Smart grids are complex electrical systems made up of power devices and communication systems that interact with each other, both locally through measures and generally through the exchange of information on communication networks. In this article, the simulation of a smart grid including the emulation of the communication network behavior together with the physical hardware devices is proposed using Hardware-in-the-Loop methodology. The original aspect of the technique is related to the fact that the models are generated in a tool that is independent of the real-time simulator using a model-based design approach, then the code is generated and deployed in a real-time simulator coupled with hardware devices such as low voltage protection units. The proposed framework is used to test the protection coordination that employs the IEC-61850 communication protocol. A test case is shown demonstrating the coordination of switches and the emulation of the PV system in Hardware-in-the-Loop, focusing on the implementation of the interface algorithm over Ethernet using the UDP communication protocol.
Due to the increasing use of smart components in smart grids, interoperability among them is a crucial aspect to address. IEC61850 is a communication standard that has been already used in substations because of its instant data transfer and the ability to enable data exchange between a variety of smart energy-related digital technologies. This article studies the application of the communication protocols defined by the IEC61850 standard in Intelligent Electronic Devices (IEDs) by using a prototype testbed architecture running on a real-time digital device. The goal of this activity is to study the impact of smart simulations and the vulnerability in terms of cyber-security. This testbed includes the supervisor, the substation bus, and the process bus communication layer creating a local network exchanging data at distinct levels. Different fault protection scenarios are discussed using both physical and emulated IEDs, and the communication protocols implemented in each scenario are explained showing that additional delays are introduced. In the first two scenarios, the operation of the testbed using physical versus emulated IEDs is analyzed and compared, ensuring the robustness of this methodology in situations where the use of a physical IED would be unfeasible. In these scenarios, the functionality and robustness of the protection mechanisms and communication protocols are confirmed. In the third scenario vulnerability of smart grids that use IEC61850 as their primary communication protocol to data injection attacks is studied. Sniffing the local network, packets are captured and monitored. Spoofed data with the same structure are injected into the network to conduct false data injection attacks on the supervisory unit. Vulnerability to cyber attacks of the IEC61850 protocol in specific situations is shown.
Deterministic load flow analyses of power grids do not include the uncertain factors that affect the network elements; hence, their predictions can be very unreliable for distribution system operators and for the decision makers who deal with the expansion planning of the power network. Adding uncertain probability parameters in the deterministic load flow is vital to capture the wide variability of the currents and voltages. This is achieved by probabilistic load flow studies. Photovoltaic systems represent a remarkable source of uncertainty in the distribution network. In this study, we used a Gaussian copula to model the uncertainty in correlated photovoltaic generators. Correlations among photovoltaic generators were also included by exploiting the Gaussian copula technique. The large sets of samples generated with a statistical method (Gaussian copula) were used as the inputs for Monte Carlo simulations. The proposed methodologies were tested on two different networks, i.e., the 13 node IEEE test feeder and the non-synthetic European low voltage test network. Node voltage uncertainty and network health, measured by the percentage voltage unbalance factor, were investigated. The importance of including correlations among photovoltaic generators is discussed.
The idea of this paper is to present a Real Time Simulation Framework coupling a modeling environment such as Matlab Simulink to a Real Time Hardware like National Instrument MyRio. The idea is to draft an implementation example of Hardware in the loop simulation for teaching goals. The simulation of PV system including control strategy has to cope with different constraints. The former is the solution of the DAE system required by the PV that is strongly nonlinear. The latter is the fast simulation of the dynamic control strategy, such as the case of Maximum Power Point Tracking Algorithm. In the middle several other requirements, including the hardware in the loop Simulation.
This article presents an optimal distributed energy resource management system for a smart grid connected to photovoltaics, battery energy storage, and an electric vehicle aggregator. These management systems are one of the key factors for the optimal control of power converters connected to the grid. The proposed management system includes the communication architecture necessary for realizing the information flow between the individual control of the distributed generators and the master supervisory control algorithm. The work carried out on two levels is first to design a control strategy for energy management and validate it with the grid in real-time hardware-in-the-loop simulation integrating the IEC61850 communication layer and physical intelligent electronic devices. The second is to analyze the vulnerabilities of the designed methodology for cybersecurity threats explicitly with the extension of IEC61850 to electric vehicle aggregators for communication with the master energy management. A man-in-the-middle attack conducted in the supervisory communication layer enabled us to investigate the effects of such an attack on the performance and operation of the smart electric grid.
Distributed generation such as photovoltaic is more encouraged by government policies to exploit the renewable energy resource and for sustainable energy production. The integration of photovoltaic generation to the distribution network introduces large uncertainties, the inclusion of these uncertainties in load flow analysis used for planning, operation, and expansion of the power system networks is done by using the probabilistic load flow studies approach. With this, the risk identification and its mitigation associated with the power network can be easily performed. In this work, the modeling of photovoltaic generation based on historical data that is obtained by power system measurements is presented. The distribution of photovoltaic generation obtained is complex and does not match any standard distributions. A numerical method is used to generate the samples that are used for Monte Carlo simulation to include photovoltaic generation with its original characteristics and uncertainties in probabilistic analysis. The analysis is done by integrating a 1000 kW photovoltaic generation system in IEEE 13 Node Test Feeder, which is highly loaded and unbalanced. As a function of a photovoltaic generation uncertainty, statistical distribution of variables such as currents and voltage of each network elements are calculated. Using them, the network health and the power loss associated with the network are determined.