To address the freeze-thaw (F-T) durability of concrete structures in severely cold plateau regions, this study investigates recycled coarse aggregate concrete (RCAC) by designing mixtures with varying replacement ratios of recycled brick aggregate (RBA). Rapid freeze-thaw cycling tests are conducted in combination with macro- and microscale analytical techniques to systematically elucidate the frost resistance and damage mechanisms of mixed recycled coarse aggregate concrete. When the RBA content is 50%, the concrete demonstrates relatively better frost resistance within the mixed recycled aggregate system. This is evidenced by the lowest mass loss rate coupled with the highest retention ratios for both the relative dynamic elastic modulus (RDEM) and the compressive strength. Micro-analysis indicates that an appropriate amount of RBA can optimize the pore structure, exerting a “micro air-cushion” buffering effect. Blending RBA with recycled concrete aggregate (RCA) may create functional complementarity between pores and the skeleton, effectively delaying freeze–thaw damage. A GM (1,1) damage prediction model based on gray system theory is established, which demonstrates high accuracy (R2 > 0.92). This study provides a reliable theoretical basis and a predictive tool for the durability design and service life assessment of mixed recycled coarse aggregate concrete engineering in severely cold regions.
To address the high carbon emissions and resource dependency associated with conventional ordinary Portland cement (OPC) production, this study systematically investigated the preparation processes, hydration mechanisms, and chemical properties of high-belite calcium sulfoaluminate (HBCSA) and calcium sulfoaluminate (CSA) cements based from industrial solid wastes. The results demonstrate that substituting natural raw materials (e.g., limestone and gypsum) with industrial solid wastes—including fly ash, phosphogypsum, steel slag, and red mud—not only reduces raw material costs but also mitigates land occupation and pollution caused by waste accumulation. Under optimized calcination regimes, clinkers containing key mineral phases (C4A3S− and C2S) were successfully synthesized. Hydration products, such as ettringite (AFt), aluminum hydroxide (AH3), and C-S-H gel, were identified, where AFt crystals form a three-dimensional framework through disordered growth, whereas AH3 and C-S-H fill the matrix to create a dense interfacial transition zone (ITZ), thereby increasing the mechanical strength. The incorporation of steel slag and granulated blast furnace slag was found to increase the setting time, with low reactivity contributing to reduced strength development in the hardened paste. In contrast, Solid-waste gypsum did not significantly differ from natural gypsum in stabilizing ettringite (AFt). Furthermore, this study clarified key roles of components in HBCSA/CSA systems; Fe2O3 serves as a flux but substitutes some Al2O3, reducing C4A3S− content. CaSO4 retards hydration while stabilizing strength via sustained AFt formation. CaCO3 provides nucleation sites and CaO but risks AFt expansion, degrading strength. These insights enable optimized clinker designs balancing reactivity, stability, and strength.
3 December 2025 in Construction and Building Materials
This study systematically evaluates the influence of the recycled coarse aggregate (RCA) replacement rate and the number of freeze–thaw cycles (FTCs) on the frost damage of recycled aggregate concrete (RAC) through rapid freeze–thaw tests, and delves into the underlying damage mechanisms. The findings demonstrate that the incorporation of recycled aggregates deteriorates the frost resistance of concrete to a certain extent, primarily manifested by increased apparent damage with rising FTC numbers and RCA content. Specimens with an RCA replacement rate exceeding 50% exhibited extensive mortar spalling and aggregate exposure after 50 FTCs. The mass loss rate initially decreased in the early freezing-thawing stage, then began to increase after approximately 20 cycles, reaching a maximum of 5.09%. The relative dynamic elasticity modulus (RDEM) decreased with an increase in both FTCs and RCA content, dropping to a minimum of 71.99%. Furthermore, based on the relative dynamic elastic modulus, this study developed a GM(1, 1) freeze–thaw damage prediction model applicable to a full replacement range of 0%–100% RCA with a precision level of Grade I. Microstructural analysis revealed that microcracks and pores within the interfacial transition zones (ITZs) and the surrounding matrix of both NCA and RCA are critical for the initiation and propagation of freeze–thaw damage, thereby elucidating the damage mechanism in RAC.
21 November 2025 in Construction and Building Materials