In order to achieve the European Commission’s ambitious climate targets by 2030, BEVs (Battery Electric Vehicles) manufacturers are faced with the challenge of producing more efficient and ecological products. The electromechanical powertrain plays a key role in the efficiency of BEVs, which is why the design parameters in the development phase of electromechanical powertrains must be chosen carefully. One of the central design parameters is the maximum speed of the electric machines and the gear ratio of the connected transmissions. Due to the relationship between speed and torque, it is possible to design more compact and lighter electric machines by increasing the speed at constant power. However, with higher speed of the electric machines, a higher gear ratio is required, which results in a larger and heavier transmission. This study therefore examines the influence of maximum speed on the power density of electromechanical powertrains. Electric machines and transmissions with different maximum speeds are designed with the state-of-the-art for a selected reference vehicle. The designs are then examined with regard to the power density of the overall powertrain system. Compared to the reference vehicle, the results of the study show a considerable potential for increasing the power density of electromechanical powertrains by increasing the maximum speed of the electric machines.
Increasing the speed of the electric motor can significantly improve the power density of the powertrain of EVs (Electric Vehicles), resulting in a smaller size and thus weight and cost advantages. Achieving acceptable NVH behavior becomes more difficult at higher speeds, partly because the excitation frequencies of the gears cover a wider frequency range and therefore higher natural frequencies can also be directly excited. In the Speed4E joint research project, a high-speed electromechanical powertrain was developed, manufactured, and tested to investigate the main challenges on the NVH- and efficiency-behavior of high-speed powertrains. The high-speed design of the Speed4E drivetrain results in maximum electric motor speeds of up to 50,000 rpm, combined with a torque of up to 45 Nm at the transmission input shafts. This study presents the experimental results on the vibration behavior of the high-speed planetary gearbox, a comparison with the corresponding results of a highly efficient calculation method of the gearbox vibration excitation, and the theoretical background of the calculation method is presented. The results indicate the potential to improve the vibration behavior of high-speed drives in EVs and provide a deep understanding of the challenges associated with high speeds.
One of the central goals during the design of helical gear systems is the achievement of a well-distributed contact load in the gear mesh. An equal load distribution is a key factor for a high load carrying capacity, the economic use of materials and a long lifetime. Mesh misalignment can be caused by tooth deflections, manufacturing deviations or elastic deformation of the shaft-bearing system and the gearbox housing. Those deformations have to be taken into account during the design process of adequate tooth-flank geometry. Elastic deformations of gearbox housings can be significant, especially in the case of automotive applications with aluminium cases. This paper presents an advanced method of including housing stiffness into the calculation of gear systems. A validation of the approach is carried out by comparing the calculated deformations with measurements of a static test rig of a hypoid gearbox.Many calculation programs offer the opportunity to analyse the deformation behaviour of the shaft-bearing-housing system. Most of the components in these programs are described by analytic approaches. However, components that are geometrically more complex, like the housing or planet carriers cannot be represented as easily as that by analytic expressions. There are several alternatives to take into account the elasticity of those objects. One way is to model the stiffness of the bores using imported stiffness matrices. These matrices contain the elasticity of the bores itself as well as crossover influences between the bearings. The reduced stiffness matrices may be the result of a static reduction of the geometry using the finite element method (FEM). As state of the art, the reduction is mostly carried out at the centre points of the bearing bores. The proposed advanced method uses the static reduction of geometries on several points at the bores, distributed over the circumference. This approach offers a more detailed modelling of the elastic behaviour of complex geometries within the analytic deformation calculation of gear systems. To validate the advanced approach, the calculation results of the elastic deflections of the shaft-bearing-housing system is compared with measurements of a static test rig. In the course of these comparisons, the influence of different modelling methods of gearbox housings on the accuracy of the calculation results is discussed.
High-speed electric drive units promise improved power density and, theoretically, driving range of battery electric vehicles. An essential step of the development process is extensive testing of the drive unit on a test rig. In particular, at a high rotational speed level, experimental testing can be challenging. This paper describes a test rig for investigating the overall function of a high-speed drive unit and the transmission’s efficiency and dynamics. The high-speed drive unit developed in the Speed4E research project was the reference drive unit. The test rig is based on the concept of electrical power circulation. Thus, the test rig can be used universally for different drive unit designs and operating modes. A reaction torque measurement unit was developed to enable measurements at high rotational speeds. Simultaneously, this unit allows robust measurements at low costs. The expected measurement uncertainties of torque, rotational speed, transmission efficiency, and power losses were calculated using the Monte Carlo method. The results demonstrate that the developed torque measurement unit combines precise torque measurement with a robust design and low costs, making it competitive with state-of-the-art solutions for torque measurement at high speeds.
Planetary gear sets combine the characteristics of high-power density and compact design which are beneficial for a wide range of high-performance applications. Embedded in the efforts for resource efficiency and cost reduction, new challenges arise regarding a lightweight design. An accurate prediction of the load sharing on the individual planetary gears and especially of the load distribution of the meshing gears is of major importance. A uniform load distribution enables the design of the individual tooth meshes without load increases and oversizing. However, a varying load distribution has been observed in planetary gearboxes with respect to the rotation of the carrier which is caused by misaligned central shafts of the gearbox. This behavior is influenced by several factors, such as manufacturing and assembly deviations, the rigidity of shafts, housing and bearings, the number of planets, the quality of the gear wheels and the operating conditions. To determine the exact load distribution, detailed simulations or extensive experimental prototype tests are required. In an early design phase, these detailed boundary conditions are not yet defined and their effect on a moving contact pattern therefore cannot be reliably considered.Thus, in this paper an experimental investigation of the influencing factors on a varying load distribution with regard to the carrier rotation is presented. Based on experimental data recommendations for the design of planetary gearboxes are derived.