This study aims to clarify the removal mechanism and to calculate the effective current of electrocoagulation (i.e., EC) for treating wastewater containing Ni(II), Cu(II), and Cr(VI). The adsorption behavior of various heavy metals onto Al(OH)3 coagulant generated by the EC process was investigated and the estimating method of the corresponding current was established. Results indicate that adsorption of single Ni(II) and Cu(II) by Al(OH)3 coagulant can be simulated by the Langmuir isotherm, while Cr(VI) adsorption fits the Freundlich isotherm better. As treating single heavy metal of wastewater, the removal mechanism of the EC process is the adsorption reaction. Under the coexisting condition, the Ni(II) and Cu(II) will compete for the same active sites on the Al(OH)3 surface and Cu(II) suppresses Ni(II) adsorption. As treating the coexisting heavy metals, Ni(II) removal not only associates with adsorption but also with the coprecipitation. In contrast, Cr(VI) does not compete with other metal ions for the same type of adsorption sites. Whether single or coexisting conditions, the adsorption capacity of heavy metals onto Al(OH)3 coagulants can be used to compute the necessary current to effectively remove heavy metals in the EC system.
19 September 2020 in Journal of Inorganic and Organometallic Polymers and Materials
A series of experiments with different NaCl concentrations added to the PCB (printed circuit board) wastewater were prepared to investigate the chloride effect on the formation of aluminum floc and removal efficiency of Cu and Ni. The effects of pH, current density, and different concentration of NaCl were studied and the results are discussed. Results imply that chloride ions are favored to avoid the passivation of the aluminum anode in the EC (electro-coagulation) system. Chloride ions used as the electrolyte can facilitate the release of Al3+, which results in the current efficiency of over 100% in the EC system. For the PCB factory’s wastewater, the EC system could remove Cu2+ and Ni2+ effectively (both Cu and Ni concentration of treated wastewater was less than 1.0 mg/L within three minutes). PCB wastewater’s pH value could maintain stably about 9.0 in the EC system when the initial pH value was around 2.5. The estimated electricity consumption for treating PCB wastewater by the EC process was about 0.894 kWh for each meter of cubic wastewater.
Graphene oxide (GO) and reduced graphene oxide (rGO) are promising materials for sustainable energy storage due to their excellent conductivity, large surface area, and chemical stability. However, conventional methods of reducing GO often involve toxic chemicals, raising environmental concerns. This study introduces a green solvothermal method to synthesize rGO using L-ascorbic acid and ammonia solution as reducing agents, producing a material referred to as G-rGO for supercapacitor applications. Theoretical calculations suggest that the reduction process significantly enhances the electronic properties and structural integrity of the material. X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and energy-dispersive X-ray (EDX) analysis confirmed the reduction of GO to G-rGO. Electrochemical tests, including cyclic voltammetry (CV), galvanostatic charge/discharge (GCD), and electrochemical impedance spectroscopy (EIS), demonstrated that G-rGO performed exceptionally well. It exhibited a high specific capacitance of 401 F/g at 1 A/g and impressive cycle stability of 93% after 10,000 cycles. Theoretical results indicate that these characteristics are attributed to enhanced charge transport and a favorable surface area-to-volume ratio. Additionally, G-rGO achieved an energy density of 200.5 Wh/kg at a power density of 2.5 W/kg, underscoring its potential as an eco-friendly, high-performance electrode material for sustainable energy storage.
In both the inorganic and organic worlds, carbon-based nanomaterials, such as benzene, diamond, graphite, fullerene, and carbon nanotubes, are abundant. In science laboratories, carbon is the focal point of activity. In this overview, the synthesis, characteristics, and several uses of graphene—including energy conversion, energy storage, electronics, and biosensing—were explored with a focus on ecologically friendly production techniques. This article also discusses recent advancements in the detection and treatment of organic contaminants and heavy metals utilizing nanomaterials. In this article, we outline some recent developments in the creation of innovative nanomaterials and nanostructures and methods for treating organic contaminants and heavy metals in water. The essay presents the current state of the field and, in our opinion, should be helpful to anybody interested in nanomaterials and related materials.