Kangsu Lee

Dr. Kangsu Lee

Korea Insitute of Ships and Ocean Engineering
+1
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2019 in Journal of Ocean Engineering and Technology
Verified
Journal Article
Open access
PDF file
SPSugn-Ju Park
Sugn-Ju Park
Kangsu LeeKangsu Lee
Kangsu Lee
Jae Hoon SeoJae Hoon Seo
Jae Hoon Seo
JCJoonmo Choung
Joonmo Choung

Verified
Journal Article
Open access
PDF file
KSKichan Sim
Kichan Sim
Kangsu LeeKangsu Lee
Kangsu Lee
A digital twin is a virtual model of a real-world structure (such as a device or equipment) which supports various problems or operations that occur throughout the life cycle of the structure through linkage with the actual structure. Digital twins have limitations as a general simulation method because the characteristic changes (motion, stress, vibration, etc.) that occur in the actual structure must be acquired through installed sensors. Additionally, it takes a huge computing cost to output changes in the structure’s characteristics in real time. In particular, in the case of ships and offshore structures, simulation requires a lot of time and resources due to the size of the analysis model and environmental conditions where the wave load acts irregularly, so the application of a different simulation methodology from existing ones is required. The order reduction method, which accurately represents the system’s characteristics and expresses them in a smaller model, can significantly reduce analysis time and is an effective option. In this study, to analyze the applicability of the order reduction method to the development of digital twins for offshore structures, the structural responses of a multi-connected floating offshore structure were estimated by applying the order reduction method based on distortion base mode. The order reduction method based on the distortion base mode predicts the responses by constructing an order-reduced conversion matrix consisting of the selected distortion base mode, based on the mode vector’s orthogonality and autocorrelation coefficients. The predicted structural responses with the reduced order model (ROM) were compared with numerical analysis results derived using the higher order boundary element method and finite element method with in-house code owned by the Korea Research Institute of Ship & Ocean Engineering and measured responses with a model test. When compared with the numerical analysis results, the structural responses were predicted with high accuracy in the wave direction and wave frequency band of the selected distortion base mode, but there are differences due to changed characteristics of the structure when compared with the results of the model test. In addition, differences were also seen in reduced order model evaluation with different sensor locations, and it was confirmed that the more similar the extracted distortion base modes of input sensor location set is to the distortion base modes of predicted location set, the higher accuracy is in predicting the structural responses. As a result, the performance of the reduced order model is determined by the distortion base mode selection method, the locations of the sensor, and the prediction for the structural response.

3 September 2024 in International Journal of Naval Architecture and Ocean Engineering
Verified
Journal Article
Open access
Kangsu LeeKangsu Lee
Kangsu Lee
KSKichan Sim
Kichan Sim

18 February 2020 in Structural and Multidisciplinary Optimization
Verified
Journal Article
Closed access
PDF file
MMMin-Yeong Moon
Min-Yeong Moon
HKHyun-Seok Kim
Hyun-Seok Kim
Kangsu LeeKangsu Lee
Kangsu Lee
BPByoungjae Park
Byoungjae Park
KCK.K. Choi
K.K. Choi

30 April 2021 in Journal of Ocean Engineering and Technology
Verified
Journal Article
Open access
PDF file
DLDong Jun Lee
Dong Jun Lee
Chang-Yong SONGChang-Yong SONG
Chang-Yong SONG
Kangsu LeeKangsu Lee
Kangsu Lee
μud,s : static upper bound design friction coefficient (0.3)

31 December 2023 in Journal of Ocean Engineering and Technology
Verified
Journal Article
Open access
PDF file
KSKichan Sim
Kichan Sim
Kangsu LeeKangsu Lee
Kangsu Lee
BKByoung Wan Kim
Byoung Wan Kim
Recently, offshore structures for eco-friendly energy, such as wind and solar power, have been developed to address the problem of insufficient land space; in the case of energy generation, they are designed on a considerable scale. Therefore, the scalability of offshore structures is crucial. The Korea Research Institute of Ships & Ocean Engineering (KRISO) developed multi-linked floating offshore structures composed of floating bodies and connection beams for floating photovoltaic systems. Large-scale floating photovoltaic systems are mainly designed in a manner that expands through the connection between modules and demonstrates a difference in structural response with connection conditions. A fluid–structure coupled analysis was performed for the multi-linked floating offshore structures. First, the wave load acting on the multi-linked offshore floating structures was calculated through wave load analysis for various wave load conditions. The response amplitude operators (RAOs) for the motions and structural response of the unit structure were calculated by performing finite element analysis. The effects of connection conditions were analyzed through comparative studies of RAOs and the response’s maximum magnitude and occurrence location. Hence, comparing the cases of a hinge connection affecting heave and pitch motions and a fixed connection, the maximum bending stress of the structure decreased by approximately 2.5 times, while the mooring tension increased by approximately 20%, confirmed to be the largest change in bending stress and mooring tension compared to fixed connection. Therefore, the change in structural response according to connection condition makes it possible to design a higher structural safety of the structural member through the hinge connection in the construction of a large-scale multi-linked floating offshore structure for large-scale photovoltaic systems in which some unit structures are connected. However, considering the tension of the mooring line increases, a safety evaluation of the mooring line must be performed.