Petr Kotrbacek

Prof. Dr. Petr Kotrbacek

Brno University of Technology, Heat Transfer and Fluid Flow Laboratory
orcid

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2000 in Materials & Design (1980-2015)
Verified
Journal Article
Closed access
ATA Tseng
A Tseng
JHJaroslav Horský
Jaroslav Horský
HBHana Bellerova
Hana Bellerova
Petr KotrbacekPetr Kotrbacek
Petr Kotrbacek

21 September 2020 in Metals
Verified
Journal Article
Open access
PDF file
MCMartin Chabicovsky
Martin Chabicovsky
Petr KotrbacekPetr Kotrbacek
Petr Kotrbacek
HBHana Bellerova
Hana Bellerova
JKJan Kominek
Jan Kominek
HBHana Bellerova
Hana Bellerova
This study considers spray cooling starting at surface temperatures of about 1200 °C and finishing at the Leidenfrost temperature. Cooling is in the film boiling regime. The paper uses experimental techniques for the study of which spray parameters are necessary for good prediction of spray cooling intensity. The research is based on experiments with water and air-mist nozzles. The following spray parameters were measured together with a heat transfer coefficient: water flowrate, water impingement density, impact pressure, droplet size and velocity. Derived parameters as droplet kinetic energy, droplet momentum and droplet Reynolds number are used in the tested correlations as well. Ten combinations of spray parameters used for correlation functions for the heat transfer coefficient (HTC) are studied and discussed. Correlation functions for prediction of HTC are presented and it is shown which spray parameters are necessary for reliable computation of HTC. The best results were obtained when the parameters impact pressure and water impingement density were used together. It was proven that the correlations based only on water impingement density, which are the most frequent in literature, can not provide reliable results.

12 July 2021 in Polymers
Verified
Journal Article
Open access
PDF file
JKJan Kominek
Jan Kominek
MZMartin Zachar
Martin Zachar
MGMichal Guzej
Michal Guzej
Erik BartuliErik Bartuli
Erik Bartuli
Petr KotrbacekPetr Kotrbacek
Petr Kotrbacek
Miniaturization of electronic devices leads to new heat dissipation challenges and traditional cooling methods need to be replaced by new better ones. Polymer heat sinks may, thanks to their unique properties, replace standardly used heat sink materials in certain applications, especially in applications with high ambient temperature. Polymers natively dispose of high surface emissivity in comparison with glossy metals. This high emissivity allows a larger amount of heat to be dissipated to the ambient with the fourth power of its absolute surface temperature. This paper shows the change in radiative and convective heat transfer from polymer heat sinks used in different ambient temperatures. Furthermore, the observed polymer heat sinks have differently oriented graphite filler caused by their molding process differences, therefore their thermal conductivity anisotropies and overall cooling efficiencies also differ. Furthermore, it is also shown that a high radiative heat transfer leads to minimizing these cooling efficiency differences between these polymer heat sinks of the same geometry. The measurements were conducted at HEATLAB, Brno University of Technology.

16 November 2020 in Steel Research International
Verified
Journal Article
Closed access
PDF file
Petr KotrbacekPetr Kotrbacek
Petr Kotrbacek
HBHana Bellerova
Hana Bellerova
TLTomas Luks
Tomas Luks
HBHana Bellerova
Hana Bellerova

28 February 2007 in Revue de Métallurgie
Verified
Journal Article
Closed access
PDF file
MRM. Raudensky
M. Raudensky
AHA. Horak
A. Horak
JHJ. Horsky
J. Horsky
MPMichal Pohanka
Michal Pohanka
Petr KotrbacekPetr Kotrbacek
Petr Kotrbacek
New dynamic features of the descaling process are reported, referringto the continuous water jet formed by the descaling nozzle in particular.A water jet is formed by clusters of droplets moving at highvelocity. In the impact area, pressure peaks of several hundred MPa,lasting microseconds per peak are observed: this is described as the effect. This finding modifies most existing conceptsof descaling and the impact on current theory is discussed.

1 August 1998 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
JHJ Horský
J Horský
HBHana Bellerova
Hana Bellerova
Petr KotrbacekPetr Kotrbacek
Petr Kotrbacek