Hamid Pourasiabi

Dr. Hamid Pourasiabi

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

27 June 2022 in Tribology Transactions
Verified
Journal Article
Closed access
EDE. Demirer
E. Demirer
Hamid PourasiabiHamid Pourasiabi
Hamid Pourasiabi
JGJ.D. Gates
J.D. Gates
Particle impingement angle variations during interactions between abrasive particles and wear plates affect the wear rate and cause uneven abrasion of liners in sliding bed applications—a typical condition in ore transfer chutes. Inner circumference abrasion tests (ICAT) were performed on specimens placed at various angles to abrasive bed flow direction to analyze these effects in laboratory environments. The ICAT results indicated that wear performance diminishes for increasing impingement angles within the range studied. In all impingement angles, carbide volume fraction (CVF) showed significant direct influence on the alloy performance in contrast to Cr/C ratio of the alloy showing only minor effects. Abrasion performance versus CVF trends for white cast iron and abrasive combinations were observed to show performance reversals in the ICAT due to preferential abrasion of matrix. Abrasive type (hardness) was shown to be a factor for performance reversal in that study, with abrasive particle size being suggested to be another factor. To determine this, the current study scrutinizes coarse particle abrasion in addition to fine particle tests. Dissimilar to fine basalt, coarse particle ICAT results show monotonic wear life increase versus CVF, with no performance reversal.

10 February 2022 in Tribology Transactions
Verified
Journal Article
Closed access
EDE. Demirer
E. Demirer
Hamid PourasiabiHamid Pourasiabi
Hamid Pourasiabi
LML.J. McInnes
L.J. McInnes
RKR. Knibbe
R. Knibbe
JGJ.D. Gates
J.D. Gates
Although the trends of abrasion performance versus carbide volume fraction (CVF) of white cast irons (WCIs) have been studied to some extent, there remain gaps in understanding of the factors controlling performance. This study addresses three knowledge gaps. Firstly, the influence of testing conditions, more closely reproducing ore chute service, has been determined using the inner circumference abrasion test (ICAT), which included different natural rock types. The benefit of WCI compared to steels was much greater in basalt than in granite or greywacke. Secondly, the current work shows monotonic behavior for granite and greywacke but performance reversal in basalt, demonstrating that the reversal is not due to “more severe” or “high stress” conditions. The literature variously shows monotonic, plateauing, or reversing CVF dependence but has not convincingly explained these behaviors. Thirdly, the Cr/C ratio (previously neglected) shows no effect in granite, but lower Cr/C gives poorer performance in basalt. The trends are explained by relative responses of the microconstituents to different minerals. Basalt abrades both steel and the WCI matrix but not M7C3, thus maximizing the benefit of WCI but creating roughened surfaces with protruding carbides. This promotes carbide fracture in hypereutectic alloys and, hence, the reversal. Harder minerals create less differential and hence less protrusion and no plateau.

30 October 2022 in MethodsX
Verified
Journal Article
Open access
Hamid PourasiabiHamid Pourasiabi
Hamid Pourasiabi
JGJ.D. Gates
J.D. Gates
High-stress abrasive wear is a major material consumption process in mining and ore beneficiation industries. The common laboratory high-stress abrasion apparatuses suffer from lack of capability of closely simulating the service conditions of grinding media and mill liners, being the main consumables in these sectors. The ball mill abrasion test (BMAT) is a versatile abrasive wear tester that facilitates reliable modelling of kinematics and contact mechanics of the industrial mills. Unlike ‘standard’ test devices, natural rocks of any type and/or blend with desired particles size distributions can be charged into the BMAT for testings under various ranges of liquids, grinding media and durations. It is simple to design, low-cost to manufacture, reliable to evaluate alloys performance and reproducible to rank abrasion-resistant materials. In this work, BMAT's two operation modes, BMAT-T (tumbling mode) and BMAT-C (cassette mode) are introduced. The performed comprehensive analysis on the method development, statistical assessment and further procedures refinement showed that: • In the BMAT-T, 20-hour tests using the planned operational parameters and normalisation method result in statistically reliable and reproducible outcomes. • In the BMAT-C, four 20-hr intervals, different operational parameters and specific specimen distribution pattern are needed to obtain high quality measurements. • The maximum observed relative standard deviation in the all statistical and alloy-performance evaluation campaigns was 6.6% — an excellent quality dimension for an abrasion test.

12 December 2023 in Materials & Design
Verified
Journal Article
Open access
JGJeff Gates
Jeff Gates
Hamid PourasiabiHamid Pourasiabi
Hamid Pourasiabi
LKLaura M. Keen
Laura M. Keen
ADAlexander Dalton
Alexander Dalton
PBP.J. Bennet
P.J. Bennet
YAYahia Ali
Yahia Ali

18 November 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
EDE. Demirer
E. Demirer
Hamid PourasiabiHamid Pourasiabi
Hamid Pourasiabi
DJD. D. Jarreta
D. D. Jarreta
JGJ. D. Gates
J. D. Gates