The transformation of conventional binder and grout into high-performance nanocarbon binder and grout was evaluated in this investigation. The high-performance nanocarbon grout consisted of grey cement, white cement, lime, gypsum, sand, water, and graphite nanoplatelet (GNP), while conventional mortar is prepared with water, binder, and fine aggregate. The investigated properties included unconfined compressive strength (UCS), bending strength, ultrasound pulse analysis (UPA), and Schmidt surface hardness. The results indicated that the inclusion of nanocarbon led to an increase in the initial and long-term strengths by 14% and 23%, respectively. The same trend was observed in the nanocarbon binder mortars with white cement, lime, and gypsum in terms of the UCS, bending strength, UPA, and Schmidt surface hardness. The incorporation of nanocarbon into ordinary cement produced a high-performance nanocarbon binder mortar, which increased the strength to 42.5 N, in comparison to the 32.5 N of the ordinary cement, at 28 days.
Reducing the crack width is a vital feature for protecting rebars from corrosion. In this investigation, the impact of steel fibres (SFs) on the cracking of recycled coarse aggregate reinforced concrete (RCARC) beams was investigated. Twenty-seven reinforced concrete (RC) experimental samples (150 mm × 200 mm × 1500 mm) were manufactured. Shear rebars were considered with different spacings. Specimens were tested under a four-point flexural setup. Recycled coarse aggregate (RCA) from a destroyed building was employed at 0%, 50% and 100% by weight. SFs were added at three contents (0%, 1% and 2%) in order to reduce the crack width. The mid-span load–displacement relationship and the crack propagation and width were measured during the tests. Therefore, this study intended to assess the impact of utilising RCA and natural coarse aggregate on cracks’ spacing and propagation in RC beams when SFs were employed. The obtained outcomes were compared with the requirements of CSA S474, NS 3473E, EC2-04, CEB-FIP and ACI 224R-01. It was found that enough shear rebars should be provided through the beams to control the crack width and propagation, but that SFs enhanced the bending performance of RCARC with no shear rebars.
16 August 2022 in Advances in Structural Engineering
Triple Friction Pendulum Isolators (TFPIs) have been widely used to enhance the seismic capacity of structures in the recent decade. This study intends to measure the effect of different Ground Motion (GM) sets, including Far-Fault (FF) and Near-Fault (NF) records, on the seismic response of the Triple Friction Pendulum (TFP) isolated structures. For this aim, different Engineering Demand Parameters (EDP), including Inter-story Drift Ratio (IDR), absolute floor acceleration, base shear, residual displacement, and damage energy are measured using numerous Nonlinear Time History (NTH) analyses. A three-dimensional mid-rise special moment resisting frames (SMFs) steel building isolated with TFPIs has been designed as per ASCE 7-16. In addition, the separate and simultaneous effect of raising the damping ([ ]) and the period ([ ]) of the base isolation system on the seismic responses of the superstructure are measured to assess the structural performance and estimate the damage energy. The [ ] and the [ ] are amplified up to 30% and 4.5 times of the superstructure period in incremental steps, respectively. The results show that the damage energy of the superstructure in the Initial Design Parameters' Values (IDPVs) of the isolator under NF records with Forward-Directivity pulses (NF-FD-GMs) is more significant than damping energy, while an inverse trend has occurred for other GM sets. Increasing the IDPVs up to a certain level reduces most EDPs and consequently causes an improvement in the seismic performance of the superstructure. The novel developed empirical relationships can be utilized as useful tools to predict IDRs and the damage states of the superstructure. The variations of the EDPs with respect to simultaneous or separate increasing the IDPVs are also reported for different GM sets.
Steel-concrete-steel (SCS) sandwich panels are manufactured with two thin high-strength steel plates and a moderately low-density and low-strength thick concrete core. In this study, 24 specimens were produced and tested. In these specimens, a new stud-bolt connector was used to regulate its shear behaviour in sandwich panels. The bolts’ diameter, concrete core’s thickness and bolts’ spacing were the parameters under analysis. Furthermore, the concrete core was manufactured with normal-strength concrete and steel fibres concrete (SFC). Steel fibres were added at 1% by volume. In addition, the recycled coarse aggregate was used at 100% in terms of mass instead of natural coarse aggregate. Therefore, the ultimate bearing capability and slip of the sandwich panels were recorded, and the failure mode and ductility index of the specimens were evaluated. A new formula was also established to determine the shear strength of SCS panels with this kind of connectors. According to this study, increasing the diameter of the stud-bolts or using SFC in sandwich panels improve their shear strength and ductility ratio.
Most isolators have numerous displacements due to their low stiffness and damping properties. Accordingly, the supplementary damping systems have vital roles in damping enhancement and lower the isolation system displacement. Nevertheless, in many cases, even by utilising additional dampers in isolation systems, the occurrence of residual displacement is inevitable. To address this issue, in this study, a new smart type of bar hysteretic dampers equipped with shape memory alloy (SMA) bars with recentring features, as the supplementary damper, is introduced and investigated. In this regard, 630 numerical models of SMA-equipped bar hysteretic dampers (SMA-BHDs) were constructed based on experimental samples with different lengths, numbers, and cross sections of SMA bars. Furthermore, by utilising hysteresis curves and the corresponding ideal bilinear curves, the role of geometrical and mechanical parameters in the cyclic behaviour of SMA-BHDs was examined. Due to the deficiency of existing analytical models, proposed previously for steel bar hysteretic dampers (SBHDs), to estimate the first yield point displacement and post-yield stiffness ratio in SMA-BHDs accurately, new models were developed by the artificial neural network (ANN) and group method of data handling (GMDH) approaches. The results showed that, although the ANN models outperform GMDH ones, both ANN- and GMDH-based models can accurately estimate the linear and nonlinear behaviour of SMA-BHDs in pre- and post-yield parts with low errors and high accuracy and consistency.