Jacek Szmagliński

Dr. Jacek Szmagliński

Gdańsk University of Technology, Faculty of Civil and Environmental Engineering
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2021 in Science of The Total Environment
Verified
Journal Article
Open access
Nicole NawrotNicole Nawrot
Nicole Nawrot
Ewa WojciechowskaEwa Wojciechowska
Ewa Wojciechowska
KPKsenia Pazdro
Ksenia Pazdro
Jacek SzmaglińskiJacek Szmagliński
Jacek Szmagliński
JPJanusz Pempkowiak
Janusz Pempkowiak
The study presents results from 6 months of phytoremediation of sediments dredged from three urban retention tanks carried out in a mesocosm setup with the use of P. australis. Two kinds of P. australis seedlings were considered: seedlings originating from natural (uncontaminated - Suncont) and anthropogenically changed environments (contaminated - Scont); this distinction was reflected in the baseline concentrations of trace metals inside their tissues. The potentially toxic elements (PTEs) considered in this study were as follows: Zn, Cu, Cd, Ni, Cr, and Pb. The aim of the study was to compare the uptake, accumulation, and translocation properties of seedlings with different initial trace metal contents. The PTE concentrations were analyzed in sediments as well as in belowground and aboveground parts of plants in the middle (3rd month) and at the end of the investigation period using inductively coupled plasma mass spectrometry (ICP-MS), and the accumulation of PTEs in plant tissues was calculated. Phytoextraction efficiency was evaluated using the bioconcentration factor (BF) and translocation factor (TF). Plant morphology was assessed with scanning electron microscopy (SEM) to document plant stress due to PTE exposure. The results of our study indicated that P. australis seedlings originating from sites differing in the initial trace metal content exhibited different behavior when grown on sediments dredged from urban retention tanks. Suncont seedlings with low initial metal contents tended to adapt to the dredged sediments and showed phytoextraction ability, while Scont seedlings originating from sites with initial high contents of trace metals acted as phytoexcluders and tended to release PTEs from their tissues into the sediments. The morphological and structural effects caused by metal toxicity were observed in growth limitation, root tissue disturbance, root hair number decrease, and structural alterations in the epidermis and endodermis. Therefore, the Suncont seedlings presented better properties and adaptability for phytoremediation purposes.

4 September 2020 in Remote Sensing
Verified
Journal Article
Open access
PDF file
Cezary SpechtCezary Specht
Cezary Specht
AWAndrzej Wilk
Andrzej Wilk
WKWladyslaw Koc
Wladyslaw Koc
KKKrzysztof Karwowski
Krzysztof Karwowski
PDPawel S. Dabrowski
Pawel S. Dabrowski
RLRoksana Licow
Roksana Licow
The problem of the reproduction of the railway geometric layout in the global spatial system is currently solved in the form of measurements that use geodetic railway networks and also, in recent years, efficient methods of mobile positioning (mainly satellite and inert). The team of authors from the Gdańsk University of Technology and the Maritime University in Gdynia as part of the research project InnoSatTrack is looking for effective and efficient methods for the inventory of railway lines. The research is part of a wider investigation BRIK (Research and Development in Railway Infrastructure, in polish: Badania i Rozwój w Infrastrukturze Kolejowej). This paper presents a comparative analysis of the problem of the reproduction of the trajectory of the measuring system using tacheometry, satellite measurements made using a measurement trolley, and mobile satellite measurements. Algorithms enabling the assessment of the compliance of satellite measurements with classic tacheometric measurements were presented. To this end, the authors held measurement sessions using modern geodetic instruments and satellite navigation on a section of the railway line. The results of the measurements indicate the convergence of the level of accuracy achieved by different measuring techniques.

4 September 2020 in Sensors
Verified
Journal Article
Open access
PDF file
AWAndrzej Wilk
Andrzej Wilk
WKWladyslaw Koc
Wladyslaw Koc
Cezary SpechtCezary Specht
Cezary Specht
SJSlawomir Judek
Slawomir Judek
KKKrzysztof Karwowski
Krzysztof Karwowski
Jacek SzmaglińskiJacek Szmagliński
Jacek Szmagliński
The article discusses an important issue in connection with the technique of mobile Global Navigation Satellite System (GNSS) measurements of railway track coordinates, which is digital filtering performed to precisely determine railway track axes. For this purpose, a measuring technique is proposed which bases on the use of a measuring platform with a number of appropriately distributed GNSS receivers, where two of them determine the directional base vector of the platform. The receivers used in the research had high measuring frequency in the Real Time Kinematic (RTK) operating mode and enabled correction of the obtained results in post–processing. A key problem discussed in the article is the method for assessing the quality of the measurement results obtained from GNSS receivers, and their preparation for further processing making use of geometrically constrained parameters of the base vector and specialized digital filtering, among other elements, to precisely determining the track axis. The obtained results confirm the applicability of the used method of GNSS signal processing.

1 April 2021 in Measurement
Verified
Journal Article
Closed access
AWAndrzej Wilk
Andrzej Wilk
WKWładysław Koc
Władysław Koc
CSCezary Specht
Cezary Specht
JSJacek Skibicki
Jacek Skibicki
SJSlawomir Judek
Slawomir Judek
SGSławomir Grulkowski
Sławomir Grulkowski

1 October 2019 in Journal of Konbin
Verified
Journal Article
Open access
PDF file
MBMarcin Budzyński
Marcin Budzyński
Jacek SzmaglińskiJacek Szmagliński
Jacek Szmagliński
KJKazimierz Jamroz
Kazimierz Jamroz
KBKrystian Birr
Krystian Birr
SGSławomir Grulkowski
Sławomir Grulkowski
JWJoanna Wachnicka
Joanna Wachnicka
Analysis of Gdańsk tram network statistics shows that incidents are quite frequent (about 650 within five years) and mostly involve collisions and crashes. As well as reducing the tram systems’ efficiency and reliability, incidents have a negative effect on road safety. As Polish cities extend their tram networks, they must also ensure that their existing networks are safe. This is to be achieved by conducting safety assessments. The article presents different assessment methods, at different stages of tram infrastructure lifecycle, providing a basis for a comprehensive diagnosis and recommendations for improvement. The objective of the study was to conduct a comprehensive safety assessment and analysis of the existing and planned tram network across Gdańsk, using different study methods and tools.

Verified
Journal Article
Open access
PDF file
PDPawel S. Dabrowski
Pawel S. Dabrowski
Cezary SpechtCezary Specht
Cezary Specht
AFAndrzej Felski
Andrzej Felski
WKWladyslaw Koc
Wladyslaw Koc
AWAndrzej Wilk
Andrzej Wilk
Jacek SzmaglińskiJacek Szmagliński
Jacek Szmagliński
When used at sea, satellite compasses are capable of determining the course of a sailing vessel with high accuracy. It is difficult to verify the accuracy declared by the device manufacturer under such conditions, as it is difficult to define a reliable reference. This study analyses the accuracy of the satellite compass in an urban setting, with the satellite signal being obscured to various extents. It is an important point in the study to refer the measurement results to a reference route, which is the axis of a tramway track, determined by the precise GNSS RTK method. The measurement data were processed in the original software developed by the authors. The results demonstrate a high 2D positioning accuracy with low height determination accuracy. The course determination errors exceed the limit values declared by the manufacturer. However, specific measurement conditions must be taken into account, which differ considerably from the typical applications of a satellite compass.