The paper presents the research of plastic expansion of a pipe workpiece by punches of various configurations. It is shown that interest in this process is caused by the development of oil production, where there is a need to increase the diameter of well pipes, the automobile industry, where the protection of the driver and passengers in case of accidents comes first. Here, stable plastic deformation plays an important role as a good absorber of kinetic energy, etc. Data on the problems of expanding pipe ends are given, where special attention is paid to the destruction of the end in the form of localization of deformations and appearance of a longitudinal crack. To eliminate this phenomen onvarious technological methods are used. Here the influence of the design and shape of the punch on the localization of deformations along the thickness of the workpiece is researched. Several spatial outlines of the tool are proposed to create an effective reloading of the pipe workpiece in the deformation zone. Based on numerical modeling, the distribution of stresses according to Mises, the displacement of the end of the semi-finished product and logarithmic deformations in the radial direction is shown for each standard size of the punch. Comparative results reveal an increase in the thickness of the workpiece in the dangerous section for all presented punches. The comparison was carried out with a reference tool that has a straight generatrix of a tapered surface. The best results are shown by a punch with an enlarged generatrix at the end of the working stroke. Attention is focused on conducting further research in order to study the possibility of overcritical deformation by the proposed tool.
20 June 2018 in International Journal of Engineering & Technology
The article deals with the main technological problems arising in the manufacture of large-scale ceramic products for architectural and artistic purposes. The influence of low-burned chamotte obtained from low-alumina clay on the physical and mechanical properties of molding masses based on the Oposhnya clays is investigated. It is shown that the firing medium of the developed molding masses significantly affects the properties of ceramic products.
29 December 2021 in Eastern-European Journal of Enterprise Technologies
This paper shows that the technological preparation of production accounts for 20‒70 % of the total labor intensity of technical preparation. An important role belongs to the applied programs of finite-element modeling. However, such software packages often cannot be purchased by small-scale industrial enterprises for various reasons. Therefore, special empirical and analytical calculation models are used, which have proved to be quite effective in typical metal processing processes. Drawing a cylindrical hollow part was used as an example of the improved analytical dependence to calculate meridional tensile stresses. Existing analytical models of the process accounted for the bending moment through additional stresses. However, this approach only roughly described the deformation process. It was possible to refine the existing analytical dependences by introducing a term into the differential equilibrium equations that takes into consideration the bending moment that acts in the meridional direction when a workpiece passes the rounding on the matrix edge. Analysis of the obtained expression revealed that the bending of a workpiece gives rise to the stretching meridional stresses, which depend on the ratio of the squares of the thickness of the workpiece and the radius of the matrix rounding. The results of the estimation data from the numerical and theoretical models coincided for small values of the radius of the matrix rounding of 1‒2 mm, which confirms the adequacy of the analytical solution. In the numerical model, there is an extreme point where the tensile stresses have a minimum and, after it, begin to increase; this corresponds to the matrix rounding radius of 5 mm
The Ukrainian Industry 4.0 strategy envisages the positioning of Ukraine as a high-tech, post-industrial country, integrated into global technological chains of value creation and producing unique engineering services and high-quality products. In particular, for the needs of the territorial communities of Ukraine in the conditions of war, the uninterrupted operation of agro-food supply chains and ensuring the ecological safety of these territories has become especially important. This paper explores the possibilities of creating a unified digital information space in a modern cloud-based enterprise resource planning (ERP) system to improve the management of all subjects in the territorial community and facilitate the transition to the Industry 4.0 technology landscape.
29 September 2023 in Scientific Progress & Innovations
У машинобудуванні спостерігається стійка тенденція виготовлення металевих великогабаритних виробів із вуглецевих сталей із захисними корозійностійкими неметалевими покриттями поверхонь, контактуючих із агресивним середовищем, що дозволяє відмовитися від використання дорогих нікель-хром-молібденових сталей і спеціальних сплавів типу хастелой, реманіт та інші. При цьому процес дробоструминної підготовки робочих поверхонь, для нанесення на них таких покриттів, грає головну технологічну роль, оскільки забез-печує міцність зчеплення захисного покриття з металевою основою виробу. Пропонується роботизована система дробоструминної обробки вільних поверхонь виробів, яка складається з мобільного роботизованого модуля, прецизійно-електронного засобу сканування оброблювальної поверхні й центрального мікро- контрольного модуля керування комплексом. Подана удосконалена технологія дробоструминного очищення з повною ув’язкою технічних характеристик створеної автоматизованої системи і взаємо- узгоджених заданих і наслідкових параметрів дробоструміння. Система дозволяє проводити дистанційну обробку металевих поверхонь вільних об'ємно-просторових форм (корпуси ракет, фюзеляжі літальних апа-ратів, резервуари для зберігання токсичних рідин, корпуси торпед, корпуси хімічних, біологічних, харчових, медичних та інших ємнісних апаратів, корпуси кораблів і підводних човнів) з дотриманням високої продуктивності, якості обробки, мінімізації енергетичних і економічних показників та екологічної безпеки. Практична цінність розробки виявляється при виготовленні ємкісних виробів, що експлуатуються в особливих умовах і потребують надійного захисту від руйнівного агресивного впливу хімічно активних середовищ, високих тисків та температур. Запропоновані техніко-технологічні рішення можуть бути використані в оборонній та цивільно-промисловій галузях як високотехнологічна та економічно виправдана альтернатива іншим методам очистки і поширеній трудомісткій ручній праці з підготовки та корозійного захисту металевих поверхонь виробів. Запропонована автоматизована система дробоструминної обробки забезпечить такі основні переваги: підвищення якості обробки вільних поверхонь металевих виробів; можливість онлайн-моніторингу центральним мікроконтролерним пристроєм за станом оброблюваної поверхні; енергоощадливість; екологічна безпека; універсальність; мінімізація впливу людського фактору на процес; зменшення технологічного часу на обробку виробу.
30 October 2025 in Таврійський науковий вісник. Серія: Технічні науки
Значна частина території України з поверхні перекрита шаром лесових відкладів різної потужності. Ці відклади характеризуються особливими властивостями – вони володіють просіданням у сухому (твердому) стані, а при зволоженні переходять у категорію так званих «слабких» ґрунтів зі значною стисливістю. Ці особливості зумовлені процесами утворення лесових відкладів і можуть бути пояснені гіпотезами їх утворення. Леси утворюють декілька горизонтів, що пов’язано з періодами зледеніння на нашій планеті і перешаровуються з глинистими ґрунтами, що утворились у періоди потепління. З цієї точки зору характерною є будова Полтавського лесового плато, на якому можна виділити 2–3 «поверхи» лесових відкладів, верхній з яких розташований на глибині 4–9 м від поверхні. Зважаючи на інтенсивний розвиток будівництва, зміну конструктивних рішень будівель, збільшення поверховості, збільшення навантажень, проектувальники змушені використовувати пальові фундаменти збільшуючи довжину та розміри поперечного перерізу паль, що значно збільшує вартість та терміни будівництва. Тому одним із надійних та економічних рішень у цьому випадку є застосування підсилення основ, складених такими ґрунтами. Одним із надійних та ефективних способів підсилення додавання у ґрунт в’яжучої речовини. Такі процеси можуть виконуватися за різними технологіями – звичайна, напірна та струменева цементація, одно-, дво-, та триструменеві, JET-технології тощо. Однак у кожної з цих технологій є свої переваги і недоліки, що дозволяє їх застосовувати в одних випадках та робить неефективними у інших. Тому для вирішення проблеми закріплення ґрунтів було вибрано бурозмішувальну технологію, яка дозволяє контролювати якість утворення ґрунтоцементної суміші, виконувати підбір необхідної кількості води для оптимізації консистенції суміші та регулювати об’єм цементного розчину. Залежно від особливостей інженерно-геологічних умов розроблено технологію влаштування ґрунтоцементних елементів постійного та змінного поперечного перерізу, що дозволяє застосовувати такий метод підсилення як у сухих, так і в обводнених ґрунтах.