There are several parameters that must be set before manufacturing a product using 3D printing. These parameters include the orientation deposition of that product, type of material, form fill, fill density, and other parameters. The finished product of 3D printing has some responses that can be observed, measured, and tested. Some of those responses are the processing time, the dimensions of the end product, its surface roughness and the mechanical properties, i.e. its yield strength, ultimate tensile strength, and impact resistance. This research was conducted to study the relationship between process parameters of 3D printing machine using a technology of fused deposition modeling (FDM) and the generated responses. The material used was ABS plastic that was commonly used in the industry. Understanding the relationship between the parameters and the responses thus the resulting product can be manufactured to meet the user needs. Three different orientations in depositing the ABS polymer named XY(first orientation), YX (second orientation), and ZX (third orientation) were studied. Processing time, dimensional accuracy, and the product strength were the responses that were measured and tested. The study reports that the printing process with third orientation was the fastest printing process with the processing time 2432 seconds followed by orientation 1 and 2 with a processing time of 2688 and 2780 seconds respectively. Dimension accuracy was also measured from the width and the length of gauge area of tensile test specimens printed in comparison with the dimensions required by ASTM 638-02. It was found that the smallest difference was in thickness dimension, i.e. 0.1 mm thicker in printed sample using second orientation than as required by the standard. The smallest thickness deviation from the standard was measured in width dimension of a sample printed using first orientation (0.13 mm). As with the length dimension, the closest dimension to the standard was resulted from the third orientation product, i.e 0.2 mm. Tensile test done on all the specimens produced with those three orientations shows that the highest tensile strength was obtained in sample from second orientation deposition, i.e. 7.66 MPa followed by the first and third orientations products, i.e. 6.8 MPa and 3.31 MPa, respectively
Kelurahan Nginden Jangkungan merupakan salah satu bagian dari Kelurahan di Wilayah Kecamatan Sukolilo Kota Surabaya yang berada pada provinsi Jawa Timur dimana Kelurahan ini terkenal dengan sebutan Kampung Herbal.Di Kampung Herbal ini, penduduk setempat memanfaatkantanah aset pemerintah kota yang dulu merupakan rawa dengan membudidayakan tanaman herbal. Permasalahan yang ditemukan adalah banyaknya sampah penduduk dan ranting kayu dan dedaunan di lingkungan sekitar yang belum termanfaatkan secara menyeluruh dengan optimal yang dapat menyebabkan lingkungan sekitar menjadi tercemar berupa bau yang tidak sedap, banjir, dan bahkan mendatangkan berbagai penyakit. Selain itu, kebutuhan akan pupuk organik untuk budidaya tanaman yang berada di kampung herbal membutuhkan biaya operasional yang tidak sedikit untuk pemenuhan kecukupan nutrisi tanaman yang ada di Kampung Herbal tersebut. Solusi permasalahan yang dapat dilakukan untuk mengatasi hal tersebut adalah perlunya pengadaan mesin kompos organik untuk mengendalikan sampah supaya tidak tercemar dan perlunya pengadaan pupuk organik sendiri mendukung budidaya tanaman yang digunakan untuk proses pembimbitan dan pemenuhan nutrisi bagi tanamanan herbal tersebut dengan biaya yang murah dan terjangkau termasuk menciptakan Ruang Terbuka Hijau (RTH). Adapun metode pelaksanaan dilakukan dengan beberapa tahapan antara lain melakukan diskusi dan tanya jawab, melakukan peninjauan lapangan, melakukan sosialisasi dan pendampingan cara pembuatan pupuk kompos organik, melakukan proses perajangan, serta melakukan proses komposting secara kimiawi. Pada akhir tahapan ditunjukkan kinerja optimal mesin kompos yang telah berhasil melakukan proses perajangan mandiri secara sempurna dalam ukuran paling kecil berkisar 63% dari target awalnya 60% sebagai bahan dasar untuk proses komposting guna menghasilkan pupuk kompos organik yang berkualitas.
1 February 2021 in IOP Conference Series: Materials Science and Engineering
Waste plastic bottle can be a pollutant that can damage the environment. If this waste plastic bottle is not well controlled, it will certainly harm the sustainability of other ecosystems. Usually, waste plastic bottle is difficult to decompose naturally, and even if it will be decomposed, it will take a long time, from 100 to 500 years. The main source of waste plastic bottle is usually the use of plastic material itself, which it is used to inseparable support in everyday life. In general, the use of plastic material has several considerations such as: lightweight, corrosion resistance, non-toxicity, friction and impact resistance, chemical resistance, good thermal stability, and good insulation properties. The general form of this product is disposable plastic bottles in drinking water. Waste plastic bottles are usually used for disposables product. Referring to this condition, they can assume and increase over a certain period the number of waste plastic bottles, where as plastic bottles are the largest source of pollutants on earth. To control this condition, it is necessary to develop a sustainable mechanism of press machine for flatting the waste plastic bottle into sheet plastic before being crushed and recycled into other products. Based on the observation of test results, it was found that the design of press machine for waste plastic bottle works with electric motor well, before being reprocessed.
6 November 2023 in Prima Abdika: Jurnal Pengabdian Masyarakat
Uncontrolled population growth and urban displacement will continue to be the causes of the rise in garbage. Waste that accumulates for too long and becomes dense and scattered will cause pollution, i.e., the spread of pests and unwanted odors. The Abdimas team sees the role of compost houses as an optimal solution to provide knowledge or education while growing public interest and awareness of the importance of garbage control and reusing it to increase the economic value of partners and communities. The purpose of this activity is for the community to be able to have a positive impact on the establishment of other composite houses around it. The activities were conducted in the form of training and supporting workshops at the PCU Composite House, and follow-up of the implementation results was conducted through the visit of the Abdimas team at the location of the partner as a post-execution evaluation of the activities. Implementation of this activity is divided into three stages, namely: preparation of training, implementation of the training, and non-continued application of training results at the partner site. The training event is packed with the topic "Organic Composite Making Skills Upgrading Training". Based on the observations of the visits carried out by the Abdimas team, one of the partners is currently working on the construction of a new composite house, while the other partner site has already implemented fertilizer production activity for the fulfillment of the element of charity for the partners' crops. The construction of compost houses and garbage banks has proven to help in controlling household trash while providing economic value for partners.
6 October 2025 in Jurnal Pengabdian Masyarakat Bhinneka
Sampah plastik, terutama gelas dan botol sekali pakai, menjadi masalah utama di Kampung Herbal Jangkungan, Surabaya. Hal ini karena sulit disimpan, membutuhkan ruang besar, dan sulit diangkut, membuat petugas bank sampah tidak dapat melakukan pekerjaan mereka dengan efisien. Tujuan program pengabdian kepada masyarakat ini adalah untuk meningkatkan efisiensi pengelolaan sampah plastik melalui penggunaan teknologi tepat guna dan partisipasi warga. Untuk memperkuat sistem pengelolaan berbasis komunitas, Bank Sampah Kampung Herbal didirikan untuk meningkatkan pengetahuan warga tentang pentingnya pengelolaan sampah, memberikan pelatihan teknis pemilahan, dan mendampingi penggunaan mesin pencacah screw press yang dibuat untuk mengatasi keterbatasan lahan. Adanya mesin screw press diharapkan meningkatkan efisiensi penyimpanan dan transportasi, mengurangi volume sampah plastik, dan meningkatkan kesadaran masyarakat akan lingkungan yang ramah lingkungan.
Pesatnya perkembangan mobil listrik membuat banyak produsen otomotif berlomba mengembangkan teknologi mobil listrik mereka sendiri. Dari sisi pengaturan performa, mobil listrik lebih banyak menyediakan fleksibilitas daripada mobil konvensional, sehingga implementasi kontrol yang lebih mutakir menjadi lebih memungkinkan. Saat ini salah satu sistem kontrol yang tersedia dan dikembangkan pada mobil listrik adalah Torque Vectoring. Pada penelitian ini dilakukan pengembangan algoritma sistem Torque Vectoring beserta sistem kontrolnya melalui pemodelan dan simulasi MATLAB-Simulink. Metode kontrol yang digunakan adalah kontroler PID. Variabel yang diukur untuk melihat keefektivitas sistem Torque Vectoring adalah yaw rate, sudut kemudi, sudut sideslip, traksi pada setiap ban, percepatan longitudinal dan lateral, kecepatan longitudinal, slip longitudinal di setiap ban, dan torsi output di setiap roda. Dari penelitian ini dapat disimpulkan bahwa algoritma sistem Torque Vectoring yang dikembangkan mampu meningkatkan stabilitas pengendalian mobil listrik. Sistem Torque Vectoring tersebut mampu beroperasi pada berbagai kondisi jalan dan manuver mobil, sehingga mobil dengan sistem Torque Vectoring lebih dapat dikendalikan dan stabil jika dibandingkan dengan mobil tanpa sistem Torque Vectoring.
About Me
Lecturer at Mechanical Engineering Department, Petra Christian University
Lecturer at Mechanical Engineering Department, Petra Christian University