Shale gas reservoirs generally exhibit characteristics such as low porosity, permeability, and pore throat radius, with high airflow resistance. Currently, hydraulic fracturing is a commonly used method for commercial shale gas extraction; however, the hydraulic fracturing method has exhibited a series of issues, including water sensitivity and reservoir pollution in shale reservoirs. Therefore, the development of anhydrous fracturing technology suitable for shale gas reservoirs has become an urgent requirement. The supercritical carbon dioxide fracturing technique has the merits of reducing reservoir damage, improving recovery and backflow rates, and saving water resources. Moreover, this technique has broad application prospects and can achieve the effective extraction of shale gas. To enhance the understanding of the supercritical carbon dioxide fracturing technique, this review summarizes the progress of current research on this technique. Furthermore, this study analyzes the stage control technology of supercritical carbon dioxide during the fracturing process, the interaction characteristics between supercritical carbon dioxide and rocks, and the laws of rock initiation and crack growth in supercritical carbon dioxide fracturing. The outcomes indicate that after SC-CO2 enters the reservoir, CO2 water–rock interaction occurs, which alters the mineral composition and pore throat framework, weakens the mechanical characteristics of shale, reduces the rock fracturing pressure, and increases the complexity of the fracturing network. This article provides a reference for research related to supercritical carbon dioxide fracturing technology and is greatly significant for the development of shale gas reservoirs.
With the increasing demand for deep oil and gas exploration and CCUS (Carbon Capture, Utilization, and Storage) engineering, improving rock-crushing efficiency stands as a pivotal technology. Ultrasonic vibration-assisted drilling has emerged as a novel rock-breaking technology. The high-frequency vibrations of ultrasonic waves impact rocks, inducing resonance and accelerating their fragmentation. At the same time, ultrasonic waves generate cavitation bubbles in the liquid near rock surfaces; the expansion and collapse of these bubbles further contribute to rock damage, thereby improving crushing efficiency. Therefore, investigating the dynamics and failure characteristics of cavitation bubbles near rock surfaces under ultrasonic influence is crucial for advancing ultrasonic-assisted rock-breaking technology. This study treats the liquid as compressible flow and investigates the movement and rupture of bubbles near rock surfaces under varying ultrasonic parameters, rock properties, characteristics of the circulating medium, and other relevant factors. The findings show that ultrasonic waves induce the oscillation, translation, collapse, and rebound of bubbles near rock surfaces. Higher ultrasonic frequencies correspond to larger collapse pressures and amplitudes near surrounding rocks, as well as longer expansion times and shorter collapse durations. In addition, bubble movement and collapse lead to rock material deformation, influenced by the rheological properties of the liquid medium. The study outcomes serve as a foundation for optimizing engineering parameters in ultrasonic-assisted rock breaking and provide theoretical support for the advancement of this technology.
During the drilling process, cuttings settle under the action of gravity, which easily results in the formation of a cuttings bed, which then results in wellbore cleaning problems. The settling law of cuttings in drilling fluid is essentially a problem of solid–liquid two-phase settling. This study analyzes and summarizes the effects of the wall effect, the rheology of the fluid, particle shape irregularity, and particle concentration on the settling rate of particles and clarifies the problems faced by current research on the settling rate of particles and the development direction. Studies have shown that walls exert additional blocking effects on particles, thus reducing their settling velocity. The shear thinning effect of non-Newtonian fluids such as power-law fluids and Herschel–Bulkley fluids will reduce the viscosity of the liquid, thus increasing the settling velocity of the particles. Compared with spherical particles, irregular particles will obtain higher resistance in the fluid, leading to a decline in the particle settling velocity. The mutual interference between particles will result in an increase in the drag force on the particles and a decline in the settling velocity. However, when the particles are aggregated, the settling velocity will increase. This study can provide theoretical guidance for predicting the migration law of cuttings during the drilling of horizontal wells, and it has important significance for enriching the theory of solid–liquid two-phase flow.
The settlement drag coefficient of non-spherical particles (SDCNPs) is a crucial parameter in the field of petroleum engineering. Accurately predicting the SDCNPs in the fluid is essential to the selection and design of proppant and hydraulic design in the fracturing scheme. Although many models for anticipating the SDCNPs have been proposed, none of them can be adopted for non-Newtonian fluid (NNF) and Newtonian fluid (NF). In the investigation, the SDCNPs in NF and NNF are studied experimentally, and the anticipation mode of the settlement drag coefficient of spherical particles (SDCSPs) in different fluids (including Newton, Herschel-Bulkley and power law) is proposed. On this basis, the shape depiction parameter circularity is introduced to develop the SDCNPs. The results exhibit that the predicted values of the SDCNPs model perfectly align with the experimental values, and the average relative errors are 5.70%, 6.24% and 6.72%, respectively. The mode can accurately describe the settlement behavior of non-spherical particles (NSPs) and provide a basis for the application of NSPs in petroleum engineering.
In modern oil and gas exploration and development, wellbore trajectory optimization and control is the key technology to improve drilling efficiency, reduce costs, and ensure safety. In the drilling operation of non-vertical wells in complex formations, the traditional static trajectory function, combined with the classical optimization algorithm, has difficulty adapting to the parameter fluctuation caused by formation changes and lacks real-time performance. Therefore, this paper proposes a wellbore trajectory optimization model based on deep reinforcement learning to realize non-vertical well trajectory design and control while drilling. Aiming at the real-time optimization requirements of complex drilling scenarios, the TD3 algorithm is adopted to solve the problem of high-dimensional continuous decision-making through delay strategy update, double Q network, and target strategy smoothing. After reinforcement learning training, the trajectory offset is significantly reduced, and the accuracy is greatly improved. This research shows that the TD3 algorithm is superior to the multi-objective optimization algorithm in optimizing key parameters, such as well deviation, kickoff point (KOP), and trajectory length, especially in well deviation and KOP optimization. This study provides a new idea for wellbore trajectory optimization and design while drilling, promotes the progress and development of intelligent drilling technology, and provides a theoretical basis and technical support for more accurate, efficient, concise, and effective wellbore trajectory optimization and design while drilling in the future.
Complex fracture technology is key to the successful development of unconventional oil and gas reservoirs, such as shale. Most current studies focus on how to improve the complexity of the fracture network. It is still unclear whether proppant can enter the branch fractures at all levels after the formation of complex fractures. The effects of construction displacement, proppant particle size, proppant density, fracturing fluid viscosity, sand ratio, and other factors on proppant migration in single fractures and complex fractures were studied using an experimental device independently developed by the laboratory. The results show that the lowest point height of the sandbank and the equilibrium height of the sandbank are directly proportional to the particle concentration and density, respectively, and inversely proportional to the displacement and fracturing fluid viscosity. The equilibrium time of the sandbank is inversely proportional to the displacement, particle concentration, and density, respectively, and proportional to the viscosity of the fracturing fluid. Under the same experimental conditions, the larger the branch angle, the smaller the height of the main/secondary fracture sandbank. In the design of the fracturing process, fracturing fluid with varying viscosities and proppant with different densities should be selected according to the formation conditions and fracturing targets. In the face of long fracture lengths, the combination of low-viscosity fracturing fluid with an appropriate viscosity and low-density proppant can meet the goal of placing proppant over long distances and effectively supporting fractures over extended lengths. Subsequently, high-density proppant or reduced construction displacement are adopted to usefully support fractures in the near-wellbore area. The results of this paper can provide theoretical support for proppant selection and fracturing program design.