The use of condensers in air conditioning units is more common in large-capacity units than in ones with a smaller capacity. Air conditioning provides comfort and freshness to an air-conditioned room. It should be noted that each room has a different heat load, which affects the specifications of the condenser used. The accuracy with which appropriate condenser specifications are determined affects the performance of the air conditioner. Thus, considering how important condenser needs are, it is necessary to design condensers with optimal performance, which adhere to proven standards. To achieve this, the design of a condenser should be based on the results of the smallest condenser dimensions of three types of surfaces, as they are intended for a limited place. This condenser design uses the standard dimensions of the Kays and London charts. Data is collected by measuring the results of temperature and enthalpy of a refrigerant at desuperheating and condensation, inlet air temperature, outlet air temperature, refrigerant mass flow rate, and air mass flow rate. The results of the compact condenser design are based on existing data, which is obtained from the smallest design results. The result uses the type of Surface CF-8.72(c) with a heat transfer area of 0.259 m2, a total tube length of 9.5 m, crossing tube length 0.594 m and a pressure drop of 3778 Pascal (Pa) on the side of a tube. This design fulfills the stipulated requirements, as the pressure drop is less than the specified maximum limit in most units.
29 November 2018 in IOP Conference Series: Materials Science and Engineering
In this paper, numerical simulation of distortion and phase transformation in laser welding process is carried out. A coupled thermal-structural and metallurgical model of laser welding process is simulated by using FEA engineering software MSC Marc/Mentat. The specimen model is simulated in the form of butt joint plate with dimension 50 mm in length and 25 mm in width with 2 mm thickness and using material low carbon steel (C15). Conical heat source model implemented in this simulation due to existing Goldak's double ellipsoid commonly used for arc welding process. Phase transformation is predicted based on Seyyfarth-Kassatkin Model and implemented in user subroutine PLOTV which is written in FORTRAN programming language. Presented results of laser welding simulation included temperature distribution, phase transformation, and estimated welding distortion.
Traffic violations and road accidents remain significant challenges in developing safe and efficient transportation systems. Despite technological advancements, improving vehicle detection accuracy and enabling real-time traffic management remain critical research priorities. This study proposes YOLO-LIO, an enhanced vehicle detection framework designed to address these challenges by improving small-object detection and optimizing real-time deployment. The system introduces multi-scale detection, virtual zone filtering, and efficient preprocessing techniques, including grayscale transformation, Laplacian variance calculation, and median filtering to reduce computational complexity while maintaining high performance. YOLO-LIO was rigorously evaluated on five datasets, GRAM Road-Traffic Monitoring (99.55% accuracy), MAVD-Traffic (99.02%), UA-DETRAC (65.14%), KITTI (94.21%), and an Author Dataset (99.45%), consistently demonstrating superior detection capabilities across diverse traffic scenarios. Additional system features include vehicle counting using a dual-line detection strategy within a virtual zone and speed detection based on frame displacement and camera calibration. These enhancements enable the system to monitor traffic flow and vehicle speeds with high accuracy. YOLO-LIO was successfully deployed on Jetson Nano, a compact, energy-efficient hardware platform, proving its suitability for real-time, low-power embedded applications. The proposed system offers an accurate, scalable, and computationally efficient solution, advancing intelligent transportation systems and improving traffic safety management.
A classifier plays a crucial role in the cement industry. It is in charge of separating coal that has been smoothened out and is ready to be burned although the coal is still rough after going through the grinding process. It takes a long time to burn coal that is not perfectly processed with a classifier. Therefore, it will reduce the amount of cement production, and the factories will release more energy. The closed arrangement and the number of components in the unit classifier requires a sophisticated method to detect damage that occurs early. Vibration analysis is a method that has been effectively employed in detecting the initial damage that occurs to the engine, especially the classifier. This study was aimed at detecting the location of the damage occurring in the classifier by using a vibration signal analysis and by measuring the magnitude of vibration and presenting it to the frequency domain (spectrum) form using Fast Fourier Transform. Engine condition assessment referred to ISO 10816-3 standard in velocity and displacement modes. Based on data spectrum analysis, the dominant damage laid in the unbalanced rotor. Spectrum characteristics of the damage appeared to be in the spectrum line worth 438.01 μm at a 3.5-Hz frequency (1X) radially. This analysis proved to be supported by the decrease in vibration value to 18.65 μm after balancing the Classifier rotor.
1 October 2024 in International Journal of Innovation in Mechanical Engineering and Advanced Materials
This study investigates the influence of water hyacinth fiber length and content on the torsional strength of epoxy resin composites. Utilizing an experimental design, specimens were prepared with varying fiber lengths (10 mm, 20 mm, 25 mm, and 135 mm) and content percentages (4%, 7%, and 10%) and subjected to torsional testing according to ASTM E-143 standards. The primary objective was to determine the optimal fiber configurations that enhance the composite's mechanical properties, particularly its resistance to torsional stress. Results indicated that shorter fiber lengths consistently yielded higher torsional strength, with the 20 mm fibers at a 7% content displaying the highest torque resistance, achieving a maximum of 1.418 Nm and a shear stress of 29.348 MPa. In contrast, longer fibers generally showed diminished performance, likely due to poorer resin penetration and fiber-matrix bonding. Regression analysis was employed to develop predictive models for the torsional behavior based on fiber dimensions and compositions, achieving high accuracy with coefficients of determination (R²) ranging from 0.95 to 1.00, suggesting excellent model fits. These findings underscore the potential of using water hyacinth fibers as effective reinforcement in epoxy composites, particularly at optimal lengths and concentrations. The study contributes to the broader utilization of natural fibers in composites, offering a sustainable alternative to synthetic fibers with beneficial mechanical properties and environmental impacts.
31 May 2023 in International Journal of Innovation in Mechanical Engineering and Advanced Materials
Cast wheel rims often experience damage that causes damage to the lip of the rim, or the spokes rupture if it supports the excessive load. The safety aspect is very important to be considered in the automotive industry because it involves the lives of passengers. Structural optimization of various vehicle components has shown that component weight strongly influences vehicle performance. Based on these problems, this research aims to design a lightweight cast wheel design model that can withstand a load of 535 N. So, it is necessary to make an analysis using a comparison of design models and material variations and static simulations using Solidworks 2018 software. The results sought are von mises, displacement, strain, a factor of safety, and produce a lightweight design. The simulation results on the three models are still safe in holding a load of 535 N because the value of the factor of safety is not less than 1. The results of the design mass with material variations are lighter than the original wheels.