Aldo German Benavides-Moran

Prof. Dr. Aldo German Benavides-Moran

Mechanical and Mechatronics Engineering, Universidad Nacional de Colombia, Bogotá, Colombia
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2008 in Powder Technology
Verified
Journal Article
Open access
Aldo German Benavides-MoranAldo German Benavides-Moran
Aldo German Benavides-Moran
BWBerend van Wachem
Berend van Wachem
This work describes a theoretical and numerical study of turbulent gas–particle flows in the Eulerian framework. The equations describing the flow are derived employing Favre averaging. The closures required for the equations describing the particulate phase are derived from the kinetic theory of granular flow. The kinetic theory proposed is extended from its original form to incorporate the effects of the continuous fluid on the particulate phase behavior. Models describing the coupling between the continuous phase kinetic energy and particulate phase granular temperature are derived, discussed, and their effect on the flow predictions is shown. The model is validated by comparing its predictions to experiments of fully developed turbulent gas–solid pipe flow. As shown in Fig. 1, there is very good qualitative and quantitative agreement between the simulation results and the experimental data. The presence of a dispersed phase clearly modifies the gas-phase behavior, as illustrated in Fig. 1, when comparing the profiles for a single-phase flow (clear gas) to the particle-laden flow cases. It has also been shown that an increase in the solid-phase concentration significantly dampens the gas-phase velocity fluctuations far from the pipe wall; this is in accordance with experimental observations.

10 January 2020 in Drying Technology
Verified
Journal Article
Closed access
Aldo German Benavides-MoranAldo German Benavides-Moran
Aldo German Benavides-Moran
ACAlfonso Cubillos
Alfonso Cubillos
AGAlexánder Gómez
Alexánder Gómez
This paper presents a computational fluid dynamics (CFD) approach to model the spray-drying of a formulation of guava juice. The computational model incorporates the characteristic drying rate curve (CDC) of the formulation. The CDC is derived from the drying history of single droplets suspended on a thin glass filament. The computational domain is based on the geometry of a small production spray-dryer with a capacity of 10 kg/h. A two-phase Eulerian-Lagrangian model implemented in a commercial CFD package (ANSYS-FLUENT) is used to simulate the gas-particle interaction in the dryer. Hot-wire anemometry (HWA) measurements of the air flow in the drying chamber are used to calibrate the CFD model. The URANS k-ω SST and the Scale-Adapted Simulation turbulence models are employed to compute the unsteady three-dimensional flow field. Model calibration suggests that the swirl number of the air flow entering the dryer is about 0.61. Simulations predict high axial velocities along the center-line and a narrow jet core in the upper part of the dryer. Lagrangian particle tracking is used to calculate the particle trajectories starting from the perimeter of the rotary disk atomizer and ending at the dryer walls and bottom outlet. Simulation results of particle size distribution, time-average temperature and humidity profiles are presented in order to analyze the overall drying performance. The procedure shown in this work emphasizes the need of implementing drying kinetics with experimental support, and suitable inlet flow conditions to perform detailed CFD simulations of the spray-drying of fruit juices.

1 June 2009 in International Journal of Heat and Fluid Flow
Verified
Journal Article
Closed access
Aldo German Benavides-MoranAldo German Benavides-Moran
Aldo German Benavides-Moran
BWBerend van Wachem
Berend van Wachem

1 August 2017 in Powder Technology
Verified
Journal Article
Open access
CLCasey Q. LaMarche
Casey Q. LaMarche
Aldo German Benavides-MoranAldo German Benavides-Moran
Aldo German Benavides-Moran
BWBerend van Wachem
Berend van Wachem
JCJennifer Sinclair Curtis
Jennifer Sinclair Curtis
The Two-Fluid Method is capable of modeling large-scale (i.e., lab scale or larger) multiphase (particle-fluid) flows by treating both the fluid and particle phase as interpenetrating continua and solving mass and momentum balances for each phase. To solve for the flow of the solids phase the momentum balance requires constitutive relations in the form of normal and shear stresses – i.e., pressures and viscosities. However, the stresses that account for frictional contacts in dense particle systems, and are relevant to this work, are empirically based. A study of the effects of adjusting the frictional model formulation (the empirical parameters of the model), by changing the overall frictional stress magnitude and the relative magnitude of the frictional viscosity to the frictional pressure, on the behavior of the bed is presented here. It was found that the magnitude of the frictional viscosity relative to the frictional pressure affects the crater growth prediction almost as much as the magnitude of the overall frictional stress. Additionally, a frictional model formulation is validated for sand particles, and predictions are compared with existing experimental data for the crater formation of a sand bed under a vertical, impinging jet of gas (Metzger et al. J Areo Eng (2008) v22, p24–32). In the low jet velocity regime (subsonic, turbulent jet), the model predicts the salient features previously measured for the growth rate of the crater of time, the profile of the crater, and the response of the crater to turning the jet off. In the high jet velocity regime (compressible, near sonic jet flow) the prediction agrees qualitatively with prior experimental observations

30 December 2021 in Processes
Verified
Journal Article
Open access
PDF file
Aldo German Benavides-MoranAldo German Benavides-Moran
Aldo German Benavides-Moran
LRLuis Rodríguez-Jaime
Luis Rodríguez-Jaime
Santiago LainSantiago Lain
Santiago Lain
This paper presents computational fluid dynamics (CFD) simulations of the flow around a horizontal axis hydrokinetic turbine (HAHT) found in the literature. The volume of fluid (VOF) model implemented in a commercial CFD package (ANSYS-Fluent) is used to track the air-water interface. The URANS SST k-ω and the four-equation Transition SST turbulence models are employed to compute the unsteady three-dimensional flow field. The sliding mesh technique is used to rotate the subdomain that includes the turbine rotor. The effect of grid resolution, time-step size, and turbulence model on the computed performance coefficients is analyzed in detail, and the results are compared against experimental data at various tip speed ratios (TSRs). Simulation results at the analyzed rotor immersions confirm that the power and thrust coefficients decrease when the rotor is closer to the free surface. The combined effect of rotor and support structure on the free surface evolution and downstream velocities is also studied. The results show that a maximum velocity deficit is found in the near wake region above the rotor centerline. A slow wake recovery is also observed at the shallow rotor immersion due to the free-surface proximity, which in turn reduces the power extraction.

1 December 2013 in Ingeniare. Revista chilena de ingeniería
Verified
Journal Article
Open access
PDF file
RGRicardo Gelves
Ricardo Gelves
Aldo German Benavides-MoranAldo German Benavides-Moran
Aldo German Benavides-Moran
JQJuan Carlos Quintero
Juan Carlos Quintero