Gulenay Guner
Sayantan ChattorajSayantan Chattoraj
Sayantan Chattoraj
HYHelen Yao
Helen Yao
MFM. Connor Faith
M. Connor Faith
Ecevit BilgiliEcevit Bilgili
Ecevit Bilgili
This study aimed to develop a practical semi-mechanistic modeling framework to predict particle size evolution during wet bead milling of pharmaceutical nanosuspensions over a wide range of process conditions and milling scales. The model incorporates process parameters, formulation parameters, and equipment-specific parameters such as rotor speed, bead type, bead size, bead loading, active pharmaceutical ingredient (API) mass, temperature, API loading, maximum bead volume, blade diameter, distance between blade and wall, and an efficiency parameter. The characteristic particle size quantiles, i.e., x10, x50, and x90, were transformed to obtain a linear relationship with time, while the general functional form of the apparent breakage rate constant of this relationship was derived based on three models with different complexity levels. Model A, the most complex and general model, was derived directly from microhydrodynamics. Model B is a simpler model based on a power-law function of process parameters. Model C is the simplest model, which is the pre-calibrated version of Model B based on data collected from different mills across scales, formulations, and drug products. Being simple and computationally convenient, Model C is expected to reduce the amount of experimentation needed to develop and optimize the wet bead milling process and streamline scale-up and/or scale-out.

1 December 2021 in Advanced Powder Technology
Verified
Journal Article
Closed access
MAMohammad Azad
Mohammad Azad
Gulenay GunerGulenay Guner
Gulenay Guner
AAAfolawemi Afolabi
Afolawemi Afolabi
RDRajesh Davé
Rajesh Davé
Ecevit BilgiliEcevit Bilgili
Ecevit Bilgili